Manualios.com

mbot 3d CUBE Operation & User’s Manual

mbot 3d CUBE Manual Online:

3.5, 2435 votes
mbot 3d CUBE User Manual
mbot 3d CUBE User Guide
mbot 3d CUBE Online Manual

Text of mbot 3d CUBE User Guide:

  • mbot 3d CUBE, MagicFirm Technical Support : [email protected] 21 5 5 5 5 Printing Printing Printing Printing 5.1 5.1 5.1 5.1 Printing Printing Printing Printing from from from from computer computer computer computer 1) Clear the blue build bed. Then click the “ Print ” button (as shown above) at the upper left corner of the window. If a prompt pops up warning “ You ’ re moving too fast! ” , never mind. Click the “ Proceed anyway ” button to keep printing. The machine can handle that. 2) The windo

  • mbot 3d CUBE, MagicFirm Technical Support : [email protected] 10 which means the machine is OK. 2.2 2.2 2.2 2.2 Connect Connect Connect Connect to to to to computer computer computer computer Make sure your computer is connected to your MBot with the supplied USB cable . 2.3 2.3 2.3 2.3 Setting Setting Setting Setting up up up up software software software software 1. Double-click the desktop icon to run ReplicatorG.

  • mbot 3d CUBE, MagicFirm Technical Support : [email protected] 33 7 7 7 7 Contact Contact Contact Contact Us Us Us Us Thank Thank Thank Thank you you you you for for for for choosing choosing choosing choosing MBot MBot MBot MBot desktop desktop desktop desktop 3D 3D 3D 3D printer! printer! printer! printer! http://www.mbot3d.c om

  • mbot 3d CUBE, MagicFirm Technical Support : [email protected] 17 3) When finishing setting up, click the “ Generate Gcode ” button and you ’ ll see the following window showing progress bars. 4) After GCode is generated, you ’ ll see the “ gcode ” tab next to the “ model ” tab. 5) Click the ” gcode ” tab and you ’ ll see the window as shown below.

  • mbot 3d CUBE, MagicFirm Technical Support : [email protected] 7 printer driver. When another “ Windows Security ” pop - up appears, click on “ Always install th e driver (I) ” . 5) Click the “ Finish ” button to complete driver installation. While on the “ ReplicatorG Installer ” window, click the “ Next ” button to finish the installation of ReplicatorG .

  • mbot 3d CUBE, MagicFirm Technical Support : [email protected] 23 4) If you want to pause or stop printing, click the buttons as shown below. NOTE: I n the initial phase of printing (when the message area below toolbar is yellow), the Pause and Stop buttons are disable. You can close ReplicatorG to pause printing. While printing, it may take 30 seconds to pause after clicking the Pause button, which depends on c omputer c onfiguration s. DON ’ T hit the Pause button again. 5) When finishing printing, you ’ ll see the icon below. Take the model out by hand or shoveler . Don ’ t break the blue tape while using shoveler . If the blue tape is broken, do remember to stick a piece

  • MagicFirm Technical Support : [email protected] 27 4) Select “ Yes ” and press the center key , to stop printing. The LCD screen resets itself. 5.3 5.3 5.3 5.3 3D 3D 3D 3D outputs outputs outputs outputs Support structure can be moved by hand or other tools.

  • mbot 3d CUBE, MagicFirm Technical Support : [email protected] 2 Contents 1 Installing s oftware ................................................................................................................... 3 1.1 Installing Python ....................................................................................................... 3 1.2 Installing ReplicatorG ............................................................................................... 5 2 Pre-print checks ...................................................................................................................... 9 2.1 Power up .........................................................................

  • mbot 3d CUBE, MagicFirm Technical Support : [email protected] 1 CUBE CUBE CUBE CUBE THE THE THE THE DESKTOP DESKTOP DESKTOP DESKTOP 3D 3D 3D 3D PRINTER PRINTER PRINTER PRINTER USER USER USER USER MANUAL MANUAL MANUAL MANUAL 2012-12-05

  • mbot 3d CUBE, MagicFirm Technical Support : [email protected] 14 3 3 3 3 Setting Setting Setting Setting up up up up model model model model data data data data 3.1 3.1 3.1 3.1 I I I I mporting mporting mporting mporting model model model model file file file file into into into into ReplicatorG ReplicatorG ReplicatorG ReplicatorG 1)The machine supports STL, OBJ, Gcode and collada model files. You can use 3D design software (such as Rhinoceros , Solidworks, Sketchup, UG, etc.) to convert file format. Click “ File->Open ” to open the model file. 3.2 3.2 3.2 3.2 Move, Move, Move, Move, s s s

  • mbot 3d CUBE, MagicFirm Technical Support : [email protected] 11 2.Choose extruder nozzle and connection serial port. 1) Click GCode->GCoder Generator, and select “ Skeinforge(47)-Legacy ” . 2) Click Machine->Machine Type (Driver) . If your printer is dual-extruder, select “ The MBot Cube Dual ” . If it ’ s a single-extruder machine, select “ The MBot Cube Single ” .

  • MagicFirm Technical Support : [email protected] 9 2 2 2 2 Pre-print Pre-print Pre-print Pre-print checks checks checks checks 2.1 2.1 2.1 2.1 Power Power Power Power up up up up 1) Ensure the power cable is attached (see the picture below), and then switch on. 2) The LCD screen reads “ Heater Error! ” , which can be fixed by heating up through software. Press any botton at the rig

  • mbot 3d CUBE, MagicFirm Technical Support : [email protected] 12 3) Click Machine->Connection (Serial Port) ->COM(Number). If you have only one printer, select the latest port. If you have more than one printer, please select the port according to your printer. If there ’ s no s erial p ort on the menu, please click Machine->Connection (Serial Port) ->Res can S erial Port. If it doesn ’ t work, please close ReplicatorG , disconnect the USB cable from your computer, and wait for 5 seconds. Then connect the USB cable to the computer, run ReplicatorG , and click Machine->Connection (Se

  • mbot 3d CUBE, MagicFirm Technical Support : [email protected] 31 raft/support ” option and select “ None ” in the “ Support Material ” list. Because two models can support each other. Strongly recommend using default settings in other options. 3) Click “ Generate Gcode ” on the two windows. Then the windows show as below. 4) It takes about 30 minutes to generate GCode. When finishing generating, the window shows as below.

  • MagicFirm Technical Support : [email protected] 15 Put on Platform: T he model is resting on the surface of the platform, not suspended in air or below the platform . Check Check Check Check it it it it before before before before printing. printing. printing. printing. X — 、 X+ : Move left or right. Lock Hight: When it ’ s checked, the height won ’ t chan

  • mbot 3d CUBE, MagicFirm Technical Support : [email protected] 22 3) If a prompt appears “ Monitor print temperature: Closed ” at the top right corner of the window, click File->Preferences. On the “ Preferences ” window, check the “ Monitor print temperature ” option and then close the pop-up window.

  • mbot 3d CUBE, MagicFirm Technical Support : [email protected] 16 3.3 3.3 3.3 3.3 Generating Generating Generating Generating GCode GCode GCode GCode ( ( ( ( Slicing Slicing Slicing Slicing ) ) ) ) 1) Click the “ Generate GCode ” button at the lower right corner of the window. Then the following prompt pops up, if the model is adjusted but not saved. Click “ Yes ” to save changes. Otherwise, click “ No ” . But But But But please please please please click click click click “ “ “ “ Cancel Cancel Cancel Cancel ” ” ” ”

  • mbot 3d CUBE, MagicFirm Technical Support : [email protected] 3 To get a better printing experience, we suggest you to take time reading this manual. It is designed to illustrate the procedures from the installment of software to operation , and get you up and running as quickly as possible. 1 1 1 1 Installing Installing Installing Installing s s s s oftware oftware oftware oftware 1.1 1.1 1.1 1.1 Installing Installing Installing Installing Python Python Python Python 1 ) Go to http://www.mbot3d.com/pages/software , and download replicatorg and python2.6

  • MagicFirm Technical Support : [email protected] 24 1) Make sure your SD card is in the SD card slot of your computer. After GCode is generated, click the button as shown below. On the pop-up window , find and open SD card. Input file name and save in s3g format. The printer can read s3g file only. Make sure the file name isn ’ t in Chinese or too long. Otherwise, the pinter may make e

  • mbot 3d CUBE, MagicFirm Technical Support : [email protected] 30 6 6 6 6 Two-color Two-color Two-color Two-color printing printing printing printing To print a model with two colors, you ’ ll have to slice the model file. Build models for each color. Then generate GCode by ReplicatorG. Take two-color Earth for example. The picutre below shows the model after slicing. 1) Click the “ File ” menu and choose the file. (Here, we open “ 双头打印合 并 .stl ” .) The pop-up window shows as below. 2) Click the “ Merge ” button and you ’ ll see three pop-up windows as shown below. On the two setting windows for GCode generator, uncheck the “ use

  • mbot 3d CUBE, MagicFirm Technical Support : [email protected] 25 2) After the Gcode file is saved, the window shows as below. 3) Take out the SD card from your computer and insert it into the printer. Then Select “ Print from SD ” and choose the model file, by up and down arrow keys beside the LCD screen. Press the center key to enter after selecting.

  • mbot 3d CUBE, MagicFirm Technical Support : [email protected] 13 5) When the machine is connected succesfully, the message area below toolbar turns green. Otherwise, red. When the machine is running safely, it turns yellow. Helpful Hint: When the machine can ’ t be connected, please check : � P ower is being supplied to the printer . � Y our computer is connected to your MBot with the supplied USB cable . � Driver is installed successfully.

  • mbot 3d CUBE, MagicFirm Technical Support : [email protected] 19 4 4 4 4 Test Test Test Test print print print print ing ing ing ing ( ( ( ( If If If If plastic plastic plastic plastic stop stop stop stop com com com com ing ing ing ing out out out out the the the the nozzle nozzle nozzle nozzle during during during during printing, printing, printing, printing, please please please please read read read read this this this this chapter chapter chapter chapter ) ) ) ) Please test nozzles before your first printing, which is required for

  • mbot 3d CUBE, MagicFirm Technical Support : [email protected] 28 When assembling the bracket (i.e. our printing example since chapter 3) to hold material, please push in the direction as the red arrow points, in order to get the maximum space.

  • mbot 3d CUBE, MagicFirm Technical Support : [email protected] 5 Click the “ Finish ” button to exit the installer. 1.2 1.2 1.2 1.2 Installing Installing Installing Installing ReplicatorG ReplicatorG ReplicatorG ReplicatorG 1) Double-click ReplicatorG, and you ’ ll see the following window. 2) Click the “ Next ” button. Then on the following window, click the “ Install ” button. Suggest using the default destination folder.

  • MagicFirm Technical Support : [email protected] 26 2) After selecting file and pressing the center key, the printer starts to heat up. The LCD screen shows as below. 3)If you want to cancel printing, please press the left arrow key (i.e. the back button). A message appears as below.

More Instructions:

DOWNLOAD

Related Products and Documents (3D Printers):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 Altec Lansing CHP524 Specification sheet altec-lansing/chp524-5K2.pdf 03 Jan 2024 3 0.36 Mb
2 King Pigeon W22 Operation & user’s manual king-pigeon/w22-5KW.pdf 28 Nov 2022 8
3 IBM Travelstar 6GN Quick installation manual ibm/travelstar-6gn-TSO.pdf 14 Aug 2022 2
4 Magellan RoadMate 3000T - Automotive GPS Receiver Installation instructions magellan/roadmate-3000t-automotive-gps-receiver-Z91.pdf 19 Nov 2022 1
5 nuVita 1015 Instructions for use nuvita/1015-4V4.pdf 12 Dec 2022 2
6 mundoclima MUENR-30-H7T Installation & owner's manual mundoclima/muenr-30-h7t-L67.pdf 31 Aug 2023 46

Similar Resources:

  • AIO ROBOTICS

    ZEUS

    (2 pages)
    AIO ROBOTICSQUICK STARTUSER GUIDE Congratulations on purchasing ZEUS: The world’s first all-in-one 3D printer. This guide is designed to help you unpack and load the included accessories and filament correctly. Follow the simple instructions and you’ll experience your first successful printout in around 10 minutes. www.zeus.aiorobotics.com TMZEUS: Chan …
  • BDSL

    Ultimaker2

    (30 pages)
    !"#$%&'(&')#*&(+#,-(&./01%23#,41%#5/'6/-#7#8#9":;#2<7=#>1?%6/%@#2=3#2<7=## # # # # # # ##!3D!Printing!with!Ultimaker2,!User!Guide!###,'&A1%4&(@#BC#D&E(B%&/3##F9":;G#9&B.1H&E/-#:@4(1.4#"14&)'#;/?B%/(B%@### …
  • SeeMeCNC

    Rostock MAX v2

    (281 pages)
    Rostock MAX v2 Assembly GuideWelcome to the Assembly Guide for the Rostock MAX v2.0 3D printer.Version 1.68, September 28th, 2016Repetier-Host EditionCopyright 2014 by Gene BuckleLicensed as Creative Commons Attribution-ShareAlike 3.0Questions or corrections should be emailed to [email protected]
  • Anet

    ET5 X

    (2 pages)
    Use InstructionV1.0Machine Net WeightStandard Nozzle DiameterHotbed TempAuto LevelingResume PrintingOffline PrintFilament DetectionAuto Filament DispenserLanguageExtruder Working TempSpecificationsFilamentModelPrinting SizePrinting TechnologyMachine SizePower SupplyMachine PowerPrinting SpeedPrinting ResolutionSlice ThicknessPLA 1.75mm360WET5 X300*300*400mm …
  • FLASHFORGE 3D PRINTER

    Creator Pro

    (15 pages)
    This guide is only applicable to FLASHFORGE Creator Pro 3D printerThe User Guide is in the SD card.USERGUIDECREATOR PRO2. Hot! Avoid touching the heating nozzle in operation. 3. Moving parts in printer may cause injury. Do not wear gloves or other sources of entanglement in operation.WARNING1. Do not remove the wrapping around the nozzle. Quick Star …
  • SainSmart

    Prusa i3

    (13 pages)
    1 Troubleshooting Manual Please be aware of these options as follows : 1. Mainboard is sensitive to static electricity. Please Touch a grounded object to release static electricity before operation. 2. Please ensure the power wire connection is correct. 3. Please Cut off the power when changing interface connection. …

Comments, Questions and Opinions: