Panasonic EY4541 Operating Instructions Manual

Text of Panasonic EY4541 User Guide:

• Panasonic EY4541, Operating Instructions Bedienungsanleitung Instructions d’utilisation Istruzioni per l’uso Gebruiksaanwijzing Manual de instrucciones Brugsvejledning Driftsföreskrifter Bruksanvisning Käyttöohjeet Before operating this unit, please read these instructions completely and save this manual for future use. Vor Inbetriebnahme des Gerätes die Betriebsanleitung bitte gründlich durchlesen und diese Broschüre zum späteren Nachschlagen sorgfältig aufbewahren. Lire entièrement les instructions suivantes avant de faire fonctionner l’appareil et conse

• - 9 - Original instructions: English Translation of the original instructions: Other languages I. INTENDED USE Thank you for purchasing the Pana- sonic Jigsaw. This jigsaw can be used with Panasonic rechargeable batteries to provide excellent cutting perfor- mance. The jigsaw is for cutting metal, wood, and drywall only. Read the “Safety Instructions” bo

• Panasonic EY4541, - 10 - Symbol Meaning V Volts Direct current n 0 No load speed …min -1 Revolutions or reciproca- tions per minutes Ah Electrical capacity of battery pack To reduce the risk of injury, user must read and understand instruc- tion manual. For indoor use only. WARNING: • Do not use other than the Pana- sonic battery packs that are de- signed for use with this rechargea- ble tool. • Panasonic is not responsible for any damage or accident caused by the use of the recycled battery pack and the counterfe

• Panasonic EY4541, - 11 - 3. Insert the blade into the blade clamp bracket and set the back of the blade along the roller guide so that the back of the jigsaw blade slides along the roller guide. 4. Release the blade Attach/Remove lever. • When the blade is secured in place then lever will return to its original po- sition. • Check that the back of blade is setting in the groove in the roller guide. WARNING: If you do not insert the saw blade deep enough, the saw blade may be ejected unexpectedly during opera- tion. This can be extremely danger- ous. Removal 1. Lift up the blade Attach/Remove lever. 2. Pull out the blade. Adjusting the base 1. Use t

• Panasonic EY4541, - 12 - Position of base and purpose of use Base adjustment hole position Purpose of use Normal right-angled cutting Cutting at an angle between 0° and 45° Cutting at an angle of 45° Cutting close to the end of a wall NOTE: This is only a rough guide. The ac- tual angle of the cut will be affected by factors such as the way the tool is held against the surface. Adjusting the orbital stroke mode • Adjust the orbital stroke mode to the object to be cut. 3 2 1 0 Lever position Blad

• Panasonic EY4541, - 13 - Anti-splintering plate Use the anti-splintering plate to reducing splinter while cutting wood. Installation 1. Set the base at 90 degree position. 2. Place the anti-splintering plate on the underside of the base, and gently push it to be installed. • Install so that the beveled edge of the slot in the middle of the anti-splintering plate is facing toward the jigsaw. Dust adapter for vacuum cleaner ( EY9X009 ) (Available as an ac- cessory, not included) You can use a vacuum cleaner to collect cutting dust while cutting. Installation 1. Attach the hook of the dust collection

• Panasonic EY4541, - 14 - IV. OPERATION 1. Push the switch lock lever down, pull the power switch. • The speed increases with the amount of depression of the power switch. 2. Once cutting is finished, release the power switch. 3. Check that the temperature of the blade has dropped sufficiently, and then remove the blade. CAUTION: When operating the tool by pulling the trigger, there may be a momentary lag before rotation starts. This does not signal a malfunction. • This lag occurs as the tool’s circuitry starts up when the trigger is pulled for the first time aft

• Panasonic EY4541, - 15 - • When cutting complex shapes such as shapes with many small curves, reduce the cutting speed and the turning speed. Plunge cutting 1. Make a drill hole in the section to be plunge cut in order to let the blade pass through. 2. Insert the blade into a hole without touching the workpiece, and then turn on the power switch. 3. Cut along the marked line. Using a rip fence (EY9X011E) (Available as an accessory, not included) A rip fence can be used for cutting parallel lines and for cutting circles and arcs. Installing the

• Panasonic EY4541, - 16 - Cutting circles 1. If cutting away a section, make a drill hole on workpiece to let the jigsaw blade pass through. 2. Align the pin hole of the rip fence with the center of the circle, and then use a nail or screw to hold the object in place. 3. Without touching the workpiece, turn on the power switch. 4. Cut along the marked line. Control Panel (1) (3) (2) (1) LED light Before the use of LED light, always pull the power switch once. Press the LED light button. The light illuminates with very low current, and it does not ad- versely affect the performance of the driver d

• Panasonic EY4541, - 17 - • If the tool is used in cold-temperature conditions (such as during winter) or if it is frequently stopped during use, the overheating protection feature may not activate. • The performance of the EY9L42 dete- riorates significantly at and below 10°C due to work conditions and other factors. • The ambient temperature range is be- tween 0°C (32°F) and 40°C (104°F). If the battery pack is used when the bat- tery temperature is below 0°C (32°F), the tool may fail to function properly. • When charging a cool battery pack (below 0°C (32°F)) in a warm place, leave the battery pack at the place and wait for more than one hour to warm up th

• - 18 - [Battery Pack] For Appropriate Use of Battery pack Li-ion Battery pack • For optimum battery life, store the Li-ion battery pack following use without charging it. • When charging the battery pack, con- firm that the terminals on the battery charger are free of foreign substances such as dust and water etc. Clean the terminals before charging the batt

• - 19 - Li-ion Battery Pack NOTE: Your battery pack is not fully charged at the time of purchase. Be sure to charge the battery before use. Battery charger 1. Plug the charger into the AC outlet. 2. Insert the battery pack firmly into the charger. 1. Line up the alignment marks and place the battery onto the dock on the charger. 2. Slide forward in the direction of the arrow

• Panasonic EY4541, - 20 - LAMP INDICATIONS Charging is completed. (Full charge.) Battery is approximately 80% charged. Now charging. Charger is plugged into the AC outlet. Ready to charge. Charging Status Lamp. Left: green Right: orange will be displayed. Battery pack is cool. The battery pack is being charged slowly to reduce the load on the battery. Battery pack is warm. Charging will begin when temperature of battery pack drops. If the temperature of the battery pack is -10° or less, the charging status la

• Panasonic EY4541, - 21 - [Information on Disposal in other Countries outside the Euro- pean Union] These symbols are only valid in the European Union. If you wish to discard these items, please contact your local authorities or dealer and ask for the correct method of disposal. Note for the battery symbol (bottom two symbol examples): This symbol might be used in combination with a chemical symbol. In this case it complies with the requirement set by the Directive for the chemical involved. V. MAINTENANCE • Use only a dry, soft cloth for wiping the unit. Do not use a damp cloth, thinner, benzine, or

• Panasonic EY4541, - 22 - VII. SPECIFICATIONS MAIN UNIT Model EY4541 Motor 14.4 V DC Max thickness of mounting blade 1.3 mm Length of strokes 20 mm Strokes per minute 0 - 2400 /min Maximum cutting capacities Wood 65 mm Mild steel 6 mm Aluminum 10 mm Overall length 270 mm Weight (with battery pack) 2.25 k g Noise, Vibration See the included sheet BATTERY PACK Model EY9L41 EY9L42 EY9L44 EY9L45 Storage battery Li-ion Battery Battery voltage 14.4 V DC (3.6 V x 4 cells) 14.4 V DC (3.6 V x 8 cells) BATTERY CHARGER Model EY0L81 Electrical rating

• Panasonic EY4541, - 23 - VIII. ELECTRICAL PLUG INFOR- MATION FOR YOUR SAFETY PLEASE READ THE FOLLOWING TEXT CAREFULLY This appliance is supplied with a moulded three pin mains plug for your safety and convenience. A 5 amp fuse is fitted in this plug. Should the fuse need to be replaced please ensure that the replacement fuse has a rat- ing of 5 amp and that it is approved by ASTA or BSI to BS1362. Check for the ASTA mark or the BSI mark on the body of the fuse. If the plug contains a removable fuse cover you must e

More Instructions:

	Panasonic EY4541 Operating instructions manual 27-09-2023 148	DOWNLOAD
	Panasonic EY4541 Service manual 08-11-2023 12	DOWNLOAD
	Panasonic EY4541 Operating instructions manual 28-01-2023 148	DOWNLOAD
	Panasonic EY4541 Service manual 25-03-2023 12	DOWNLOAD

Related Products and Documents (Saw):

Comparable Devices:

Similar Resources:

• Bosch CRS180 (20 pages) 1-877-BOSCH99 (1-877-267-2499) www.boschtools.comOperating/Safety InstructionsConsignes d’utilisation/de sécuritéInstrucciones de funcionamiento y seguridadIMPORTANTRead Before Using●IMPORTANTLire avant usage●IMPORTANTELeer antes de usarFor English VersionSee page 2●Version françaiseVoir page 13●Versión en españolVer la página 26Call Toll F …

• Wolfcraft FKS 115 (72 pages) wolfcraft®GmbH Wolff-Str. 1D-56746 KempenichGermanywww.wolfcraft.comFKS 115l Original-Bedienungsanleitung (9)t Translation of the original operating instructions (12)p Traduction de la notice d'utilisation originale (15)n Traducción del manual de instrucciones original (18)L Vertaling van de oorspronkelijke handleiding (21)y Traduzione del manuale d� …

• HIKOKI C10FSH (100 pages) Slide Compound Miter SawPaneelsägeScie a coupe d'onglet radialeTr oncatrice portatileAfkortzaagmachine mettelescopisch zaagarmIngletadora telescopicaSerra telescópicaΦαλτσοκπτησ RadialC10FSH • C10FSBHandling instructionsBedienungsanleitungMode d’emploiInstruzioni per l’usoGebruiksaanwijzingInstrucciones de manejoInstruções de uso …

• Makita 7104L (48 pages) GB Chain Mortiser Instruction manualF Mortaiseuse à chaîne Manuel d’instructionsD Kettenstemmer BetriebsanleitungI Mortasatrice a catena Istruzioni per l’usoNL Kettingfrees GebruiksaanwijzingE Escopleadora de cadena Manual de instruccionesP Perfuradora de Corrente Manual de instruçõesDK Kædestemmemaskine BrugsanvisningS Kedjestämmaskin Bruksanvisni …

• GreenWorks GD24CS (120 pages) CRD401OPERATOR MANUAL / BEDIENUNGSHANDBUCH / MANUAL DEL OPERARIO / MANUALE DELL’OPERATORE / MANUEL OPÉRATEUR / MANUAL DE UTILIZAÇÃO / GEBRUIKSAANWIJZING / РУКОВОДСТВО ОПЕРАТОРА / KÄYTTÖOPAS / ANVÄNDARHANDBOK / BRUKERVEILEDNING / BRUGSVEJLEDNING / INSTRUKCJA UŻYTKOWNIKA / NÁVOD K OBSLUZE / NÁVOD NA OBSLUHU / Uporabniški priroč …

• PEUGEOT EnergyBand-150 (39 pages) MANUEL D’UTILISATION OPERATING INSTRUCTIONSBEDIENUNGSANLEITUNGSCIE À RUBAN 2 VOLANTS • HEAVY DUTY BAND SAW• BANDSÄGE MIT 2 BANDSÄGENROLLENEnergyBand-150 …

Comments, Questions and Opinions: