Hitachi DV 14DSDL Service Manual
|
-1- Be sure to remove the storage battery from the main body before servicing. Inadvertent triggering of the switch with the storage battery connected poses the danger of the motor being accidentally turned on. 1. Precautions on disassembly and reassembly [Bold] numbers in the descriptions below correspond to item numbers in the Parts List and exploded assembly diagram for the Models DV 14DS
Hitachi DV 14DSDL, -10- 7. Mounting the drill chuck Mount Drill Chuck 13VLRL-N [2] to the spindle, and then tighten the Flat Hd. Screw (A) (Left Hand) M6 x 25 [1]. 8. Mounting hook Insert the Hook [43] into the groove at the lower portion on the side of the Housing (A).(B) Set [41],and then secure it by tightening the Truss Hd. Screw M4 (Black) [42]. Note that turning the Truss Hd. Screw M4 (Black) [42] too quickly may cause the Lock Nut M4 (Black) [44] in the housing to come off and become idle. Turn the Truss Hd. Screw M4 (Black) [42] slowly so that the Lock Nut M4 (Black) [44] is directed toward the Truss Hd. Screw M4 (Black) [42]. The Hook [43] can be attached on either side of the main unit.
Hitachi DV 14DSDL, -2- 5. Removal of the drill chuck and drive unit (1) Attach the spindle lock jig (an accessory of special repair tool J-355) to the spindle of Front Case [10], and then mount it in special repair tool J-355 clamped in the vise as illustrated in Fig. 1. (2) Turn the sleeve of Drill Chuck 13VLRL-N [2] counterclockwise (as viewed from the front) to fully open the jaws of Drill Chuck 13VLRL-N [2]. Turn the Flat Hd. Screw (A) (Left Hand) M6 x 25 [1] clockwise and remove it. (Note that this screw is left-hand threaded.) (3) Fit the h
Hitachi DV 14DSDL, -5- 2. Reassembly of the clutch unit (1) Mount the Stopper Spring [29], Stopper (A) [28], Sleeve [9], and Spring [8] to the Front Case [10] in this order (Fig. 4). (2) Screw the Nut [7] into the Front Case [10] (Fig. 5). Align mark (i) on the Nut [7] with mark (ii) on the Front Case [10], and then screw in the Nut [7]. Rotate the Nut [7] about a turn clockwise to align mark (i) on the Nut [7] with mark (ii) on the Front Case [10]. At this time, confirm that the “Y” surface of the Nut [7] is almost flush with the “Z” surface of the Front Case [10]. Fig. 4
Hitachi DV 14DSDL, -8- (2) Mount the Shift Knob [49] and Shift Arm [22] (Fig. 11). Mount the Shift Arm [22] to the cylindrical protrusions inside the Rear Case [21]. Insert the cylindrical protrusions of the Rear Case [21] into the holes of the Shift Arm [22] on both sides. Confirm that the protrusions of the Shift Arm [22] are properly inserted into the grooves of the Slide Ring Gear [27]. Then secure the Shift Arm [22] onto the Rear Case [21] by using the Screw Set D2 x 3.5 (2 pcs.) [23]. Insert the Shift Arm [22] inversely into the groo
Hitachi DV 14DSDL, -6- 3. Reassembly of the gear unit (1) Mount Washer (A) [13], Lock Ring (A) [14], and the Lock Cam [16] to the Front Case [10]. The protrusion of Lock Ring (A) [14] aligns with the concave portion of the Front Case [10] (Fig. 6). (2) Mount the Needle Roller Set (6 pcs.) [15]. NOTE : Apply grease (MOLUB-ARROY NO. 777-1) to the inner portion of Lock Ring (A) [14]. (3) Apply grease (Shell Alvania RL3) to the engaging portions of each gear, and the claw portion of the Ring Gear [19]. (4) Mount the parts from the Pin Set (6 pcs.) [12] to Washer (B) [34] in order (Fig. 7). • Pay attention to the needle mounting direction of the Ring Gear [19], Carrier [17], Slide R
Hitachi DV 14DSDL, Model DV 14DSDL CORDLESS IMPACT DRIVER DRILL LIST NO. J813 2012 · 1 · 12 (E1) 33 31 32 30 27 26 19 18 17 16 15 14 13 11 20 22 23 24 21 25 505 5 45 44 501 502 503 1 2 8 12 10 34 35 36 28 29 40 504 41 43 42 48 50 44 46 53 47 51 52 54 49 4 6 7 9 37 38 39 45 3
Hitachi DV 14DSDL, PART S DV 14DSDL DESCRIPTION REMARKS 51 313-687 TAPPING SCREW (W/FLANGE) D3 X 16 (BLACK) 11 52 NAME PLATE 1 53 306-952 STRAP (BLACK) 1 * 54 329-083 BATTERY BSL 1430 (EUROPE, AUS, NZL) 2 INCLUD. 505 * 54 334-419 BATTERY BSL 1440 (EUROPE, AUS, NZL) 2 INCLUD. 505 DESCRIPTION REMARKS 501 323-230 CASE 1 * 502 CHARGER (MODEL UC 18YRSL) 1 * 502 CHARGER (MODEL UC 18YML2) 1 503 983-006 + DRIVER BIT NO. 2 65L 1 504 331-906 SIDE HANDLE 1 505 329-897 BATTERY COVER 1 DESCRIPTION REMARKS 601 303-709 DEPTH GAUGE 1 1 - 12 - 3 - *ALTERNATIVE PARTS ST
Hitachi DV 14DSDL, -4- (3) When mounting the DC-Speed Control Switch [50] in housing (A), fit the protrusion of the forward/reverse changeover lever on top of the DC-Speed Control Switch [50] into the hole groove of the Pushing Button [48]. (4) Pass the internal wire connected to the LED light between the housing ribs as shown in Fig. 3. (5) Pass the internal wire connected to the DC-Speed Control Switch [50] between the ribs as shown in Fig. 3. (6) Bend the internal wire under the Controller Terminal Set [46] so that it fits in the housing. However, be careful not to break the internal wire when bending. Do not bend the internal wire toward the n
Hitachi DV 14DSDL, LIST No. DV 14DSDL: J813 DV 18DSDL: J815 Jan. 2012 PRODUCT NAME Hitachi 14.4 V Cordless Impact Driver Drill Model DV 14DSDL Hitachi 18 V Cordless Impact Driver Drill Model DV 18DSDL D International Sales Division REPAIR GUIDE ---------------------------------------------------------------------------------------------------------------- 1 1. Precautions on disassembly and reassembly ----------------------------------------------------------- 1 2. Precautions on disassembly and reassembly of battery charger ----------------------------------10 STANDARD REPAIR TIME (UNIT) SCHEDULES --------------------------------
Hitachi DV 14DSDL, PART S DV 18DSDL DESCRIPTION REMARKS 1 995-344 FLAT HD. SCREW (A) (LEFT HAND) M6 X 25 1 2 323-898 DRILL CHUCK 13VLRL-N (W/O CHUCK WRENCH) 1 3 334-473 TAPPING SCREW (W/SP. WASHER) D3 X 20 (BLACK) 4 4 334-444 COVER (A) 1 5 334-445 GEAR BOX ASS'Y 1 INCLUD. 6-35 6 334-446 DIAL HOLDER (B) 1 7 333-512 NUT 1 8 333-513 SPRING 1 9 333-514 SLEEVE 1 10 333-515 FRONT CASE 1 11 333-516 CLICK SPRING 1 12 333-539 PIN SET (6 PCS.) 6 13 331-909 WASHER (A) 1 14 331-903 LOCK RING (A) 1 15 331-888 NEEDLE ROLLER SET (6 PCS.) 6 16 331-904 LOCK CAM 1 17 333-517 CARRI
Model DV 18DSDL CORDLESS IMPACT DRIVER DRILL LIST NO. J815 2012 · 1 · 12 (E1) 33 31 32 30 27 26 19 18 17 16 15 14 13 11 20 22 23 24 21 25 505 5 45 44 501 502 503 1 2 8 12 10 34 35 36 28 29 40 504 41 43 42 48 50 44 46 53 47 51 52 54 49 4 6 7 9 37 38 39 45 3
Hitachi DV 14DSDL, -9- 6. Reassembly of the main unit (1) Mount the Lock Nut M4 (Black) [44] and Packing [45] to the Housing (A).(B) Set [41]. (2) Mount the power supply unit and drive unit that were reassembled in the procedure above to the Housing (A).(B) Set [41]. At this time, align the protrusions of the Front Case [10] and Motor Spacer [35] with the concave portions of the Housing (A).(B) Set [41]. (3) Mount the Pushing Button [48] into the Housing (A).(B) Set [41]. Confirm that the protrusion of the forward/reverse
Hitachi DV 14DSDL, PART S DV 14DSDL DESCRIPTION REMARKS 1 995-344 FLAT HD. SCREW (A) (LEFT HAND) M6 X 25 1 2 323-898 DRILL CHUCK 13VLRL-N (W/O CHUCK WRENCH) 1 3 334-473 TAPPING SCREW (W/SP. WASHER) D3 X 20 (BLACK) 4 4 334-444 COVER (A) 1 5 334-445 GEAR BOX ASS'Y 1 INCLUD. 6-35 6 334-446 DIAL HOLDER (B) 1 7 333-512 NUT 1 8 333-513 SPRING 1 9 333-514 SLEEVE 1 10 333-515 FRONT CASE 1 11 333-516 CLICK SPRING 1 12 333-539 PIN SET (6 PCS.) 6 13 331-909 WASHER (A) 1 14 331-903 LOCK RING (A) 1 15 331-888 NEEDLE ROLLER SET (6 PCS.) 6 16 331-904 LOCK CAM 1 17 333-517 CARRIER 1 18 333-518 PLANET GEAR (C) SET (5 PCS.) 5 19 333-519 RING GEAR 1 20
Hitachi DV 14DSDL, -7- 4. Reassembly of the armature unit (1) Mounting the Motor Spacer [35] Mount the Motor Spacer [35] to the Armature and Pinion Set [36]. If mounting proves too difficult, use a hand press to support the Motor Spacer [35] and press down on the rear end of the armature shaft of the Armature and Pinion Set [36] (Fig. 9). (2) Mounting the Magnet [37] Mount the Magnet [37] to the Armature and Pinion Set [36] so that the notch of the Magnet [37] faces the rear of the Armature and Pinion Set [36]. Hold each part securely as the Armature and Pinion Set [36] may be attracted to th
Hitachi DV 14DSDL, PART S DV 18DSDL DESCRIPTION REMARKS 51 313-687 TAPPING SCREW (W/FLANGE) D3 X 16 (BLACK) 11 52 NAME PLATE 1 53 306-952 STRAP (BLACK) 1 * 54 330-068 BATTERY BSL 1830 (EUROPE, AUS, NZL) 2 INCLUD. 505 * 54 334-421 BATTERY BSL 1840 (EUROPE, AUS, NZL) 2 INCLUD. 505 * 54 330-067 BATTERY BSL 1830 (USA, CAN) 2 INCLUD. 505 DESCRIPTION REMARKS 501 323-230 CASE 1 * 502 CHARGER (MODEL UC 18YRSL) 1 * 502 CHARGER (MODEL UC 18YML2) 1 503 983-006 + DRIVER BIT NO. 2 65L 1 504 331-906 SIDE HANDLE 1 505 329-897 BATTERY COVER 1 DESCRIPTION REMARK
-3- Reassembly can generally be conducted by reversing the disassembly procedure. However, special attention should be given to the following items. 1. Reassembly of the power supply unit Perform wiring according to the wiring diagram (Fig. 2). Pay attention to the direction in which to connect the internal wires and terminals. (1) Solder the internal wire (white) coming from the
DOWNLOAD |
Hitachi D13 Impact Driver Instruction manual
D13 |
Hitachi WH 14DSAL Impact Driver Handling instructions manual
WH 14DSAL |
Hitachi EC 10SB (SL) Impact Driver Instruction manual and safety instructions
EC 10SB (SL) |
Hitachi WR 14DH Impact Driver Technical data and service manual
WR 14DH |
Hitachi DV 20V2 Impact Driver Instruction manual
DV 20V2 |
Hitachi WH10DL - 10.8V Cordless Lithium Ion Micro Impact Driver Impact Driver Safety and instruction manual
WH10DL - 10.8V Cordless Lithium Ion Micro Impact Driver |
Hitachi WR 16SA S Impact Driver Handling instructions manual
WR 16SA S |
Hitachi WH 14 Impact Driver Instruction manual
WH 14 |
# | Manufacturer | Model | Document Type | File | Updated | Pages | Size |
---|---|---|---|---|---|---|---|
1 | Citizen | CBM-810 | Operation & user’s manual | citizen/cbm-810-18F.pdf | 03 Jan 2024 | 32 | 1.43 Mb |
2 | Alinco | DJ-X2 E | Instruction manual | alinco/dj-x2-e-UDH.pdf | 04 Jan 2023 | 48 | 0.38 Mb |
3 | Foxconn | H67MXV | Operation & user’s manual | foxconn/h67mxv-G72.pdf | 04 Sep 2022 | 109 | 5.81 Mb |
4 | Samsung | LNT4081F | Owner's instructions manual | samsung/lnt4081f-DZ6.pdf | 26 Dec 2022 | 283 | 53.09 Mb |
5 | Moen | S881 | Operation & user’s manual | moen/s881-471.pdf | 16 Nov 2022 | 6 | |
6 | Sony | MHS-FS3 | Specifications | sony/mhs-fs3-672.pdf | 03 Sep 2023 | 2 |
Makita
1 GB Cordless Impact Driver INSTRUCTION MANUAL UA Бездротовий ударний шуруповертІНСТРУКЦІЯ З ЕКСПЛУАТАЦІЇ PL Akumulatorowy Wkrętak Udarowy INSTRUKCJA OBSŁUGI RO Maşină de înşurubat cu impact cu acumulatorMANUAL DE INSTRUCŢIUNI DE Akku-Schlagschrauber BEDIENUNGSANLEITUNG HU Akkumulátoros ütvecsavar …
BTD136(68 pages) |
Makita
1 ENGLISH INSTRUCTION MANUAL DOUBLE INSULATION WARNING: For your personal safety, READ and UNDERSTAND before using. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE. Shear Wrench6924N 005843
…
6924N(8 pages) |
Milwaukee
OPERATOR'S MANUALMANUEL de L'UTILISATEURMANUAL del OPERADORTO REDUCE THE RISK OF INJURY, USER MUST READ OPERATOR'S MANUAL.AFIN DE RÉDUIRE LE RISQUE DE BLESSURES, L'UTILISATEUR DOIT LIRE LE MANUEL DE L'UTILISATEUR.PARA REDUCIR EL RIESGO DE LESIONES, EL USUARIO DEBE LEER EL MANUAL DEL OPERADOR.141012HEAVY-DUTY 12 V COMPACT DRIVERTOURN …
2401-20(10 pages) |
Gtech
OPERATING MANUALModel number: CID001Cordless Impact Driver4615_Impact_driver_manual_aw.indd 14615_Impact_driver_manual_aw.indd 1 28/10/2020 16:3828/10/2020 16:38
…
CID001(16 pages) |
Harbor Freight Tools
1/2” AIR IMPACTWRENCHASSEMBLY and OPERATINGINSTRUCTIONS3491 Mission Oaks Blvd., Camarillo, CA 93011Visit our Web site at http://www.harborfreight.comFor technical questions and replacement parts, please call 1-800-444-3353Model 02623®Copyright c 2002 by Harbor Freight Tools® . All rights reserved. No portion of thismanual or any artwork contained her …
02623(7 pages) |
Panasonic
© Panasonic Corporation 2015. All rights reserved.Unauthorized copying and distribution is a violationof law.ORDER NO. PTD1507X57CECordless Impact DriverModel No. EY75A7EuropeOceaniaTABLE OF CONTENTSPAGE PAGE1 Warning-------------------------------------------------------------- 22 Specifications ----------------------------------------------------- 23 Trou …
EY75A7(17 pages) |
IRiver MP3 Player H10 20GBMP3 Player #K1544T H10 20GB, 2 |
Panasonic Camcorder HX-DC10Panasonic Product Manual: HX-DC10 PDF Operating instructions manual - HWS2S7 HX-DC10, 179 |
Logik LED TV L24HED13L24HED13 (LED TV ePDF Guide, #K2M4G5) L24HED13, 2 |
Sixnet Modem VT-MODEMPDF User Guide (@ZCMZHR), Sixnet VT-MODEM Modem (13/09/2023) VT-MODEM, 30 |
Energenie Surge Protector EG-PMS2-WLANSurge Protector Operation & user’s manual (Energenie EG-PMS2-WLAN) EG-PMS2-WLAN, 67 |
HP Speakers 512n - Pavilion - 128 MB RAMHP Speakers Important safety instructions (File: hp-510n-pavilion-256-mb-ram-important-safety-instructions-1, 06/10/2023) 512n - Pavilion - 128 MB RAM, 1 |
Packard Bell Storage Grafite & CarbonDisassembly manual for Packard Bell Grafite & Carbon Storage Grafite & Carbon, 7 |
Elem Garden Technic Trimmer CBE25020PDF User Guide (@C79891), Elem Garden Technic CBE25020 Trimmer (20th Nov 2023) CBE25020, 35 |
JAMO Speakers S 506 HCS 3Speakers Specifications (JAMO S 506 HCS 3) S 506 HCS 3, 1 |
Makita Rotary Hammer HR5001CMakita HR5001C Rotary Hammer Instruction manual HR5001C, 24 |
HandHeld Touch terminals Transaction Team TT8500HandHeld Transaction Team TT8500 Touch terminals Startup manual Transaction Team TT8500, 68 |
Grandstream Networks IP Phone DP715#724PW2: DP715 IP Phone Configuration manual DP715, 6 |