Manualios.com

4RF Aprisa SR Operation & User’s Manual

4RF Aprisa SR Manual Online:

3.4, 2203 votes
4RF Aprisa SR User Manual
4RF Aprisa SR User Guide
4RF Aprisa SR Online Manual

Text of 4RF Aprisa SR User Guide:

  • 4RF Aprisa SR, Alarm Types and Sources | 373 Aprisa SR+ User Manual 1.5.3 Event ID Event Display Text Default Severity Configuration Type Function Recommended Actions 45 Port 3 Eth Data Receive Errors warning(4) Error Ratio Type Alarm to indicate that Ethernet port 3 received input signal contains errors at a higher rate than the defined error rate threshold. Check Ethernet cable and connector. Check switch port or RTU is active. Check IP and VLAN configuration. 46 Port 3 Eth Data Transmit Errors warning(4) Error Ratio Type Alarm to indicate that Ethernet port 3 transmitted output

  • 4RF Aprisa SR, Managing the Radio | 243 Aprisa SR+ User Manual 1.5.3 Monitoring > Serial This page displays the current radio performance monitoring parameters per serial port in packet and byte level granularity, for serial port high level statistics and troubleshooting. The results shown are since the page was opened and are updated automatically every 12 seconds. SERIAL PORT PARAMETERS All Serial Ports Monitored Parameter Function Normal Operating Limits Maximum Capacity Parameter to show the maximum serial data rate of the serial port

  • 4RF Aprisa SR, Managing the Radio | 237 Aprisa SR+ User Manual 1.5.3 Activation Date & Time This parameter sets the Date & Time when the software pack activation will occur. This setting can be any future date and 24 hour time. Skip Confirmation Step This parameter when enabled skips the confirmation step during the activation process. Normally, the confirmation step will require use intervention to accept the confirmation which will halt the activation process. Skipping the confirmation will enable the activation process to continue without use intervention. To activate software in remote stations: This process assumes that a So

  • 4RF Aprisa SR, About the Radio | 17 Aprisa SR+ User Manual 1.5.3 3. About the Radio The 4RF Aprisa SR+ Radio The 4RF Aprisa SR+ is a point-to-multipoint digital radio providing secure narrowband wireless data connectivity for SCADA, infrastructure and telemetry applications. The radios carry a combination of serial data and Ethernet data between the base station, repeater stations and remote stations. A single Aprisa SR+ is configurable as a point-to-multipoint base station, a remote station or a repeater station.

  • Product Options | 329 Aprisa SR+ User Manual 1.5.3 Protection Type All Protection Types Redundant Monitored Hot Standby Alarm Type Monitored on Active Radio Monitored on Standby Radio Monitored on Standby Radio TX Monitored on Standby Radio RX Modem FEC Disable     Modem ACM Lock     Alarm Inp

  • 4RF Aprisa SR, 222 | Managing the Radio Aprisa SR+ User Manual 1.5.3 Events > Defaults EVENT DEFAULTS Restore Defaults This parameter when activated restores all previously configured event parameters using ‘Events > Events Setup’ to the factory default settings.

  • 4RF Aprisa SR, Managing the Radio | 139 Aprisa SR+ User Manual 1.5.3 IP IP > IP Summary > Bridge / Gateway Router Modes This page displays the current settings for the Networking IP Settings for an Ethernet Operating Mode of ‘Bridge’ or ‘Gateway Router’. See ‘IP > IP Setup > Bridge / Gateway Router Modes’ on page 141 for configuration options.

  • Managing the Radio | 305 Aprisa SR+ User Manual 1.5.3 Transfer from Primary Unit 1. Select Transfer from Primary Unit. 2. Click on ‘Start Transfer’. 3. Go to ‘Protected Station: Software > Manager’ on page 306 to activate the Software Pack. The radio will reboot automatically. If the file transfer fails, check the Event History page (see ‘Protected S

  • 4RF Aprisa SR, Managing the Radio | 257 Aprisa SR+ User Manual 1.5.3 Monitoring > Address Tables ARP Table This page displays the current Address Resolution Protocols (ARP) on the radio. The radio implemented ARP protocol is used for resolution of network layer addresses into link layer addresses. It is used to map a IPv4 address to an Ethernet MAC address. The ARP table shows the results of the ARP protocol linkage between IPv4 address and Ethernet MAC address of the devices attached to the radio. In a layer 2 bridge LAN, an upper layer protocol may include the IP address of the destination, but since it is an Ethernet LAN network, it a

  • 4RF Aprisa SR, 310 | Managing the Radio Aprisa SR+ User Manual 1.5.3 Pause Transfer This parameter when activated, pauses the Over the Air Transfer Process and shows the distribution status. The distribution process will continue from where it was paused with Resume Transfer. Cancel Transfer This parameter when activated, cancels the Over the Air Transfer Process immediately. During the distribution process, it is possible to navigate away from this page and come back to it to check progress. The SuperVisor session will not

  • 4RF Aprisa SR, 196 | Managing the Radio Aprisa SR+ User Manual 1.5.3 Maintenance > General GENERAL Local Status Polling Period (sec) This parameter sets the rate at which SuperVisor refreshes the Local Radio alarm LED states and RSSI value. The default setting is 10 seconds. Network View Polling Period (sec) This parameter sets the rate at which SuperVisor polls all remote radios for status and alarm reporting. The default setting is 20 seconds. Remote Status Polling Period (sec) This parameter sets the rate at which SuperVisor refreshes the Remo

  • Managing the Radio | 151 Aprisa SR+ User Manual 1.5.3 PRIORITY DEFINITIONS PCP (Priority Code Point) These settings provide priority translation / mapping between the external radio LAN VLAN priority network and the radio internal VLAN priority network, using the VLAN tagged PCP (Priority Code Point) priority field in the Ethern

  • 4RF Aprisa SR, Managing the Radio | 225 Aprisa SR+ User Manual 1.5.3 FILE TRANSFER Transfer Activity This parameter shows the status of the transfer, ‘Idle’, ‘In Progress’ or ‘Completed’. Method This parameter shows the file transfer method. When the software distribution is in progress, this parameter will change to ‘Over the Air’ (from xx.xx.xx.xx) to show that the interface is busy and the transfer is in progress. File This parameter shows the software file source. Transfer Result This parameter shows the pr

  • 4RF Aprisa SR, Specifications | 393 Aprisa SR+ User Manual 1.5.3 Power Specifications Power Supply Aprisa SR+ Radio Nominal voltage +13.8 VDC (negative earth) Absolute input voltage range +10 to +30 VDC Maximum power input 35 W Connector Molex 2 pin male screw fitting 39526-4002 Aprisa SR+ Protected Station Power Input 13.8 VDC 48 VDC Nominal voltage +13.8 VDC (negative earth) 48 VDC (floating) Absolute input voltage range +10 to +30 VDC 18 to 60 VDC Maximum power input 42 W Connector 2x Mole

  • Maintenance | 365 Aprisa SR+ User Manual 1.5.3 USB Boot Upgrade Method A single Aprisa SR+ radio can also be upgraded simply by plugging a USB flash drive containing the new software into the USB A host port on the Aprisa SR+ front panel and power cycling the radio. To upgrade the Aprisa SR+ radio software: 1. Unzip the software relea

  • 4RF Aprisa SR, Managing the Radio | 229 Aprisa SR+ User Manual 1.5.3 To transfer software into the Aprisa SR+ radio: USB Transfer Method 1. Unzip the software release files in to the root directory of a USB flash drive. 2. Insert the USB flash drive into the host port . 3. Click on ‘Start Transfer’. 4. When the transfer is completed, remove the USB flash drive from the host port. If the SuperVisor ‘USB Boot Upgrade’ setting is set to ‘Disabled’ (see ‘USB Boot Upgrade’ on page 226), the USB flash drive doesn’t need to be removed as the radio won’t try to load from it.

  • 4RF Aprisa SR, Index | 401 Aprisa SR+ User Manual 1.5.3 S security settings171, 182, 187, 189, 210, 216, 218, 220, 222 summary 170, 184, 282 security users user privileges 180 SuperVisor logging into 75 logging out 76 PC requirements for 68 PC settings for 71 T temperature 56 tools 58 U users adding 180 changing passwords 181 deleting 181 user details 180 user privilege 181 W WEEE 397

  • 38 | About the Radio Aprisa SR+ User Manual 1.5.3 Avoiding Narrow Band Radio Traffic Overloading The Aprisa SR+ supports mechanisms to prevent narrowband radio network overload: 1. L3/L4 Filtering The L3 filtering can be used to block undesired traffic from being transferred on the narrow band channel, occupying the channel and risking the SCADA critical traffic. L3/4 filte

  • Managing the Radio | 117 Aprisa SR+ User Manual 1.5.3 Serial Packet Time to Live (ms) This parameter sets the time a serial packet is allowed to live in the system before being dropped if it cannot be transmitted over the air. The default setting is 800 ms. Ethernet Packet Time to Live (ms) This parameter sets the time an Ethernet packet is allo

  • 4RF Aprisa SR, Managing the Radio | 113 Aprisa SR+ User Manual 1.5.3 Serial Data Stream Mode This parameter controls the traffic flow in the radio serial ports. Option Function Broadcast Serial port traffic from the network is broadcast on all serial ports on this radio. This will include the RS-232 port derived from the USB port. Segregate Serial port traffic from the network from a specific port number is directed to the respective serial port only (see Segregated Port Directions). The default setting is Broadcast. Segregat

  • 4RF Aprisa SR, 94 | Managing the Radio Aprisa SR+ User Manual 1.5.3 Terminal > Operating Mode OPERATING MODES Terminal Operating Mode The Terminal Operating Mode can be set to Base, Base Repeater, Repeater or Remote station. The default setting is Remote. Option Function Base The base station manages all traffic activity between itself, repeaters and remotes. It is the center-point of network where in most cases will be connected to a SCADA master. Base Repeater The base-repeater has the same function as the base station (and repeater station), but used when peer to peer connections between remotes is required via the base station.

  • 4RF Aprisa SR, Managing the Radio | 279 Aprisa SR+ User Manual 1.5.3 Protected Station: IP > IP Setup This page provides the setup for the Protected Station Networking IP setup. NETWORKING IP SETTINGS Changes in these parameters are automatically changed in the partner radio. Primary IP Address Set the static IP Address of the primary radio assigned by your site network administrator using the standard format xxx.xxx.xxx.xxx. The default IP address is in the range 169.254.50.10. Secondary IP Address Set the static IP Address of the secondary radio assigned by your site network administrator using the standard format xxx.xxx.xxx.xxx. The

  • 4RF Aprisa SR, 4 | Aprisa SR+ User Manual 1.5.3 Compliance Industry Canada The Aprisa SR+ radio is designed to comply with Industry Canada (IC) specifications as follows: Radio RSS-119 / RSS-134 EMC This Class A digital apparatus complies with Canadian standard ICES-003. Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada. Environmental EN 300 019, Class 3.4 Ingress Protection IP51 Safety EN 60950-1:2006 Class 1 division 2 for hazardous locations

  • 4RF Aprisa SR, About the Radio | 39 Aprisa SR+ User Manual 1.5.3 5. Ethernet Data and Management Priority and Background Bulk Data Transfer Rate Alternatively to VLAN priority, users can control the Ethernet traffic priority (vs serial), management priority and rate in order to control the traffic load of the radio network, where important and high priority data (SCADA) will pass-through first assuring SCADA network operation. The user can set the use of the Etherne

  • 4RF Aprisa SR, Managing the Radio | 291 Aprisa SR+ User Manual 1.5.3 Protected Station: Maintenance > MMS This screen applies when the terminal is a Migration Master Station. MMS NETWORK MANUAL LOCK The MMS network manual lock controls the switching of the Migration Master Station. Lock Type This parameter sets the Migration Master Station manual lock. Option Function Disable Disables manual locking of the Migration Switch i.e. allows for automatic switching. Enable Allows the Migration Switch to be manually locked i.e. disables automatic switching. Timer Allows the Migration Switch to be manually locked but only for a predetermined p

  • 4RF Aprisa SR, 234 | Managing the Radio Aprisa SR+ User Manual 1.5.3 Software > Remote Distribution This page provides the mechanism to distribute software to all remote stations into the Aprisa SR+ network (network) and then activate it. The Software Pack that was loaded into the base station with the file transfer process (see ‘Software > File Transfer’ on page 227) can be distributed via the radio link to all remote stations. This page is used to manage the distribution of that software pack to all remote radios on the network. This page is only available when the radio is con

  • 4RF Aprisa SR, Managing the Radio | 135 Aprisa SR+ User Manual 1.5.3 Double Tag Egress S-VLAN Priority This parameter sets the S-VLAN egress traffic priority. The default is Priority 1 (Best Effort). Option Egress Priority Classification High / Low Priority Priority 0 Background 0 Lowest Priority Priority 1 (Best Effort) 1 Priority 2 (Excellent Effort) 2 Priority 3 (Critical Applications) 3 Priority 4 (Video) 4 Priority 5 (Voice) 5 Priority 6 (Internetwork Control) 6 Priority 7 (Network Control) 7 Highest Priority

Related Products and Documents (Radio):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 Canon imageCLASS MF7470 Specification canon/imageclass-mf7470-9EW.pdf 28 Sep 2023 4 2.34 Mb
2 Sony CFD-F10L Manual del instrucción sony/cfd-f10l-38M.pdf 08 Nov 2022 2 0.14 Mb
3 Fender Telecaster Thinline Parts list fender/telecaster-thinline-S45.pdf 10 Oct 2023 1 0.02 Mb
4 Carrier 30GX080-265 Controls, start-up, operation, service, and troubleshooting carrier/30gx080-265-B1S.pdf 11 Sep 2023 100
5 Emerson CK5048 Owner's manual emerson/ck5048-U6L.pdf 22 Dec 2023 19 0.25 Mb
6 Olympus WS-801 Operation instruction manual olympus/ws-801-41T.pdf 29 Mar 2023 95

Similar Resources:

  • Makita

    DMR108N

    (108 pages)
    DMR108N EN Job Site Radio Instruction manual 5FR Radio de chantier Manuel d’instructions 15DE Baustellenradio Betriebsanleitung 26IT Radio da cantiere Manuale delle Istruzioni 36NL Bouwradio Gebruiksaanwijzing 46ES Radio de Trabajo Manual de instrucciones 56PT Rádio a Bateria Manual de instruções 67DA Byggepladsradio Instruktionsmanual 77EL Ραδιόφ …
  • Ritron

    JBS-146D

    (25 pages)
    Have questions? Call 800-USA-1-USA (800-872-1872) or visit our website at www.ritron.com page 1 Display-Series Two-Way Base Station Owner’s Manual RUGGED, PROFESSIONAL TWO-WAY BASE RADIOS ALWAYS THERE…ALWAYS READY…ALWAYS ON SM • 77 UHF and 26 VHF Table Frequencies for Easy Field Programming • Built-in Quiet Call ® and Digital Quiet Cal …
  • Craftsman

    UNIVERSAL RECEIVER 139.18152

    (2 pages)
    Universal ReceiverModel 139.18152USER INSTRUCTIONSNOTICE: To comply with FCC and or Industry Canada (IC) rules, adjustment or modifications of thisreceiver and/or transmitter are prohibited, except for changing the code setting or replacing thebattery. THERE ARE NO OTHER USER SERVICEABLE PARTS.Tested to Comply with FCC Standards FOR HOME OR OFFICE USE. Opera …
  • AirLive

    AirMax DUO Lite

    (2 pages)
    PowerDeclaration of ConformityRegulatory ApprovalsWe, Manufacturer/ImporterDeclare that the product802.11 a/b/g Dual Radio Base StationAirLive AirMax DUO Liteis in conformity withIn accordance with 2004/108/ EEC-EMC Directive and 1999/5 EC-R & TTE DirectiveClauseManufacturer/ImporterDescriptionOvisLink Corp.5F, NO.6, LANE 130, MIN-CHUAN RD.,HSIN-TIEN DIS …
  • Banner

    Sure Cross MultiHop H3E-NB-KR

    (8 pages)
    DatasheetThe Sure Cross® wireless system is a radio frequency network with integrated I/O that operates in most environments to eliminate the need forwiring runs. Wireless MultiHop data radio networks are formed around a MultiHop master and one or more slaves and extend the range of a Modbusor other serial communication network.• Wireless industrial I/O d …
  • Creative

    WP-300

    (6 pages)
    Creative WP-300 User Manual.(Model number EF0450) Illustration1 Illustration2Thank you for selecting Creative’s PURE WIRELESS Headphones. This documentation aims to guide you inmaking full use of the headphones. Fully charge the headphones before first use. Then you need to “pair”the headphones once with your Bluetooth audio device before …

Comments, Questions and Opinions: