Sekonic SR-3500 Operating Manual
|
Sekonic SR-3500, -29- Marking instructions Marks readable by this device are as follows. 1) Mark size: 0.5 x 3mm or more (standard mark) 2) Readable writing instruments: pencils (black, HB or darker), ballpoint pens (black or blue) 3) Readable marks: 4) Readable darkness: PCS 0.6 or darker Readable mark darkness can be adjusted. You can check mark darkness using a diagnostic utility included in the package, so check the darkness of the marks you want to read and adjust the reading setting. S e e “Data re
-4- Barcode readable area ................................................................................... 90 Barcode reading position adjustment .......................................................... 92 Barcode unit precautions for use .................................................................. 94 Cleaning ........................................
Sekonic SR-3500, -111- [Stacker unit] Error Explanation Code Solution Jam at printer printing start detection sensor A paper jam occurred at the printer printing start detection sensor. I1 • Remove jammed paper. • Press the CLEAR switch ( o r e x e c u t e th e cl e a r e r r o r command). Jam at main paper discharge sensor A paper jam occurred at the main paper discharge sensor. I2 • Remove jammed paper. • Press the CLEAR switch ( o r e x e c u t e th e cl e a r e r r o r command). Jam at selected paper discharge sensor A paper jam occurred at the sele c ted pa p er dis c harg e sensor. I3 • Remove
Sekonic SR-3500, -115- Timing control type If paper has pre-printed timing marks, the scanning area (reading area) of targeted mark frames will be determined by such timing marks. Timing control type is a method to determine the reading zone based on the timing mark width. Other methods include direct under type, mark to mark type, and FACOM type. Example: Timing control type to scan three times the timing mark width. Set multiple numbers using the software controlling OMR. ... ... ... ... Reading area N times the width of a timing mark Reading area N times the width of a timing mar
Sekonic SR-3500, -50- Stacker go out direction setting values • Main • Select Stacker settings (when stacker unit is installed) You can set the paper discharge direction in SR-600/SR-9000 mode. 1. Press the MENU switch to enter the menu mode. 2. Use the UP and DOWN switches to select the following parameters, and press the FEED/ENTER switch. 3. Select [Go Out Direction] setting and press the FEED/ENTER switch. (“ ” mark ashes in the rst column of the rst line on the L
Sekonic SR-3500, -78- 8. Close the front door of the stacker unit. Front door 9. Connect the power cord and turn the power on. 10. Execute printer test ( S e e P.70). * If the printing position is misaligned, adjust it. Fixing screw Cartridge case Positioning sticker Options Stacker unit Printing position adjustment
Sekonic SR-3500, -vii- [Mark to mark type card (0.25” IBM card size)] Standard size 187.32 0.2 A 0.2 A 0.2 A 82.55 0.8 9 or more Minimum 1 9 or more 3.5±0.1 Standard size General tolerance ±0.2 [Unit: mm] 6.35 x 11=69.85 Minimum 1.5 3.5-4.3 6.35 6.35 Should be in the center between timing marks Reading zone of second row Reading zone of first row 2.5 Appendix Sheet creation reference
Sekonic SR-3500, -51- Printer settings (when stacker unit or printer unit are installed) A character is 12 x 9 pixels. Though character height is xed (about 3mm), widths can vary. However, the number of pixels (9 pixels) does not change, so if you enlarge a character, the space between pixels increases, making the character appear lighter. Printer settings differ depending on the operating mode. 9 pixels 12 pixels Printer control You can set the device to either use the printer or not use it. If you
Sekonic SR-3500, -77- 5. Loosen the cartridge case xing screw, move the cartridge case according to the desired printing position, and tighten the screw to secure it. * The scale on the positioning sticker indicates the printing position from the edge of the paper. The printing position is determined by aligning the cartridge case xing screw with the scale on the sticker. Fixing screw Cartridge case Positioning sticker 6. If the printing position is properly aligned, install the printer in the stacker unit. 7. Tighten the printer xing screw and connect the printer connector. Fix
-13- Precautions For Use Handle the device with the following points in mind to enable full use of its functions. • Precautions regarding installation Do not place the device in the following places. Otherwise, failures could result such as paper jams, reading errors, or the unit could become inoperative. (1) In direct sunlight or near a heating de
Sekonic SR-3500, -89- Barcode unit / H (horizontal feeding) Reading direction Horizontal feeding (bar direction is perpendicular to sheet feeding direction) Codes JAN/EAN/UPC (module 0.33 mm,0.8 times~ 2 times) NW-7 ITF CODE-39 CODE-93 CODE-128 EAN-128 Reading area Sheet feeding direction: 12mm from the front edge of a sheet to 65mm from the rear edge of a sheet Paper width direction: 20mm from timing mark size to 224mm (centered on the sensor) Number of digits to be read Maximum 48 digits Number of labels to be read Maximum 10 (total numb
Sekonic SR-3500, -63- Displaying front side reading sensor settings This displays the settings for “sensor pitch” and “sensor type” for the front side reading unit in this device. 1. Press the MENU switch to enter the menu mode. 2. Use the UP and DOWN switches to select the following parameters, and press the FEED/ENTER switch. 3. Use the UP and DOWN switches to select [Type of Front Reading Sensor] display, and press the FEED/ENTER switch. 4. Use the UP and DOWN switches to display the settings.
Sekonic SR-3500, -56- Printer settings SR-600,SR-9000 mode 2. Character magnication setting Width can be magnied between 1 to 15 times. Character width = size x magnication (1) Press the MENU switch to enter the menu mode. (2) Use the UP and DOWN switches to select the following parameters, and press the FEED/ENTER switch. (3) Use the UP and DOWN switches to select [Magnication] setting, and press the FEED/ENTER switch. (“ ” mark ashes in the rst column of the rst line on the LCD.) (4) Use the UP
Sekonic SR-3500, -21- Operation Preparation (SR-3500) 1. Protecting tapes are attached to the main device in the following positions to protect it from vibration and shock during transportation. Remove the protecting tapes after placing the device in an appropriate location. 2. Install auxiliary brackets on the paper receiver. 3. Install the paper receiver on the main device. Hook tabs on the end of the paper receiver into the slits of the main device’s paper discharge side. auxiliary brackets paper receiver Protecting tapes Silica gel Protecting tapes Operation Preparat
-119- Mark to mark type If paper has pre-printed timing marks, the scanning area (reading area) of targeted mark frames will be determined by such timing marks. Mark to mark type is a method to read zones between two timing marks. Therefore, the number of timing marks in mark to mark type forms is always an even number. Other methods include timing control type, d
Sekonic SR-3500, -20- Product specications ( SR-6500 ) Sensor Reading Single sided, [double-sided] (* You need an optional back-surface reading unit for double-sided reading.) Darkness levels 16 levels (internal 256 levels) Light source color infra red light (940nm) [visible red light (660nm)] Pitch (inch) 1/6”, 0.2”, 0.25”, 0.3” Marking infra red light : pencil [visible red light : pencil, ballpoint pen (black or blue)] Reading marks size: 0.5×3mm
Sekonic SR-3500, -85- Printing position adjustment 1. Turn the power off and remove the power cord from the outlet. 2. Remove the carrier cover. Carrier cover 3. Loosen the cartridge case xing screw, move the cartridge case according to the desired printing position, and tighten the screw to secure it. * The scale on the positioning sticker indicates the printing position from the edge of the paper. The printing position is determined by aligning the cartridge case xing screw with the scale on the sticker. Fixing screw Cartridge case Positioning sticker 4. Connect the power cord and turn the power on. 5. Set printer control v
Sekonic SR-3500, -70- Printer test The test characters is printed on the fed sheet and the sheet will be discharged. (This test will be conducted only when stacker unit and printer unit are installed.) The number of characters printed varies depending on the printer settings, and character size and interval settings. Once reading of the check sheets starts, the test will continue until an error occurs or the hopper is empty. Test characters: “ !”#$%&’()*+,−./0123456789:;<=>?@ABCDEFGHIJKLMNOPQRSTUVWXYZ[¥]^_ �
Sekonic SR-3500, -i- Appendix Sheet creation reference You can use paper that you make yourself with this device in addition to the optional paper that we offer. If you make your own paper, follow the specications below. (1) Sheet size Height 110-335.6mm Width 63.5-228.6mm Do not cut or round the corners on the reference side (timing mark side). (See P.iv) (2) Weight and thickness (3) Paper quality OCR paper, quality paper, or recycled OCR paper. (4) Printing ink (printing surrounding mark elds) When the wavelength of the OMR reading sensor light source is 940nm, use spectrum band B900 to measure the PCS and use ink at PCS 0.15 or less. P
Sekonic SR-3500, -109- Error Explanation Code Solution Communication error Line error occurred between the device and the barcode unit. C1 None Internal com. error Barcode unit doesn't reply. C2 None Memory error Barcode unit memory error. C3 None Sensor error Error occurred with barcode sensor. C4 Download error Barcode unit download error. C5 None Internal erro Barcode unit internal error. C6 None Version error Barcode unit version does not correspond to the main body unit. C7 None Error Explanation Code Solution Communi
Sekonic SR-3500, -94- Barcode unit precautions for use (1) When applying barcode stickers, etc. on a sheet, make sure that sheet thickness with stickers is 0.25mm or less. (2) When applying barcode stickers, etc. on a sheet, avoid the grayed area below. (3) Make barcodes according to the following specications and guidelines. • AIM USS (Automatic Identication Manufacturers barcode symbol specications) • JIS JIS X 0501 Barcode symbols for common product codes JIS X 0502 Barcode symbols for logistic product codes J
-73- Stacker unit (printer) preparation 1. Turn the power off and remove the power cord from the outlet. 2. Open the front door of the stacker unit. Front door 3. Disconnect the printer connector. Connector Printer 4. Loosen the printer xing screw to remove it. Fixing screw Options Stacker unit Stacker unit preparation
Sekonic SR-3500, -110- (2) Transmission errors Error Explanation Code Solution Command error A non-specied command code was received. F4 Press the CLEAR switch (or execute the clear error command). Parameter error A non-specied parameter was received. F5 Press the CLEAR switch (or execute the clear error command). Protocol error While processing a command, another command was received. F6 Press the CLEAR switch (or execute the clear error command). (3) Cover open errors Error Explanation Code Solution Cover open The cover of the main body unit is open G1 Check if the cover of the main body unit is closed
Epson Stylus C42 All in One Printer Printer basics manual
Stylus C42 |
Brother IntelliFax-2840 All in One Printer Quick setup manual
IntelliFax-2840 |
Visioneer NETSCAN 4000 All in One Printer Specifications
NETSCAN 4000 |
Ricoh BizWorkz 106 All in One Printer Operation manual
BizWorkz 106 |
Intermec EasyCoder F4 All in One Printer Operation & user’s manual
EasyCoder F4 |
HP ENVY 100 e-All-in-One D410 series All in One Printer Operation & user’s manual
ENVY 100 e-All-in-One D410 series |
Epson Artisan 800 All in One Printer Operation & user’s manual
Artisan 800 |
Microtek ArtixScan 1800f All in One Printer Supplementary manual
ArtixScan 1800f |
# | Manufacturer | Model | Document Type | File | Updated | Pages | Size |
---|---|---|---|---|---|---|---|
1 | Teac | AI-2000 | Owner's manual | teac/ai-2000-YZD.pdf | 02 Jul 2023 | 36 | 0.68 Mb |
2 | JVC | CA-UXH10 | Bedienungsanleitung | jvc/ca-uxh10-CV7.pdf | 07 Aug 2022 | 72 | |
3 | EnGenius | EOC-2610 | Operation & user’s manual | engenius/eoc-2610-M23.pdf | 23 Mar 2023 | 9 | 0.2 Mb |
4 | Zanussi | ZCFF7/5W | Instruction booklet | zanussi/zcff7-5w-1E2.pdf | 20 Jun 2023 | 16 | 0.58 Mb |
5 | Sharp | HT-DV50U | Service manual | sharp/ht-dv50u-354.pdf | 31 May 2023 | 11 | 1.55 Mb |
6 | Escea | EF5000 | Installation manual | escea/ef5000-LT6.pdf | 14 Oct 2022 | 22 |
Xerox
111 2 3 4 52 3 4 5 6 7233 4 51 3 4 5242.3 kg93.3 lb.17.8 cm(7 in.)151.6 cm(59.6 in.)50 cm(19.7 in.)50 cm(19.7 in.)95.25 cm(37.5 in.)162.2 cm(63.8 in.)17.8 cm(7 in.)151.6 cm(59.6 in.)50 cm(19.7 in.)88.4 cm(34.8 in.)151.76 cm(59.75 in.)200.5 cm(78.9 in.) Xerox WorkCentre 4265Multifunction PrinterXerox® WorkCentre® 4265Installation Guide61Select LocationEN4In …
WorkCentre 4265(2 pages) |
Xerox
Xerox CopyCentre/WorkCentre 118Printer Kit Installation GuideGuide d'installation du kit imprimanteGuida all'installazione del kit stampanteInstallationsanleitung Drucker-KitGuía de instalación del kit de PostScriptGuia de Instalação do Kit da Impressora893E 18880MB3066Y6-1
…
C11 - DocuPrint Color Inkjet Printer(2 pages) |
Epson
EPSON Stylus PHOTO RX600/610 , RX620/630Scanner • Printer • CopierSERVICE MANUALSEOT03006Download Service Manual And Resetter Printer at http://printer1.blogspot.com
…
Stylus Photo RX600(106 pages) |
Kyocera
• 28 pages per minute with true 1,200 dpi resolution• Max. paper capacity of up to 800 sheets (incl. options)• Standard duplex unit for double-sided printing • Compact design, robust and reliable • Powerful controller with 32MB RAM as standard • Long-life componentsProduct depicted includes optional extrasThe Kyocera FS-1300D is the personalprint …
FS-1300D(2 pages) |
Panasonic
Please read these Operating Instructions before using the unit and save for future reference.This model is designed to be used only in the U.S.A.Operating Instructions2.4 GHz Cordless Phone Systemwith FAX and CopierModel No. KX-FG2451FOR FAX ADVANTAGE ASSISTANCE:— REFER TO www.panasonic.com/helpfaxfor customers in the U.S.A. or Puerto Rico— E-MAIL TO co …
KXFG2451 - B/W Thermal Transfer(76 pages) |
Xerox
XxxxxxxxXxxxxx653-01328B-MUL731-00991B-MUL Internal Quick ConnectGuideEnglish (EN)Français (FR)Italiano (IT)Deutsch (DE)Español (ES)Português (PB)Nederlands (NL)Svenska (SV)Norsk (NO)Suomi (FI)Dansk (DA)Português (PT)Türkçe (TR)Pycckий (RU)Creo Color Serverfor the Xerox Doc …
DocuColor 252(216 pages) |
Williams Sound Receiver Personal PA Receiver PPA R35-8Personal PA Receiver PPA R35-8 Instructions for use & care - 72Q37I Personal PA Receiver PPA R35-8, 2 |
Hunter Fan AstoriaAstoria (Fan ePDF User Manual, #YQMAXY) Astoria, 2 |
Makita Grinder 9005BMakita 9005B Grinder Instruction manual 9005B, 36 |
Psion Teklogix PDA Schnellstart- Anleitung 7525Psion Teklogix Product User Guide: Schnellstart- Anleitung 7525 PDF Operation & user’s manual - W22K35 Schnellstart- Anleitung 7525, 364 |
Toyota Automobile AVENSIS - SAutomobile Manual (Toyota AVENSIS - S) AVENSIS - S, 656 |
Graco Paint Sprayer 288844288844 (Paint Sprayer ePDF User Guide, #96NX7T) 288844, 36 |
Samsung VCR SV-647B/XEUPDF Guide (@9WKI48), Samsung SV-647B/XEU VCR (11th Jan 2024) SV-647B/XEU, 29 |
Indexa Handsets PENTATRON TF04MIndexa PENTATRON TF04M Guide (Operation & user’s manual), @OKWUL3 PENTATRON TF04M, 7 |
Sony Laptop VGN-CR490EBRUser Guide: Sony VGN-CR490EBR (H8DHR6, Upd.12.08.2023) VGN-CR490EBR, 2 |
Keithley Relays ERB-24Keithley Relays Operation & user’s manual (File: keithley-erb-24-operation-user-s-manual-33, Saturday 09-12-2023) ERB-24, 33 |
Simplicity Lawn Mower 1695163#9A4G76 1695163: Simplicity Lawn Mower Owner Documentation 1695163, 12 |
Trane Air Conditioner Voyager CommercialAir Conditioner PDF Manual Voyager Commercial, 92 |