KTI 1000Base-X Installation Manual

Text of KTI 1000Base-X User Guide:

• KTI 1000Base-X, 2 The information contained in this document is subject to change without prior notice. Copyright (C) All Rights Reserved. TRADEMARKS All brand names are trademarks or registered trademarks of their respective holders. Warning This equipment has been tested and found to comply with the limits for Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and if not installed and used in accordance wi

• KTI 1000Base-X, 3 CISPR 22 Class B This device complies with EMC directive of the European Commu- nity and meets or exceeds the following technical standard: EN 55022 - Limits and Methods of Measurement of Radio Interference Char- acteristics of Information Technology Equipment. This device com- plies with CISPR 22 Class B. CE NOTICE Marking by the symbol indicates compliance of this equip- ment to the EMC directive of the European Community. Such marking is indicative that this equipment meets or exceeds the following technical standards: EN55022/CISPR 22 ClassB EN55024 - EN61000-3-2, EN61000-3-3, EN61000-4 series

• KTI 1000Base-X, 4 Introduction The 1000BASE-X Gigabit Ethernet PCI Adapter is a 32-bit LAN adapter for use in personal computers with PCI computer bus slots. This adapter features a mini-GBIC fiber connector (SFP) for a 1000 Mbps IEEE 802.3z Ethernet network connection over optical fiber cable. The series provides different fiber transceiver types support- ing short, middle, and long reach applications. Adapter Features  Supports 32-bit 33/66MHz PCI of Rev.2.1/2.2/2.3 specifica- tion  IEEE 802.3z 1000Base-SX/LX compliant  Provides Tx 8K / Rx 64KB RAM buffer  Supports full duplex operation up to 2000Mbps data rate over fi

• KTI 1000Base-X, 5 Specifications Standards IEEE 802.3z 1000Base-SX/LX Network Port SFP for 1000Mbps mini-GBIC fiber transceiver Host Interface 32-bit 33/66Mhz PCI Rev.2.1/2.2/2.3 LEDs SFP status, Link status, Optical status Network Cables 50/125 multimode fiber up to 500m 62.5/125 multimode fiber up to 220m 9/125 single mode fiber Transfer Rate Gigabit Ethernet: 2000Mbps (Full-duplex) Driver Support Windows XP, Windows Vista, Windows 7, Windows 8, Windows Server 2008, Linux Power Consumption PCI 3.3V/400mA max. Dimension 130 x 65 mm Environment Operation Temperature

• 7 Adapter with PCI low-profile bracket No. Components Description 1 LINK LED This LED lights when the fiber connection is established. 2 SFP LED This LED lights when a mini-GBIC transceiver module is installed in the SFP slot. 3 OL LED This LED lights when optical signal is presented in the transceiver. 4 SFP Slot This slot supports mounting a mini-GBIC fiber transceiver.

• KTI 1000Base-X, 8 Installing the Adapter Before installing the adapter, you need the following: • A computer system that is compliant with the PCI specifica- tions version 2.1 or later. • An available PCI bus master slot in the computer • The adapter driver diskettes (or CD supplied with the adapter) • Fiber cables Inserting the Adapter into the PCI Slot To install the adapter in your computer, follow these steps: 1. Turn off the power to the computer. 2. Remove the computer's cover. 3. Unscrew and remove the slot cover from the PCI bus slot. 4. Insert the adapter into the slot and secure the screw. 5. Replace the computer cover and reconnect all previously connected cables.

• 9 Installing Mini-GBIC Transceiver A typical mini-GBIC SFP transceiver is shown as follows: To install a fiber transceiver into the SFP slot, the steps are: 1. Insert the fiber transceiver into the mini-GBIC SFP port. Normally, a bail is provided for every SFP transceiver. Hold the bail and make insertion. 2. Until the fiber transceiver is seated securely in the slot, place the bail in lock pos

• KTI 1000Base-X, 10 Connecting to the Network The rear bracket of the PCI adapter contains two fiber connectors. The TX connector is used for transmission and the RX is used for reception. When connecting to a device using fiber cable, make sure the TX connector of the adapter is connected to the RX connector of the device and RX connector is connected to the TX connector of the device. In order to have a reliable communication between two ends, the speed and duplex configuration of the adapter's fiber port and the device at the remote end must be same. Configure the driver of the adapter as follows: Auto, 1000Mbps, Full-d

• KTI 1000Base-X, 11 Network Driver Installation After making the connection to the network, you must install the adapter network driver in order to connect the network adapter to your network operating system. The adapter driver media contains the latest versions of the network drivers available when the adapter is shipped from the factory. A file, \README.TXT, located in the associated product directory contains a list of the supported driver software and the directory structures for the supported operating environments. Please refer to thi

• KTI 1000Base-X, 12 LED Indicators The adapter has three LEDs. The interpretations of the LEDs are: LINK LED indicates an active 1000Mbps connection is established. On : Good link between the adapter and a remote device Off : No connection between adapter and a remote device Blink: Link on and traffic activities SFP LED indicates installation status of mini-GBIC transceiver On : A mini-GBIC SFP transceiver is installed in the SFP slot. Off : No transceiver is installed. OL LED indicates optical signal status On : Optical signal is detected. Off :

Related Products and Documents (PCI Card):

Comparable Devices:

Similar Resources:

• Aaeon PER-V02B (13 pages) Mini PCI TTL to DVI Module PER-V02B PER-V02B Quick Installation Guide 1 Notice This guide is designed for experienced users to setup the system in the shortest time. Safety Precautions Always completely disconnect the power cord from your board whenever you are working on it. Do not make connections while the power is on, because a sudde …

• Danpex ADP1100 (3 pages) 1PCI 10/100TXFast Ethernet BoardUser’s Manual(GMF1439K-003)1. ChecklistBefore you start installing the PCI 10/100TX, verify that thePackage contains the following items:— PCI 10/100TX Board— LAN Driver Diskette— This User’s ManualPlease notify your sales representative immediately if any ofthe aforementioned items is missing or damaged.2. Over …

• IEI Technology MPCIE-CAN-R10 (4 pages) MPCIE-CAN PCIe Mini CAN Bus Card Quick Installation Guide Version 1.00 April 26, 2019 Features  Supports dual CAN 2.0B port  USB 2.0 based; no additional driver required  Galvanic isolation 2500 V  Operation temperature: -20°C to 60°C Packing List  1 x MPCIE-CAN card  2 x CAN-bus cable (3-pin wafer to DB-9)  1 x QIG …

• TRENDnet TEW-441PC - 108Mbps Wireless PC Card TEW-441PC (9 pages) i Regulatory notes and statements Wireless LAN, Health and Authorization for use Radio frequency electromagnetic energy is emitted from Wireless LAN devices. The energy levels of these emissions however are far much less than the electromagnetic energy emissions from wireless devices like for example mobile phones. Wireless LAN devices are safe for use frequ …

• Nat NAT-MCH (57 pages) NAT-MCH Clock-Module – Technical Reference Manual NAT-MCH Clock-Module Technical Reference Manual V 1.4 CLK Module HW Revision 2.1 and Revision 2.3 …

• Objective Imaging OASIS-blue (6 pages) OASIS-blue Installation Guide Rev. A Warning! This board contains static sensitive components. Please take the necessary precautions when handling and installing the board, to prevent damage or malfunction. Please take care not to overstress the high-density front-panel connectors. Do not plug or unplug motors while the board is powered-up, as this m …

Comments, Questions and Opinions: