Manualios.com

Siemens AR6181-MX Installation And Configuration Manual

  • AR6181-MX Card Reader
  • ma71V1uyttdHs
  • Installation And Configuration Manual
  • PDF / Adobe Acrobat Reader
  • 52

Siemens AR6181-MX Manual Online:

3.55, 2875 votes
Siemens AR6181-MX User Manual
Siemens AR6181-MX User Guide
Siemens AR6181-MX Online Manual

Text of Siemens AR6181-MX User Guide:

  • Configuration parameters 10.2.7 ID number – BCD format RS485 – CerPass reader protocol The ID number / card number personalized in BCD format is transferred. DIP switch DIP1 . . DIP4 = reader address, DIP5 = 0, DIP6 = 1, DIP7 = 1, DIP8 = 1 Parameter: Transponder: ID_START, ID_LEN Direct: MF_BLOCK or MF_UL_Block or SL_BLOCK Indirect: MF_MAD, MF_AI

  • Siemens AR6181-MX, Installation Installation of the Square reader without distance frame For an installation without distance frame the gasket 1 has to be stuck on the back of the housing base. The position of the slits in the gasket has to correspond to the position of the screw holes in the housing. Fig. 5 Installation with gasket 1 Installation of the Square housing with distance frame For an installation with distance frame the gasket 1 is to be stuck on the back of this distance frame. The position of th

  • Configuration parameters C02 and C03 Wiegand format, data on ID card (ID number in Wiegand format) Wiegand-formatted data in conjunction with UCI reader protocol: WG_CODING 0x00 BCD-coded (4-bit) in reader protocol 0x01 ASCII-coded (7-bit) in reader protocol When transferring via Wiegand interface: WG_CD_ss 0x01 . . . 0x80 Start bit digit Wieg

  • Siemens AR6181-MX, Card reader configuration 2. Confirm by clicking on OK. Select the COM port. 3. Confirm by clicking on OK. Now select the following parameters: Bits per second 9600 Data bits 8 Parity None Stop bits 1 Flow control None 4. Confirm by clicking on OK. "HyperTerminal" has been started successfully. 26 Siemens Building Technologies Fire & Security Products 12.2004

  • Siemens AR6181-MX, Approval 1 Approval If used according to the instructions, this radio system meets the basic requirements of article 3 and the remaining applicable conditions of the R&TTE directive (1999/5/E6) of March 1999. Equipment Classification according to ETSI EN 300 330: Class 2 FCC ID: PJMCPR02 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference

  • Siemens AR6181-MX, Card reader configuration 9.3 Configuration mode of the Terminal program 1. Start the program "HyperTerminal." Please see chapter 9.2 Launching the terminal program. 2. Select "Properties" from the "File" menu.  The following dialog box opens: Select the following parameters on the "Settings" tab: 3. Click on .  The following dialog box opens: Specify the following parameters in the dialog box: 27 Siemens Building Technologies Fire & Security Products 12.2004

  • Configuration parameters 10 Configuration parameters 10.1 Config or ConfigCard parameters 0 1 2 3 4 5 6 7 8 9 10 11 12 13 CARD_TEC CONFIG _CARD C00 General 1 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x07 0x00 0x00 0x00 0x00 UCI_ Coding TAG- BEEP TAG- LED PIN_ MODE PIN_ BUF ID_ START ID_ LEN C01 General 2 0x00 0x00 0x00 0x02

  • Siemens AR6181-MX, Configuration parameters 10.4 Defining reading keys with Mifare Standard 1k and 4k The reading key is entered into the configuration file in line Kxx. For more information please refer to chapter 9.1 Defining parameters. 0 1 2 3 4 5 Mifare reading key no. 00 K00 Key00 0x00 0x00 0x00 0x00 0x00 0x00 Mifare reading key no. 01 K01 Key01 0xFF 0xFF 0xFF 0xFF 0xFF 0xFF Available Mifare key numbers: 00 ... 31 The shown table is an example: When using Mifare MAD addressing, the Mifare MAD access key has

  • Siemens AR6181-MX, Transponders / ID cards 8.3.2 ASCII format The ASCII format consists of alphanumerical values as defined in the ASCII (7-bit) table/rule. Depending on the output protocol, the individual characters can be transferred in two parts as a half byte. Configuration "UCI-CODING" = 0 ⇒ ASCII (default) The data stored on the ID card are max. 16 bytes (ASCII): "1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6" (ASCII) 31 32 33 34 35 36 37 38 39 30 31 32 33 34 36 (Hex) The length is defined with the parameters ID_START and ID_LEN. For more information please refer to chapter 10 under ID_START and ID_LEN. Data are transferred as: "1 2

  • Siemens AR6181-MX, Transponders / ID cards The block to be read can be addressed directly (e.g. by block number) or indirectly to the memory block of the transponder (e.g. in case of Mifare MifareApplicationDirectory). Access to a block with written data is to be set with the different configuration parameters of the card reader AR6181-MX. Parameters to access a personalized block:  Block address (for more information please refer to chapter 10 under SL_BLOCK ).  Access protection (see above)  Start and end of ID number in block (for more information please refer to chapter 8.3).  Form

  • Siemens AR6181-MX, Configuration parameters 10.2 Combination options 10.2.1 Serial number RS485 – CerPass reader protocol The unique serial number is transferred as a decimal equivalent. DIP switch DIP1 . . DIP4 = reader address, DIP5 = 0, DIP6 = 1, DIP7/DIP8 = 0 Parameter: Transponder: UID_OUT with UID_START, UID_LNG UID_MASK, UID_PATTERN PIN: PIN_MODE, PIN_BUF (default = 6) General: CARD_TEC, TAG_BEEP, TAG_LED, CONFIG_CARD Transferred: ID card data: 16 characters in ASCII format of which 13 are ID card number characters, aligned left, filled with zeros (0x30) – (telegram identifier: Kg) PIN: see Setting  PIN input CerPass reader prot

  • Siemens AR6181-MX, Liefermöglichkeiten und technische Änderungen vorbehalten. Data and design subject to change without notice. / Supply subject to availability. © 2004 Copyright by Siemens Building Technologies AG Wir behalten uns alle Rechte an diesem Dokument und an dem in ihm dargestellten Gegenstand vor. Der Empfänger anerkennt diese Rechte und wird dieses Dokument nicht ohne unsere vorgängige schriftliche Ermächtigung ganz oder teilweise Dritten zugänglich machen oder außerhalb des Zweckes verwenden, zu dem es ihm übergeben worden ist. We reserve all rights in this document and in the subject thereof

  • Siemens AR6181-MX, Appendix 11.4 Addressing / Address setting: Mifare 1k Block number (Hex) Sector Block Block number (Hex) Sector Block 0 ( 00 ) 0 0 24 ( 18 ) 8 0 1 ( 01 ) 0 1 25 ( 19 ) 8 1 2 ( 02 ) 0 2 26 ( 1A ) 8 2 3 ( 03 ) 1 0 27 ( 1B ) 9 0 4 ( 04 ) 1 1 28 ( 1C ) 9 1 5 ( 05 ) 1 2 29 ( 1D ) 9 2 6 ( 06 ) 2 0 30 ( 1E ) 10 0 7 ( 07 ) 2 1 31 ( 1F ) 10 1 8 ( 08 ) 2 2 32 ( 20 ) 10 2 9 ( 09 ) 3 0 33 ( 21 ) 11 0 10 ( 0A ) 3 1 34 ( 22 ) 11 1 11 ( 0B ) 3 2 35 ( 23 ) 11 2 12 ( 0C ) 4 0 36 ( 24 ) 12 0 13

  • Siemens AR6181-MX, Installation 6.4 Connecting the reader, display elements The reader is connected using the terminal board at the bottom section of the housing. Fig. 8 Terminal board Terminal Function Strip Description AR6181-MX/AR6182-MX card reader RS485 Bus Clock/Data interface Omron Wiegand X2 + / ~ Power supply - / ~ Power supply CLS *) CLS COM *) NO *) GND *) internal GND R/A RS485 - B T/B RS485 - A X1 CLK *) Clock D0 DAT *) Data D1 IN1 *) LED green, Buzzer short IN2

  • Siemens AR6181-MX, DIP switch settings 7.4 Information to be read out of cards According to the communication interface, the information to be read out of the access cards has to be selected. Important: Please ensure that the number of positions analysed and the format of the interface connected can be processed. DIP 7 DIP 8 Information to be read Card type off off Serial number ISO14443A+B, ISO15693 CerPass protocol (RS485) UID 13 characters card information, decimal equivalent, transmitted as a ASCII format UCI protocol (RS485) UID 13 digits card information, decimal equivalent, transmit

  • Siemens AR6181-MX, Card reader configuration Enter a name such as UPDATE into the name field and confirm by clicking on OK. 4. Select the COM port and confirm by clicking on OK.  The following dialog box opens: Now select the following parameters: Bits per second 38400 Data bits 8 Parity None Stop bits 1 Flow control None 5. Confirm by clicking on OK. 6. After pressing the Return key the following message is displayed: 7. Enter the command „FLASHALL“. 30 Siemens Building Technologies Fire & Security Products 12.2004

  • Siemens AR6181-MX, Technical specifications 5 Technical specifications Housing PC/ABS plastic Colour Top section of housing Similar to RAL 9006 (white aluminium) Bottom section of housing Similar to RAL 9006 (white aluminium) Weight Approx. 120 g Degree of protection IP 65 Power supply 12 to 24 V AC/DC Min. 10.2 V to max. 27.6 V Power consumption Max. 3 W Temperature range -20 to +60 °C Relative air humidity 95% (no dew formation) Antenna Integrated Operating frequency 13.56 MHz Qualified transponders ISO14443A: Mifare Standard 1k and 4k (UID, S/B, MAD), Mifare UltraLight (UID,

  • Siemens AR6181-MX, Card reader configuration 9.4 Reader interface The card readers AR6181-MX and AR6182-MX have to be connected via a RS485 bus interface, 2-wire, to the reader interface of the interface unit (e.g. DRI) or a door controller. For that a 4-wire, twisted pair, shielded cable is required. One pair is for the 2-wire RS485 party line and the other pair for power supply of the reader. The maximum allowed bus length is 1200 m (at 9600 Baud). The card readers AR618x-MX do have an Clock/Data interface which fulfils either the Omron (ABA format) / Magstripe Track II or the Wiegand interface re

  • Siemens AR6181-MX, Card reader configuration Note: When this command has been sent the reader must not be disconnected from the power supply.  This is acknowledged with the message "ERASE WAIT"  You are now prompted to send the firmware mhx file: "START DOWNLOAD". You have about 2 minutes to do this. During this period, the characters "C" and "§" will appear at intervals of 5 seconds. If no mhx file is sent within these 2 minutes, the message "ERROR 1" will appear and the command "FLASHALL" will have to be entered once more. Do not

  • Siemens AR6181-MX, Card reader configuration 4. Select "Send File" from the "Transfer" menu.  The following dialog box opens: Select the desired file, which you have edited. (Please see chapter 9.1 Defining parameters). 5. Click on the Open button.  The following dialog box opens: The data were then successfully loaded. 28 Siemens Building Technologies Fire & Security Products 12.2004

  • Siemens AR6181-MX, Appendix 11 Appendix 11.1 Definition of Clock/Data interfaces 11.1.1 Omron 5 bit, Magstripe Track II Signal diagram: Before and after data transmission there will be no output of clock pulses (clock, without data). 1010 t n t a t b /CLOCK /DATA /CLS t v t s 0 t n ≈ 1 ms t a(n) ≈ t n / 3 t b(n) ≈ t n / 2 t v = t s 10 ... 12 ms Structure of information: According to ISO7811-2 Track 2 (start sentinel, data, stop sentinel, LRC) Data format: 5 bit, (4 Data bits, 1 parity). 11.1.2 Wiegand Signal diagram: 45 /CLOCK = DATA0 /DATA = DATA1 / CLS t v

  • Siemens AR6181-MX, General notes 3 General notes The data transmission of the system from the user cards to the card readers is based on a electromagnetic field, which is created around the aerial of the card reader. If the ID card is approximated to the electromagnetic field of the reader aerial, it is supplied with energy and sends its personalised data. The data is received by the reader aerial. The reading range of the card readers AR618x-MX, depending on the kind of the arrangement and material the reader is mounted on, is up to 70 mm. The kind of transponder used (ID card, key fob, etc.) also has an important inf

  • Card reader configuration 9.1 Defining parameters Use an editor such as Notepad, for example, to define the Config or ConfigCard parameters. For more information about defining the configuration parameters C00-C06 please refer to chapter 10.1 Config or ConfigCard parameters. For more information about defining the reader keys Kxx please refer to chapter 10.4 Defining reading keys

  • Siemens AR6181-MX, Installation 6 Installation The reader is designed to be wall-mounted on 60 mm flush-mounting boxes. For surface mounting, the bottom section of the housing can be affixed to the distance frame supplied. Notes:  The reader should not be mounted directly onto conductive materials, such as metal surfaces, metal frames (reinforcement) or metal-plated surfaces, as these surfaces will reduce the reader's range. The clearance to such surfaces should be at least 30 cm.  If the unit has to be mounted onto a metal surface, the distance frame supplied can be used to maintain the minimum cle

  • Siemens AR6181-MX, Transponders / ID cards 8.1.3 ISO15693 Vicinity read range Type Manu- facturer UID UID lengt h (byte) Block Access block my-D vicinity (SRF55VxxP/S) Infineon ● 8 - - I-Code SLI Philips ● 8 - - Tag-IT HFI Texas Instruments ● 8 - - LRI512 STMicro- electronics ● 8 - - Structure of the UID (ISO15693) MSB LSB 64 57 56 49 48 . . . . . . . . . . . . . . . . . . . . . . . . . . 1 0xE0 MID SNR SNR: 48-bit (6 bytes) "IC manufacturer serial nu

  • Transponders / ID cards 8.2.1 Serial number The serial number is used as ID card number. The serial number is a unique number of a transponder or a transponder technology. The length of the serial number differs depending on the transponder technology. For more information please refer to chapter 8.1 Qualified transponder types (ID cards). The serial number stored in the tr

Related Products and Documents (Card Reader):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 Toshiba M5-S4332 Operation & user’s manual toshiba/m5-s4332-Y62.pdf 24 Jul 2022 244
2 Toshiba e-studio2007 Operation & user’s manual toshiba/e-studio2007-2EC.pdf 20 Mar 2024 170
3 LG LSB306 Owner's manual lg/lsb306-6E4.pdf 22 Mar 2024 26
4 IDTECH 2DScan FX100 Operation & user’s manual idtech/2dscan-fx100-8WA.pdf 10 Apr 2023 157
5 Panasonic PT-LB360 Spec file panasonic/pt-lb360-G9B.pdf 27 Dec 2022 8 0.78 Mb
6 BT CONVERSE 225 Operation & user’s manual bt/converse-225-1K7.pdf 26 Dec 2022 2 0.27 Mb

Similar Resources:

  • Delkin Devices

    eFilm Reader-18

    (12 pages)
    © Copyright Delkin Devices, Inc., All rights reserved. No part of this publicationmay be reproduced in any form, or by any means without prior written permissionof Delkin Devices, Inc.Printed in USA MNCA0031 • Rev 2.0Delkin Part No. DDREADER-18To prevent damage to the module or user, follow these basic handling guidelines• Do not drop, ben …
  • Cathodic Technology

    CorrReader

    (2 pages)
    Operation Manual for Stationary CorrReader Cathodic Technology Ltd. 15-1 Marconi Court Bolton, Ontario Canada L7E 1E2 Ph: ++1-905-857-1050 [email protected] www.cath-tech.com Stationary GPS Synchronized Test Station Reader CATH-TECH CORROSION CONTROL EQUIPMENT Operaon Power The Staonary CorrReader performs an inializaon sequence conrming …
  • Ingenico

    Moby/8500

    (10 pages)
    USER GUIDEUSER GUIDE IngenicoMoPhone:+1.88bileSolutions–88.589.5885–101FederalStt,7thFloorBosMobston,MA02110by/8500 …
  • OBID

    ID CPR.04.P/AB-USB

    (5 pages)
    MONTAGEINSTALLATIONID CPR04-Manual.DOC / 2006-12-21OBID® classic-proID CPR.04.P/AB-USBAnschluss und Inbetriebnahme Installation and starting upVielen Dank, dass Sie sich für den Kauf desID CPR.04.P/AB-USB entschieden haben.Der ID CPR.04.P/AB-USB ist als Desktop-Gerät fürden Office Einsatz konzipiert. Er sich für den berüh-rungslosen Datenaustausch mit …
  • Intuit

    QB21

    (2 pages)
    Index & Accessories (Fig.1) Bluetooth® Magstripe andEMV Card ReaderIntuit QB21Support Operating System:iOS, Android, Windows Phone 8, MS WindowsFor magstripe card readingFor EMV card readingMicro USB port forcharging operationLanyard holderPower buttonYou can follow your application instruction to start the transaction process, then swipe/insert card t …
  • Honeywell

    SPR-S8EZS

    (2 pages)
    32318170001 Rev.Bgetconnected.honeywell.com1.5mx3x312221121CR123 LITHIUM 3VCR123DURACELLWEBwww.www.www.TAGSPR-S8EZSAB231a1b4152341.5mx3x312221121CR123DURACELLWEBwww.www.1.5mx3x312221121CR123 LITHIUM 3VCR123DURACELLWEBwww.www.www.TAGSPR-S8EZSAB231a1b4152341.5mx3x312221121CR123DURACELLWEBwww.www.1.5mx3x312221121CR123 LITHIUM 3VCR123DURACELLWEBwww.www.www.TA …

Comments, Questions and Opinions: