ACTi KCM-8211 Hardware Manual

Text of ACTi KCM-8211 User Guide:

• ACTi KCM-8211, www.acti.com Hardware Manual 5 Safety Instructions Cleaning Disconnect this video product from the power supply before cleaning. Attachments Do not use attachments not recommended by the video product manufacturer as they may cause hazards. Do not use accessories not recommended by the manufacturer Only install this device in a dry place protected from weather. Servicing Do not attempt to service this video product yourself. Refer all servicing to qualified service personnel. Damage Requiring

• www.acti.com Hardware Manual 9 6) Power Button The power button is used to restart the camera. In case there is a need to restart the camera, press the power button (using a pointed object, such as a pen or pin). 7) Power LED The Power LED lights red when the camera is powered up. 8) Reset Button The reset button is used to restore the factory default settings of

• ACTi KCM-8211, www.acti.com Hardware Manual 3 Precautions Read these instructions You should read all the safety and operating instructions before using this product. Heed all warnings You must adhere to all the warnings on the product and in the instruction manual. Failure to follow the safety instructions given may directly endanger people, cause damage to the system or to other equipment. Servicing Do not attempt to service this video device yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel. Trademarks

• ACTi KCM-8211, www.acti.com Hardware Manual 10 Installation Step 1: Unpack the Camera 1. Remove the plastic cover. 2. Loosen the four screws using the allen wrench. 3. Carefully lift the camera cover and place it aside. Note: The cover is attached to the camera by a metallic wire; do not abruptly lift the cover. 4. Remove the styrofoam. Outer Styrofoam Inner Styrofoam

• ACTi KCM-8211, www.acti.com Hardware Manual 6 Introduction List of Models This hardware manual contains the following model: KCM-8211 2MP Outdoor PTZ Camera with D/N, Advanced WDR, SLLS, 18x Zoom lens

• www.acti.com Hardware Manual 27 Upon successful connection to the camera, the user interface called Web Configurator would appear together with the login page. The HTTP port number was not added behind the IP address since the default HTTP port of the camera is 80, which can be omitted from the address for convenience. B

• ACTi KCM-8211, www.acti.com Hardware Manual 14 How to Mount the Outdoor PTZ 1. Install the mounting solution Please refer to the installation guide that came with the mounting solution. 2. Insert the cable Insert the camera cables through the mounting tube (e.g. gooseneck, heavy wall mount, straight tube, extension tube, etc.) and through a hole in the wall or ceiling. CAUTION: The camera itself is waterproof, however take note that the cable connections are not. If the cable connections will be exposed outd

• www.acti.com Hardware Manual 15 Step 3: Connect the Equipment How to View the Camera on Your PC Perform the following connections to view the camera from your PC: 1. Connect the camera and the PC to the same network using Ethernet cables. 2. Connect the camera to a power supply using the supplied power adaptor and power cord. The Power LED of the camera will flas

• ACTi KCM-8211, www.acti.com Hardware Manual 22 Accessing the Camera Configure the IP Addresses In order to be able to communicate with the camera from your PC, both the camera and the PC have to be within the same network segment. In most cases, it means that they both should have very similar IP addresses, where only the last number of the IP address is different from each other. There are 2 different approaches to IP Address management in Local Area Networks – by DHCP Server or Manually. Using DHCP server to assign IP addresses If you have conn

• ACTi KCM-8211, www.acti.com Hardware Manual 16 Understanding the DI/DO Cables You can connect up to two DI and two DO devices to your camera. Device Cable Color Connection Digital Input 1 (DI1) Black Ground (GND) Red Digital Input 1 (DI1) Digital Input 2 (DI2) Yellow Ground (GND) Blue Digital Input 2 (DI2) Digital Output 1 (DO1) Brown 12V DC Orange Digital Output 1 (DO1) Digital Output 2 (DO2) Green 12V DC Purple Digital Output 2 (DO2) The table below shows the DI/DO connection specifications: Device DI Connection design TTL - compatibl

• ACTi KCM-8211, www.acti.com Hardware Manual 13 Vertical Pole Mount Suitable when mounting the Outdoor PTZ on a vertical pole. PAMX-0303 + PMAX-0503 PAMX-0305 + PMAX-0503 Horizontal Pole Mount Suitable when mounting the Outdoor PTZ on a horizontal pole. PAMX-0102 + PMAX-0503 Corner Mount Suitable when mounting the Outdoor PTZ on a corner wall. PAMX-0303 + PAMX-0402 PAMX-0305 + PAMX-0402 Other Mounting Accessories Accessories PMAX-0700 (Junction Box) PAMX-0104 (Extension Tubes)

• ACTi KCM-8211, www.acti.com Hardware Manual 17 Typical Connection Based on these specifications, if the DI device has a voltage of 0V ~ 30V or the DO device has a voltage of < 24V (<100mA), then the camera can supply internal power to these devices and there is no need to connect the DI/DO device to an external power source. In this case, use the Black (GND) and the Red (DI1) cables to connect a DI device and use the Brown (12V) and the Orange (DO1) cables to connect a DO device. See wiring scheme below: Consequently,

• ACTi KCM-8211, www.acti.com Hardware Manual 11 5. Attach the camera cover. Align the cover screws to the screw holes on the camera (as marked on the illustration) and secure the screws using the allen wrench.

• ACTi KCM-8211, www.acti.com Hardware Manual 18 High Voltage DO Device Connection Even though the camera provides 12V power, this may not be enough for some high voltage DO devices, such as a ceiling light or a motor that opens or closes a gate. In this case, there is a need to connect an external relay. See wiring scheme below: Note that when choosing an appropriate relay, please refer to its specifications and make sure they match the above design. The triggering circuit voltage has to be aroun

• ACTi KCM-8211, www.acti.com Hardware Manual 2 Table of Contents Precautions ............................................................. 3 Safety Instructions .................................................................................... 5 Introduction ............................................................. 6 List of Models ............................................................................................. 6 Package Contents ...................................................................................... 7 Physical Description ......

• ACTi KCM-8211, www.acti.com Hardware Manual 4 Federal Communications Commission Statement This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may

• www.acti.com Hardware Manual 20 2. From the network/power source side, insert the cables, such as the Ethernet cable, through a flex conduit with fitting (3/4”) (not included in the package) and through one of the holes of the junction box. Then connect the necessary cables. 3. Secure the flex conduit fitting onto the junction box hole. Note

• ACTi KCM-8211, www.acti.com Hardware Manual 19 Step 4: Waterproof the Cable Connections The camera itself is waterproof, however take note that the cable connections are not. If the camera is mounted directly on the wall where the cables pass through the wall, then your installation is complete and you do not need to waterproof the cable connections. However, if the camera is mounted where the cables may be exposed, such as when using the corner or pole mount or the pendant or gooseneck mount with brack

• ACTi KCM-8211, www.acti.com Hardware Manual 8 Physical Description 1) Audio Output This jack connects to an audio output device, such as a speaker. 2) DC 12V Power Input This jack connects to the power adaptor and power cord to supply power to the camera. 3) Audio Input This jack connects to an audio input device, such as a microphone with built-in amplifier. Note: Make sure that the connected audio input device has a built-in amplifier. Connecting an ordinary microphone will dwarf sounds and will result in inaudible recording. 4) Ethernet Port The Ethernet port connects to a n

• ACTi KCM-8211, www.acti.com Hardware Manual 7 Package Contents 1. Camera 2. Power Cord 3. Power Adaptor KCM-8211 4. Allen Wrench 5. Screws 6. Quick Installation Guide 7. Warranty Policy

• ACTi KCM-8211, www.acti.com Hardware Manual 12 Step 2: Mount the Camera Mounting Options There are several mounting options that you can use to install the Outdoor PTZ camera. For more information about mounting solutions and accessories, please refer to the Buyer’s Guide. Mount Types Accessories Pendant Mount Suitable when mounting the Outdoor PTZ on a hard ceiling. PMAX-0102 (Straight Tube w/o Bracket) PAMX-0103 (Straight Tube with Bracket) Straight Wall Mount Suitable when mounting the Outdoor PTZ on a straight wall. PMAX-0305 (Heavy Duty Wall Mount) PMAX-0302 (Gooseneck with Bracket) PMAX-0303 (Gooseneck without

More Instructions:

ACTi KCM-8211 Hardware manual 12-03-2024 38

DOWNLOAD

Related Products and Documents (Digital Camera):

Comparable Devices:

Similar Resources:

• Casio QV-70 (18 pages) LCD Digital CameraQV-70Owner’s Manual英PLAYLCDON/OFFRECPOWER/PROTECTZOOMDISPDELMODEON/OFF+–2IntroductionCongratulations upon your selection of the QV-70 LCD Digital Cam-era. The QV-70 comes with its own built-in liquid crystal color monitorthat let’s you instantly view the pictures you take.To get the most out of the QV-70, be sure to carefully read t …

• Canon EOS C100 (2 pages) EOS C100 DIGITAL VIDEO CAMERAKey FeaturesPROFESSIONAL PRODUCTSMass-Market Appeal• Canon Super 35mm CMOS Sensor• AVCHD Codec• Push Auto Iris/One-Shot AF• Three Built-In ND Filters• Canon Log Gamma• Canon Wide Dynamic Range (DR) Gamma• Fully compatible with all Canon EF, EF-S and EF Cinema Lenses• Dual SD Card Slots• 29 Custom Picture Settin …

• Canon PIXMA MX700 (32 pages) QT51386V01Network Setup GuideThis manual contains the setup information required to use the machine over wired LAN.If you use the machine with USB connection, refer to your setup sheet.IntroductionTo use the machine connected to a computer, you need to install the software called “MP Drivers” in the computer.The following two connection types are describ …

• Honeywell 2450Cm Series (2 pages) H2W2PER3 WDR 1080P IR Micro-Dome Camera Quick Installation Guide Thank you for purchasing a Honeywell Performance Series IP camera. Follow the instructions in this guide to install and log in to your camera. For instructions on configuring the camera, refer to the user guide on the CD that came with your camera. If you require additional assistance …

• Philips SPC300NC/37 (2 pages) For preview purpose onlySimply superior performance!Live video messagingIf you want to get into the fascinating world of face-to-face video chatting and video mails, the SPC 300NC is the smart way to get on-line and share the live action. It comes with everything you need, including v-mail software.High picture & video quality• 30 frames per second vid …

• Sanyo VPC-E1600TP (113 pages) 14 Mega PixelsDigital CameraINSTRUCTION MANUALVPC-E1600TPPlease read these instructions carefully before using the camera.Keep this manual in a safe place for later reference. …

Comments, Questions and Opinions: