Manualios.com

Aim MyChron5 Operation & User’s Manual

Aim MyChron5 Manual Online:

4.75, 2965 votes
Aim MyChron5 User Manual
Aim MyChron5 User Guide
Aim MyChron5 Online Manual

Text of Aim MyChron5 User Guide:

  • CHAPTER 5 ONLINE 20 21 MYCHRON5 5.Online Some pages are available for the online data visualization. You can scroll them by pushing the VIEW button. Depending on the configuration of your MyChron5 (gear presence, expansions, SmartyCam connection), the pages may change. At least three pages are always available: n Track Selected Page: This is the page that app

  • Aim MyChron5, 1. MyChron5 in a few words MyChron5 is a gauge designed for being installed on a kart. 02 03 It reads and records: n RPM at high frequencies (up to 50 times per second) from the spark cable n One or two temperature values (depending upon the model). They can be exhaust gas, underspark, or water temperatures. n All parameters coming from the GPS/Glonass costellations: speed, position, lateral acceleration and time of day with precision of one millisecond. The receiver has been tuned for our sport, so it accepts all the strong lateral and

  • Aim MyChron5, CHAPTER 7 34 35 MYCHRON5 Once the WiFi authentication with the device has been established, users can interact with the device by clicking on it. In this scenario, both your MyChron5 and PC join an existing WiFi network (WLAN). This scenario is ideal for a race team with multiple drivers and crewmembers and it is desired to communicate with one or more AiM devices using the same PC network. Note again that each MyChron5 can have a unique password, which is in addition to the network password, thus adding an additional layer of privacy and security. Race Studio 3 will display any and all MyChron5 devices connected to the same network as the PC. Conn

  • Aim MyChron5, CHAPTER 7 36 37 MYCHRON5 In order to accomplish these tasks, Race Studio 3 has to be used as clarified in the following figure. As you can see by the picture above, one device called “MyChron5 ID 43008208” is switched from AP mode to WLAN mode. The network name is “network_2,” and it is not working in open authentication mode since it is protected by a network password. In order to get the connectivity to the device, the user’s PC also has to be authenticated to the same network, as clarified in the following figure. Once the user’s PC is authenticated to the same network called “network_2,”

  • Aim MyChron5, 12. New Firmware and Software Releases After downloading the MyChron5 firmware, you have to connect your MyChron5 to your PC via WiFi for executing the Firmup function. After a few seconds, your MyChron5 will be ready. Our technicians and engineers are constantly working to improve both firmware (the program that resides inside your system) and software (the program that you run in your PC). Every time a new firmware or software are available, an icon appears in your Race Studio 3 software: Please click on it and freely download and install the new programs. CHAPTER 12 NEW FIRMWARE MYCHRON5 MANUALE IMPAGINATO.qxp_La

  • Aim MyChron5, 04 05 CHAPTER 1 GETTING STARTED MYCHRON5 Power comes from the internal battery or, as an option, from the external power supply. The battery is included. It is a huge, removable three-amp lithium ion rechargeable battery, which comes with a battery charger. It may give power to your system for ten hours. MyChron5 is expandable: you can connect to the CAN bus: - SmartyCam HD - Lambda Sensor - MyChron Expansion The display is a wide LCD display with an RGB backlight that you can easily configure. By the way, the backlight automatically tur

  • Aim MyChron5, CHAPTER 4 CONFIGURATION 14 15 MYCHRON5 The lap setup brings you to the following page: Lap show time can change between: n static n rolling n - +/- best n predictive RPM frequency: RPM can be read 20 or 50 times per second ( 20 or 50 Hz), in dependence upon your necessities: 20 samples per second let you have a cleaner signal, and make easier to see the RPM trend, while 50 samples per second let you better recognize the vibration of the chassis and all the strengths that can create problems to the ideal movement of your kart. In the above picture you can see both dat a, at 20 and 50 Hz, in order to note

  • Aim MyChron5, CHAPTER 12 TECHNICAL DRAWINGS 46 47 MYCHRON5 MyChron5 n n n n n n n n n n n n n Our web site, www.aim-sportline.com is constantly upgraded. Please, refer to it for downloading the last release of our documentation MANUALE IMPAGINATO.qxp_Layout 1 25/11/15 16:04 Pagina 59

  • CHAPTER 1 06 07 GETTING STARTED MYCHRON5 - MyChron5 gauge - RPM cable - Temperature sensor - Battery Charger whith cable 2. What is in the kit? 1 2 1 2 3 4 4 3 MANUALE IMPAGINATO.qxp_Layout 1 25/11/15 16:03 Pagina 9

  • Aim MyChron5, CHAPTER 5 ONLINE 22 23 MYCHRON5 n Bar Graph Page with Speed: This is similar to the previous one but with speed (km/h or mph) shown on the right. MANUALE IMPAGINATO.qxp_Layout 1 25/11/15 16:04 Pagina 27

  • 3. Installation RPM Clip Installation Your MyChron5 has been designed for being installed on the steering wheel of your kart. In order to reduce vibrations to your MyChron5, please mount the rubber washer above and under the spoke of the steering wheel, as shown the picture below: Temperature sensor Installation CHAPTER 3 INSTALLATION 10 11 MYCHRON5 "Do not run the RPM lea

  • Aim MyChron5, CHAPTER 8 42 43 MYCHRON5 For establishing the WiFi connection with your PC: n be sure your MyChron 5 has the WiFi enabled (MyChron 5 MENU / WiFi Menu / WiFi mode has to be ON) n read the name of your MyChron 5, available in the center of the lower row of the OnLine Page: n click on the WiFi Icon of RaceStudio3 and select your MyChron 5: n OnLine n Data Download n Wifi and Proprierties n Odometers Management n Logo Management n Firmware Information The OnLine page lets you check all the MyChron 5 channels. Data Download is explained in chapter 10 Odometers Management lets you set the name and reset the value of 5 different od

  • Aim MyChron5, CHAPTER 7 42 43 MYCHRON5 If you want to be sure the communication is working, choose the “Open Network Preferences…” menu. In Race Studio 3, flag the checkbox you find in Preferences. In the window, you’re prompted to verify that the status is shown as connected and that the given IP is, for example, 10.0.0.10 (it could be 10.0.0.11, 10.0.0.12, or generically 10.0.0.x). MANUALE IMPAGINATO.qxp_Layout 1 25/11/15 16:04 Pagina 47

  • Aim MyChron5, CONFIGURATION MYCHRON5 4.1 Backlight You can set the backlight to on, off, or automatic. In this last case, the light sensor positioned on the front left of your MyChron5 turns the light on or off depending on the external light level. Here, you can also change the backlight color, choosing among six different possibilities. 4.2 Parameter Configuration Please select the Param Config icon for setting the general purpose parameters. Through this page you can set: n Unit of measure for speed (Km/h or mph) and temperature ( Celsius or Fahrenh

  • Aim MyChron5, CHAPTER 4 CONFIGURATION 12 13 MYCHRON5 4. Configuration Menu Before using your MyChron5, don't forget to set some parameters, as explained below. You can enter the Configuration Menu by pressing the MENU button. The icons have the following meanings: The Wizard icon helps you to set the most important parameters of your new MyChron 5: n Language n Temperature unit (Fahrenheit or Celsius) n Speed unit (mph or Km/h) n Maximum RPM n Drive type (direct drive, low-stall clutch, gearbox) By scrolling through the ic

  • Your MyChron5 comes with the information about a good number of kart tracks already available in it. Our technicians are constantly working to upgrade the database, and new releases of it are freely downloadable using the Race Studio 3 software. If you need to upgrade the track information in the gauge, please refer to chapter 9. After selecting the Tracks icon, you enter into the Tr

  • Aim MyChron5, CHAPTER 7 WIFI CONFIGURATION 30 31 MYCHRON5 Follow these steps to create an AP, allowing you to connect your PC to your MyChron5 via WiFi. This is the most simple and direct WiFi connection method and is ideal when you wish to communicate with only one MyChron5 using one PC. Your MyChron5 as a default, is configu- red as an Access Point and creates a network, without a password, completely accessible to everyone. So, for establishing the Wi Fi connection: n be sure your MyChron5 has the WiFi enabled n read the name of your MyChron5, available in the lower row of th

  • Aim MyChron5, CHAPTER 7 WIFI CONFIGURATION 32 33 MYCHRON5 The name of this AP, or SSID, is unique to your device. An example name is: “AiM-M5-054321" Whereas: n “AiM” is the prefix for all AiM devices; n “M5” is type of system identifier; and n “054321” is a unique serial number for your device assigned at the factory. To make your device more recognizable, you can append a friendly name to the SSID. There is a limit of eight characters. For example, if you add the driver's name, Tom Wolf, the resulting network name (SSID) will be: AiM-M5-054321-Tom Wolf After having set all the parameters, click the Transmit and Restart button. Your MyChron5 will re start and be confi

  • Aim MyChron5, CHAPTER 4 CONFIGURATION 18 19 MYCHRON5 The tracks in the dbase are shown in the upper part of the display. The nearest are shown first. You will see the name of the track, the shape, and the distance from where you are. In the lower part of the track, the selected track is shown. Please, note that, in case you run on a kart track that is NOT described in our track database, MyChron5 enters into an "Apprentice mode", doing the following steps n It starts recording the different points of the track n As soon as it realize

  • Aim MyChron5, CHAPTER 6 DATA RECALL 24 25 MYCHRON5 6. Data Recall After having finished your test, you can review the data by pressing the MEM/OK pushbutton. In every square, you can read the time of the test, how many laps, and the best lap time. These two pages don't appear if you have just finished your test; in this case, you see the following on the first page: If your last test was at least one day ago, you can enter the summary page: It shows the best thr ee laps of your test, giving the information about maximum and minimum RPM, speed, and temperature(s) for them. By pushing NEXT, you get: It shows the three split times for the best lap. There

  • Aim MyChron5, CHAPTER 7 40 41 MYCHRON5 For optimal network speed for your AiM device(s), we have recommended not allowing an internet connection on the same network and have provided WLAN settings that prohibit an internet connection. Please know that it is certainly possible to allow internet access on the same network as your AiM device(s), but doing so can degrade the performance of AiM device communication. These slightly slowe r network speeds may be suitable for your needs. Also note that it is possible to have a second WiFi connection by means of additional hardware (NIC

More Instructions:

DOWNLOAD

Related Products and Documents (GPS):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 General DM8200 Operation & user’s manual general/dm8200-5L6.pdf 16 Jan 2024 20
2 Craftsman 917.388652 Owner's manual craftsman/917-388652-I58.pdf 09 Apr 2023 40
3 Konica Minolta BIZHUB 500 Operation & user’s manual konica-minolta/bizhub-500-QSD.pdf 24 Jun 2022 774
4 Avantree BTHS-AS9S Operation & user’s manual avantree/bths-as9s-RZ3.pdf 03 Apr 2023 7
5 Reebok Elliptical Exerciser/rel2i Manual  reebok/elliptical-exerciser-rel2i-5OZ.pdf 18 Dec 2023 16 0.47 Mb
6 Telemotive 10K JLTX Operation & user’s manual telemotive/10k-jltx-8RZ.pdf 20 Aug 2023 11

Similar Resources:

  • MyFlyDream

    TeleFlyTiny

    (5 pages)
    TeleFlyTiny Module Quick Reference V1.1 www.MyFlyDream.com You can use a separate GPS or share a GPS with your AutoPilot. In case of sharing a GPS, you need to connect these wires in the above picture: PortA P#2 GND : Connect to the GND wire of your GPS. PortA P#3 U2 RX: Connect to the TXD wire of your GPS. PortA P#13 GND: Connect to the Power - PortA P#14 …
  • Novatel

    PwrPak7

    (4 pages)
    1Box ContentsPower Cable USB Cable COM1 Serial CableOther Equipment NeededGNSS Antenna 50Ω Coaxial Antenna Cable9-36 VDC Power Supply Capable of 15 WComputer, Tablet or Smart PhonePwrPak7® FamilyQuick Start Guide …
  • GoFind

    GoFindR

    (9 pages)
    !Welcome to the GoFindR Family! Quick Start Guide GoFindR Pet Tracker GoFindR is a registered trademark of GoFind, Inc. 3103 Stonehenge Dr Richardson, TX 75082 Email: [email protected] www.gofindinc.com! …
  • Qstarz

    Travel Recorder NANO BT-Q1300

    (70 pages)
    Beyond NavigationEnglish……………………………………………………………………………………………………………………………………………………………………………………….……………………………………………………� …
  • Rexing

    V1

    (45 pages)
    1 © 2018 REXING All Rights Reserved V1 User Manual The information in this manual is subject to change without notice. www.rexingusa.com 01/2018Rev10 …
  • Garmin

    GPSMAP 4012 - Marine GPS Receiver

    (2 pages)
    Printing a gPSMaP® 4000/5000 SerieS FluSh Mount teMPlate in adobe acrobatNotes:(A) Youmustprintthetemplateon11˝x17˝paper.Thisisnormallyselectedinthe‘PrinterProperties’,andwilldifferbymanufacturer.• Ifyourprinterisnotcapableofprintingon11˝x17˝paper,or …

Comments, Questions and Opinions: