Manualios.com

Rolls-Royce Silver Shadow Workshop Manual

Rolls-Royce Silver Shadow Manual Online:

3.85, 1151 votes
Rolls-Royce Silver Shadow User Manual
Rolls-Royce Silver Shadow User Guide
Rolls-Royce Silver Shadow Online Manual

Text of Rolls-Royce Silver Shadow User Guide:

  • Rolls-Royce Silver Shadow, Rolls-Ryce Silver Shadow B Bentley T Series Workshop Manual Chapter P KG.M. 1,4 1,l 1,4 2,5 2,5 2,s 23 2,5 2,5 23 1,7 32 2,s 2,5 32 4,1 2,5 62 4,4 23 1,4 5,3 23 - LB.FT. 10 8 8 10 18 18 18 18 18 18 18 12 23 18 18 23 30 18 45 32 18 10 38 18 - SIZE $ in. dia. U.N.C. in. A/F 4 in. dia. U.N.C. -& in. A/F -ir, in. dia. U.N.C. 4 in. A/F & in. dia. U.N.C. 3 in. A/F & in. dia. U.N.C. + in. A/F ig- in. dia. U.N.C. + in. A/F in. dia. U.N.C. 1 +in. A/F & in. dia. U.N.C. + in. A/F in. dia. U.N.C. + in. A/F & in. dia. U.N.C. 3 in. A/F ig- in. dia. U.N.C. in. A/F 4 in. dia. U.N

  • Rolls-Royce Silver Shadow, Chapter K FUEL SYSTEM AND CARBURETTERS SECTION PAGE K1 Fuel System K1 K2 Fuel Pumps K5 C K3 Air Cleaner K4 The Carburetters and Automatic Choke System K5 Throttle Control Linkage Settings K31 K6 Fuel Evaporation Emission Control System K43 K7 Fault Diagnosis K49 K8 Workshop Tools K55

  • Rolls-Royce Silver Shadow, Workshop Manual Rolls- Ro yce Silver Shadow B Bentle y T Series Chapter L 5. Replace exhaust emission control com- ponents, or heat exchanger water connection, if fitte.d. 6. Fill the system, using the correct anti- freeze/water mixture, verifying and adjusting the concentration level using the method described in Section L1 Coolant - To check.

  • Rolls-Royce Silver Shadow, Workshop Manual Rolls-Royce Silver Shadow I) Bentley T Series Chapter M Armature insulation-TO test 5. Fit the wiper arms and blades. then cheek the (see Fig. M75) 1. Subject the armature to an insulation test. setting of the parking switch as desc rlt)~d in Parking Switch - To adjust. 2. Check the armature windings for short and open circuits. S. If the commutator is worn, it can be lightly W heelboxes skimmed in a lathe using a diamond-tipped tool. The wheelboxes are lubricated on initial assembly 4. After skimming, undercut the armature and and do not require any maintenance. They are remove all burrs by

  • Rolls-Royce Silver Shadow, Workshop Manual Rolls Royce Silver Shadow 6 Bentley T Ser~es Chapter J 2. Fit the final drive unit as instructed under 'Final A 8 drive unit-To fit', carrying out Operations 1 to 8, with the exception of Operation 4, the half-shafts being left disconnected from the yokes but supported. 3. With the final drive unit fitted to the cross- member, a check must now be made to ensure that the final drive is centrally positioned. FIG. 518 FINAL DRIVE POSITION CHECK 4. Measure from the face of the hub yoke, on which 1 Left-hand half-shaft

  • Rolls-Royce Silver Shadow, Workshop Manual Rolls-Royce Silver Shadow (including Long Wheelbase Saloon) Rolls-Royce Corniche Bentley T Series and Bentley Corniche Up to and including car serial number 30000 Volume 2

  • Workshop Manual Rolls Royce Silver Shadow 8 Bentley 7 Serles Chapter N 7. The fluid level indicated on the filler cap dip- stick should be raised to the 'FULL' mark by the addition of more fluid. Do not overfill. Fit the filler cap. Note (1) If the fluid level in the reservoir rises more than 4 in. (6,35 mm.) when the engine is switched &

  • Rolls-Royce Silver Shadow, Llls-Royce Silver Shadow B Bentley T Series Workshop Manual Chapter L Pints Litres (Imp.) FIG. 13 ANTI - FREEZE CONCENTRATION CORRECTION CHART TO GIVE A 50% SOLUTION A Acceptable service range of concentration B Freezing point of coolant C Percentage concentration D Volume of 100% anti-freeze to be added to maintain a 50% solution after removal of the same volume of old coolant first

  • Rolls-Royce Silver Shadow, Workshop Manual Rolls-Royce Silver Shadow 8 Bentley T Series Chapter R FIG. Key A 11,75 cm. minus 0,005 cm. (4.626 in. minus 0.002 in.) to Fig. 9 2,54 cm. FIG. R10 VERTICALTYPE OF BALANCING MACHINE WITH ADAPTER FOR SPIGOTTED WHEELS and Fig. 10 B Bore to give 0,051 mm. (0.002 in.) to 0,076 mm. (0.003 in.) clearance on spindle (1.00 in.)

  • Rolls-Royce Silver Shadow, Rolls-Royce Silver Shadow B Bentley T Series Workshop &nua/ 0 Chapter K FIG. K36 THROTTLE CONTROL LINKAGE-LATE L.H. DRIVE CARS A=2.265 in. to 2.300 in. (5,75 cm. to 5,84 cm.) B=18.575 in. (47,18 cm.) C=0.250 in. to 0.500 in. (0,63 cm. to 1,27 cm.) 1 'A' bank control shaft 2 Lever-'A' bank control shaft to control rod 3 Control rod-'A' bank manifold lever to fulcrum lever 4 Tie-rod 5 Fulcrum lever 6 Compensator link 7 Lever-ma

  • Rolls-Royce Silver Shadow & Bentlev T Series Workshop Manual Chapter IY 2. Remove the quadrant and lubricate the spindle with Ragosine 204G or equivalent grease. Refit the quadrant and finally tighten the 4 in. U.N.F. nut. 3. Do not overtighten the nut, since the bearing boss tends to spread slightly and a tight bearing may be formed. 4. Fit

  • Rolls-Royce Silver Shadow 6 Bentley T Series Workshop Manual Chapter N steady twisting pull to prevent jamming. If slight sticking occurs, carefully work the spool back into the valve body. If this does not free the spool it has become cocked in the valve body bore, and no attempt shouId be made to force the spool in or out. Con- tinue to dismantle

  • Rolls-Royce Silver Shadow, Workshop Manual Rolls- Royce Silver Shadow & Bentley T Series Chapter M FIG. M47 VOLTAGE REGULATOR & CURRENT REGULATOR SETTINGS 1 Cam 2 Contact A 1,32 mm. to 1,42 mm. (0.052 in. to 0.056 in.) Vohage and current regulator core gaps-To set 1. Using the special ' Lucas' tool (543-817-42), turn the adjustment cam anti-clockwise to the point giving minimum lift to the armature tensioning spring. 2. Slacken the adjustable contact locking nut and screw back the adiustable contact. 3.. Ins

  • Rolls-Royce Silver Shadow, Rolls-Royce Silver Shadow & Bentley T Series Workshop Manual Chapter M 4. Remove the two circular fresh air outlet control Interior lamp bulb-TO renew knob grub screws; remove the centre facia board. 1. Disconnect the battery. 5. Unscrew and remove the two screws securing the clock to the facia. 2. Remove the lamp bezel together with the lens; 6. Disconnect the cables from the terminals on the the unit is held in position with two spring clips. rear of the clock; withdraw the clock. 3. Renlove the bulb. Bulb renewal-Instrument and warning lamp 1. Disconnect the battery. 2. Remove

  • Rolls-Royce Silver Shadow, Rolls-Royce Silver Shadow 8 Bentley T Series Workshop Manual 7. Remove the three through bolts and spring washers and withdraw the DE shield complete with rotor. If 'Loctite' grade A has been used to secure the through bolts, local heat should be applied with a heated soldering iron to loosen them, the part should not be overheated. If necessary use a hide faced hammer and gently tap the DE shield away from the stator and SRE shield. Do not damage the slip ring when laying the DE shield and rotor assembly on the bench. Note The stator is sandwiched between the two end

  • Rolls-Royce Silver Shadow, Rolls-Royce Silver Shadow 8 Bent/ey T Series Workshop Manual Chapter ff Section N5 THE STEERING BOX (all cars) Introduction 3. Lubricate the rocking shaft bore and single lip A higher ratio steering box is now fitted to right-hand seal with power steering fluid. drive cars having the following number and onwards. 4. Fit the seal into the rocking shaft bore (see Fig. Standard cars 43154oachbuilt cars 5023. NB) using seal fitting tool (RH 7779). Do not drive The difference in ratio is as follows: the seal more than 4 in. (

  • Workshop Manual Rolls Royce Silver Shadow B Bentley T Series Chapter N 1 Filler cap 2 Spring 3 Pedestal stud 4 Filter 5 Filter support plate 6 Sealing ring 7 Clamping plate 8 Reservoir 9 Dowel 10 Banjo adaptor 11 Adaptor bolt 12 Sealing rings 13 Pump body 14 Bush 15 Oil seal 16 Bearing 17 Shaft 18 Pulley 19 Key 27 Roller 20 End plala 28 Seal

  • Rolls-Royce Silver Shadow, Workshop Manual Rolls Royce S~lver Shadow B Bentley T Series Chapter K tion is to draw air through the carbon, extracting the in order to extract the polyurethane foam filter fuel vapour as it does so for consumption in the engine. element. A detachable cover is situated in the left- The upper section of the canister is open to the atmos- hand valance, adjacent to the blower motor resistances phere and houses a polyurethane foam filter to ensure (see Fig. K40). that the air drawn through the carbon is clean. 1. Unscrew the four screws retaining the access cover, lift off the cover and withdraw the filter element Poly

  • Rolls-Royce Silver Shadow, Rolls- Royce Silver Shadow & Bentley T Series Workshop Manual Introduction The electrical system is negative earth. Electrical components not described within this chapter are given in the following list: Electric gear change actuator - Chapter T - Transmission Electric fuel pumps - Chapter K - Fuel System Air conditioning - Chapter C - e.g. Servo inodule, Air conditioning voltage stabiliser Exhaust emission control - Chapter U - e.g. Primary & secondary Emission C

  • - Workshop Manual Rolls Royce Silver Shadow 8 Bentley T Series FIG. K2 ARRANGEMENT OF THE FILLER TUBE ADAPTOR 1 Vent tube hoses 4 New filler tube adaptor 7 Filler cap 2 Convoluted hose 5 Upper fuel resistant hose 8 Worm drive clips 3 Adaptor for existing diameter 6 Filler tube 9 Spring clips vent pipe If an early type fuel tank is to be changed, the late

  • Rolls-Royce Silver Shadow, Rolls-fi~yce Silver Shadow & Bentley T Series Workshop Manual 0 Chaptt~r K FIG. K35 THROITLE CONTROL LINKAGE-LATE R.H. DRIVE CARS A=2-265 in. to 2.300 in. (5,75 cm. to 5.84 cm.) B=18.575 in. (47,18 cm.) inset 19.50 in. (50,OO cm.) C=0.250 in. to 0.500 in. (0,63 cm. to 1,27 cm.) 1 'A' bank control shaft 2 Lever-'A' bank control shaft to control rod 3 Control rod-'A' bank manifold lever to fulcrum lever 4 Tie-rod 5 Fulcrum lever 6 Compensator link 7 Lev

  • Rolls-Royce Silver Shadow, Workshop Manual Rolls Royce Silver Shadow 8 Bentley T Ser~es Chapter J The spring balance reading obtained to initially rotate the pinion will be high. It is the lower steady reading when the pinion is rotating, which indicates the pre:loading. 9. If the pre-load is not correct the pinion must be extracted from the housing and the adjusting washers changed as necessary to obtain the correct reading. Adjusting washers are available in a range from 0.105 in. to 0.110 in. (2,66 rnm. to 2,79 mm.) and 0.1 10 in. to 0.160 in. (2,79 mm. to 4,06 mm.)

Related Products and Documents (Automobile):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 S&S Cycle Air Cleaner Installation instructions manual s-s-cycle/air-cleaner-1S5.pdf 27 Feb 2024 8 1.24 Mb
2 GE Profile Arctica PSW26SGN Dimension manual ge/profile-arctica-psw26sgn-CT7.pdf 17 Jan 2023 3
3 Halton Capture Jet KVESJ Operator's manual halton/capture-jet-kvesj-8XS.pdf 20 Jun 2023 26
4 Agilent Technologies InfinityLab LC Series Operation & user’s manual agilent-technologies/infinitylab-lc-series-F92.pdf 10 Sep 2023 282
5 Zeus T1 Quick start manual zeus/t1-275.pdf 04 Dec 2023 2
6 Neopost DS-100 Product manual neopost/ds-100-219.pdf 07 Jul 2022 17

Similar Resources:

  • Tecumseh

    HHM80

    (8 pages)
    Page 1Figure 1MODEL3-1-99 181-630-14181-630-14ENGINES WHICH ARE CERTIFIED TO COMPLY WITH CALIFORNIAAND U.S. EPA EMISSION REGULATIONS FOR ULGE ENGINES, arecertified to operate on regular unleaded gasoline, include the followingemission control system(s): EM, TWC (if so equipped); Do not include anyuser adjustable features - therefore no other adjustments a …
  • Honda

    CIVIC Sedan

    (3 pages)
    Customized FeaturesBefore you customize settings, make sure that the vehicle is at a complete stopand shift to Park (P).Models with Color AudioModels with Display AudioVEHICLE CONTROLS …
  • Toyota

    Camry Hybrid 2013

    (510 pages)
    TABLE OF CONTENTS11Before drivingInformation on the hybrid system and adjusting and operating features such as door locks, mirrors, and steering column.2When drivingDriving, stopping and safe-driving information.3Interior fea-turesAir conditioning and audio systems, as well as other in-terior features for a comfortable driving experience.4Maintenance and car …
  • Isuzu

    RODEO

    (2613 pages)
    WORKSHOP MANUALRODEO(UE)FOREWORDThis manual includes special notes, important points, servicedata, precautions, etc. that are needed for the maintenance,adjustments, service, removal and installation of vehiclecomponents.All information, illustrations and specifications contained inthis manual are based on the latest product informationavailable at the time …
  • Suzuki

    GRAND VITARA -

    (518 pages)
    Table of Contents 1- i1Section 1CONTENTSEnginePrecautions .................................................1-1Precautions............................................................. 1-1Precautions for Engine.......................................... 1-1Engine General Information and Diagnosis ................................................. 1A-1Precautions …
  • Acura

    2008 RDX

    (434 pages)
    2008 RDXOwner’s Manual(Unlinked)This document does not contain hyperlinks and may be formatted for printing instead of web us. This is due to changes in content and specifications of the vehicle that happen throughout the model year. This manual will be replaced with a hyperlinked version at the end of the model year.© 2007 Honda Motor Co., Ltd. P/N 31S …

Comments, Questions and Opinions: