Aiphone JKW-IP Operation Manual
|
AIPHONE CO., LTD., NAGOYA, JAPAN AIPHONE CORPORATION, BELLEVUE, WA, USA AIPHONE S.A.S., LISSES-EVRY, FRANCE http://www.aiphone.net/ Warranty Aiphone warrants thats its products have no material or workmanship defects under normal use conditions for two years after delivery to the end user. Aiphone will perform repair or replacement free of charge if the product is defective and th
18 19 IP Video Intercom Adaptor Settings Enter a valid ID and Password. If you enter the ID and Password here, you will not have to enter them again when logging into the IP Video Intercom Adaptor. MEMO For provisional registration and for the Administrator, enter "aiphone" as the ID, and "aiphone" as the Password. If they are not entered correctly, an ID
Aiphone JKW-IP, 36 37 PC Application Settings Event Notification Operation List Setting Description Reference Maximize Application When there is a call from (one of) the door station(s), or when Sensor Detection occurs (even when minimized), the PC Application is automatically maximized. Balloon Notification When there is a call from (one of) the door station(s), or when Sensor Detection occurs, a Balloon Notification appears. P.45 Sensor Detection Tone When a sensor connected to the IP Video Intercom
Aiphone JKW-IP, 22 IP Video Intercom Adaptor Settings 23 Enter a password in New Password. You can enter up to 16 single-byte alphanumeric characters for the password. Enter the new password again in the "Re-type" field as confirmation. Click [SAVE]. "[Administrator Registration] Setting has been saved." is displayed, the entered ID and new password are set, and you are returned to the Administrator Settings window. When you have changed the ID or password Change the ID or password in "Registering the IP Video Intercom Adaptor" P.18 to the same ID or password. MEMO Setting operations are canceled if you click [CANCEL], and you are returned to
Aiphone JKW-IP, 40 41 PC Application Basic Operations 5-1-3 Zoom/Wide, Pan & Tilt By using the following steps, the monitor screen of the PC Application can be switched between a wide picture and a zoom picture. Calling from the door station Entrance monitoring Communicating with the door station By using Pan & Tilt when a zoom picture is displayed, a wide picture can be split into 9 images and displayed as 1 picture. MEMO If the door station is operated from another PC Application or a master monitor station at the same time as Zoom/Wide or Pan & Tilt, the operation may not be enabled, due to communication over
54 55 For Global IP Video Intercom Adaptor Broadband router �
32 IP Video Intercom Adaptor Settings 33 3-4 User Settings Registration : Administrator/User User Settings for the PC Application can be made from the User Settings window while logged in as the Administrator or a User. 3-4-1 Downloading Encryption Key To use the Door release and Option Output with the PC Application, you need to obtain the Encryption Key F
Aiphone JKW-IP, 22 23 IP Video Intercom Adaptor Settings Click [SAVE]. "[User Registration] Setting has been saved." is displayed, and you are returned to the Administrator Settings window. MEMO Setting operations are canceled if you click [CANCEL], and you are returned to the Administrator Settings window. All settings are returned to their factory default settings if you press the IP Video Intercom Adaptor default setting switch for 5 seconds or more. • • 3. ・ 3-3-3 Email Setting (IP Video Intercom Adaptor) In Email Setting, you can set inform
Aiphone JKW-IP, 14 INTRODUCTION 15 Click [Next]. The Select Installation Folder window is displayed. Click [Next]. The folder in which the application is to be installed is created. Click [Next]. Installation begins. 5. ・ 6. ・ 7. ・ When the installation is complete, the Select Recording File Storage Folder (Browse for Folder) window is displayed. Select the folder where you want to save recorded files, and then click [OK]. The selected folder becomes the storage location for recorded files. After it is selected, the saved location cannot be changed. Click [Close]. Installa
Aiphone JKW-IP, 30 IP Video Intercom Adaptor Settings 31 Firmware Update To update the IP Video Intercom Adaptor firmware, you need to set the PC as a server beforehand and then save the firmware to be updated on the server. You may also need to turn off the Windows Firewall and security software functions. Setting up an FTP Server Select "Add or Remove Programs" from the computer's "Control Panel", and then click "Add/Remove Windows Components". Select "Internet Information Services (IIS)&
Aiphone JKW-IP, 42 43 PC Application Basic Operations Calling / communicating with the master monitor station If you want to call a master monitor station from the PC Application, you can choose to call all master monitor stations in the system, or call one specific master monitor station. From the "Adaptor" display ( j ) in the Expanded Window, select the master monitor station-connected IP Video Intercom Adaptor you want to call. 1 When calling all master monitor stations in the system, do not select any Adaptors. If an Adaptor is selected, you can release it by clicking it again. MEMO You cannot select specific multiple Adaptors. You can select "One Adaptor" or &
2 3 CONTENTS 1 1-1 1-2 1-3 1-4 1-5 2 2-1 2-2 3 3-1 3-2 3-3 3-4 4 4-1 5 5-1 5-2 5-3 5-4 6 INTRODUCTION .......................... 6 System Configuration Example ....... 6 Names ............................................ 7 IP Video Intercom Adaptor ..........................7 PC Application Window ...............................8 About System Settings .......
Aiphone JKW-IP, 16 Network Settings 17 2-2 Connecting the PC of the person setting up the network and the IP Video Intercom Adaptor Provisional registration In order to configure the IP Video Intercom Adaptor, use a LAN cable and connect the PC of the person setting up the network and the IP Video Intercom Adaptor. When connecting the PC of the person setting up the network directly to the IP Video Intercom Adaptor, use an Ethernet crossover cable. When connecting via a hub, use a straight cable. Even if it is to be used wi
Aiphone JKW-IP, 32 33 IP Video Intercom Adaptor Settings Select the Encryption Key File corresponding to the selected "Adaptor". Click [SAVE]. The Encryption Key is set, and you are returned to the Expanded Window. MEMO Setting operations are canceled if you click [CANCEL], and you are returned to the Expanded Window. • When the Encryption Key setup is complete, the icon in the [Status] column changes from gray to blue. Carry out 1. to 7. for all IP Video Intercom Adaptors connected to the system. MEMO If the Encryption
Aiphone JKW-IP, 6 7 INTRODUCTION 1-2 Names S1 E S2 E S3 E S4 E RY RY B1 B2 DC18V POWER ON OFF + - POWER AIPHONE JKW-IP STATUS LAN ACT STRIP LENGTH LAN 11mm Ø0.65∼Ø1.2 IP Video Intercom Adaptor POWER indicator (Green) Lit green when the power is on. STATUS indicator (Orange) Blinks orange while the system starts up, and remains lit once startup is complete. LAN ACT indicator (Orange) Lit orange when a LAN is connected, and blinks while exchanging information over the Ethernet. Default setting switch (within the sticker area) When pressed for 5 seconds or more, IP V
Aiphone JKW-IP, 4 5 We will under no conditions be liable for damage that occurs due to failures in network equipment; failures due to internet providers and cell phone companies; failures such as disconnected lines and other losses in communication, which render it impossible to provide this service or in any way delay this service due to causes outside of our responsibility; or if an error or missing data occurs during transmission. We will under no conditions be liable for damage that occurs due to the inability to communicate due to malfunctions, problems, or
Aiphone JKW-IP, 52 53 Technical Precautions Cleaning: Clean the units with a soft cloth dampened with a neutral household cleanser. Do not use an abrasive cleanser or cloth. If you are experiencing difficulties with the device such as "Settings not working well", please check our homepage at http:// www.aiphone.net/. ・ ・ Specifications Item Description Power DC18 V Current consumption Standby 110 mA, Maximum 200 mA Communication Hands-free / Priority transmission Image Format JPEG Image Resolution 320×240 (QVGA) Network Interface 10BASE-T/100BASE-TX Ethernet Protocol TCP/IP, UDP/IP, SIP Environment Bandwidth 320 K to 8 Mbps (per IP Video
Aiphone JKW-IP, 12 13 INTRODUCTION 1-5-2 Installing This section describes how to install the PC Application into your PC. The screens may differ depending on the OS. Follow the on-screen instructions to install. Insert the CD-ROM into your computer. Operation Manual & Software (CD-ROM) Click "English" on the language selection screen. Click "PC Application", and then follow the on-screen instructions to install. The Aiphone_JKW Setup Wizard window is displayed. • • 1. 2. 3. ・ If ".NET Framework" is not already installed, the .NET Framework installation window is displayed. Follow the on- screen instructions to instal
Aiphone JKW-IP, 36 PC Application Settings 37 Click [SAVE]. The Volumes are set and the PC Application Settings window closes. MEMO Setting operations are canceled if you click [CANCEL], and the PC Application Settings window closes. The Microphone Volume and Speaker Volume settings are synchronized with the computer's settings. For more information, see the Operation Manual supplied with your computer. Click [ ? ] to display a help pop-up window. • • • 2. ・ 4-1-2 Preferences Settings To adjust the Preferences Settings, click the "Preferences" tab from the PC Applications Settings window to display the settings screen. The f
Aiphone JKW-IP, 14 15 INTRODUCTION 1-5-3 Uninstalling From the Windows "start" menu, select "Control Panel" " "Add or Remove Programs", and select "Aiphone_JKW" to delete it. MEMO With Windows 7, the PC Application may still remain on the taskbar after it is deleted. Delete the taskbar application separately. • 1-5-4 Starting up the PC Application To start up the PC Application, double-click the " Aiphone_JKW " icon on the desktop. You can also start up the PC Application by selecting "Aiphone_JKW" from the "All Programs" lis
Aiphone JKW-IP, 10 11 INTRODUCTION Downloading and setting the Encryption Key 3-4-1 Downloading Encryption Key Person setting up network IP Video Intercom Adaptor Connected directly or via a hub. Network setup PC Administrator PC User PCs Administrator User Perform through below in order to configure the product settings. The product cannot be used unless the settings have been configured. M Admini- strator User Admini- strator User STEP 1 STEP 1 STEP 3 STEP 2 STEP 3 (Up to 9 PCs) 1 2 1 2 1 3 2 3 4 5 6 P.12 P.12 P.17 P.54 P.53 P.12 P.16 P.12 P.1
Aiphone JKW-IP, 30 31 IP Video Intercom Adaptor Settings The downloaded update file is written to the circuit board. Writing takes about 2 minutes. "Firmware update was completed successfully." is displayed, and the update process is complete. MEMO Do not turn off the power while the firmware is being written. If the power is turned off while it is writing, the product will malfunction. • Click [Reboot]. [System is initializing. Please wait. Elapsed Time XX seconds.] is displayed, and the IP Video Intercom Adaptor is rebooted. It takes about 100 seconds to reboot. When the reboot is complete, the Administrator Settings window
Aiphone JKW-IP, 26 27 IP Video Intercom Adaptor Settings Enter the "Connection Port" number, "Audio Port" number, "Video Port" number, and "Web Port" number. The factory default setting numbers are - Connection Port: "5060", Audio Port: "65002", Video Port: "65202", and Web Port: "443". For Global, it may be necessary to change ports when you are using multiple IP Video Intercom Adaptors or PC Applications. Please chec k our homepage at http ://www. aiphone.net for more details. For the broadband router setting information, see the Operation Manual supplied with the broadband router. Click [SAVE]
Aiphone JKW-IP, 2 3 PRECAUTIONS Negligence could result in death or serious injury. 1. Do not dismantle or alter the unit. Fire or electric shock could result. 2. High voltage is present internally. Do not open the case. Electric shock could result. 3. Do not connect any non-specified power source to the +, - terminals. Also, do not install two power supplies in parallel to a single input. Fire or damage to the unit could result. 4. Do not connect any terminal on the unit to an AC power line. Fire or electric shock could result. 5. Do not use power supply with a voltage other than specified. Fire or
Aiphone JKW-IP, 54 55 Example of Registration IP Video Intercom Adaptor HUB / Router LAN ACT AIPHONE JKW-IP STATUS POWER LAN STRIP LENGTH 0.65∼ 1.2 11mm OFF POWER ON DC18V S1 E S2 E S3 E S4 E RY RYB1B2 + - LAN/WAN HUB / Router PC For LAN / WAN ① ② ③ ④ ④ ③ *: The values shown above are the factory default settings. ① Local IP Address and Subnet Mask that were allocated to the IP Video Intercom Adaptor ② Router local IP Address Enter if Email will be sent OFF ① Local IP Address that was allocated to the IP Video Intercom Adaptor Change if necessary. ① Local IP
Aiphone JKW-IP, 28 29 IP Video Intercom Adaptor Settings 3-3-6 Log Downloading / Firmware Update Log Downloading (for Inspections and Maintenance) For maintenance and inspection, you can acquire the operations log from the IP Video Intercom Adaptor. MEMO If you are logged in as a User, you cannot perform a Log Downloading/Firmware Update. The IP Video Intercom Adaptor records the most recent 10 days worth of operations logs. When the recording capacity is exceeded, the logs are overwritten, starting from the log with the oldest recording date. • •
Aiphone JKW-IP, 34 IP Video Intercom Adaptor Settings 35 Setting the Target Email Address and the Email Timing Register the Email Address of the receiver to which a notification is to be sent when a Door Call, Sensor Detection, or System Start is detected. In the Email Timing settings, you can set whether or not Email is transmitted when Door Call, Sensor Detection, or System Start is detected. When Door Call is set to "ON", the snapshot displayed on the monitor at the time of the call is attached to the Email and sent. No Email is sent from the second call. When Sensor Detection is set to "ON", Email is sent when the sensor detection is activated. MEMO To send Emails
Aiphone JKW-IP, 42 PC Application Basic Operations 43 5-1-4 Adjust image If the image displayed on the PC Application screen is difficult to see, you can adjust the image using [ADJUST] ( j ). You can adjust the backlight during the day when a bright background makes it difficult to see. You can make it brighter at night when it is darker. 1 If you click [ADJUST] again while the image is being adjusted, the image is returned to the status from before adjustments were made. Backlight adjustment, Night sensitivity adjustment image <Day> <Night>
Aiphone JKW-IP, Network Settings 16 17 2 Network Settings 2-1 PC Network Settings Provisional registration Registration : Administrator/User Set the IP Address, Subnet Mask, and other necessary information on the PC of the person setting up the network, the Administrator PC, and the User PCs, according to the network environment. From the Windows "start" menu, select "Control Panel" g "Network Connections", then click "Properties" on "Local Area Connection". The "Local Area Connection Properties" wind
50 51 *1 Supported symbols ! # $ % & ’ * + - / ? ^ _ ` { | } ~ ( ) < > [ ] ; @ . *2 Supported symbols ! # $ % & ’ * + - / = ? ^ _ ` { | } ~ ( ) < > [ ] : ; , @ . *3 Supported symbols ! # $ % & ’ * + - / = ? ^ _ ` { | } ~ . Operation Status Comment List A list of comments displayed in the PC Application. Operation Status Comment L
Aiphone MY-CB Security Camera Operation & user’s manual
MY-CB |
Aiphone MA-D Security Camera Operation & user’s manual
MA-D |
Aiphone PB-YKX Security Camera Instructions
PB-YKX |
Aiphone KBW-M Security Camera Instructions
KBW-M |
Aiphone AUDIO DOOR STATION JA-D Security Camera Operation & user’s manual
AUDIO DOOR STATION JA-D |
Aiphone GF-VBC GF-4Z Security Camera Installation manual
GF-VBC GF-4Z |
Aiphone LAF-10B Security Camera Installation manual
LAF-10B |
Aiphone GF-NS Security Camera Operation & user’s manual
GF-NS |
# | Manufacturer | Model | Document Type | File | Updated | Pages | Size |
---|---|---|---|---|---|---|---|
1 | Epson | PowerLite 600p | Brochure | epson/powerlite-600p-843.pdf | 22 Jul 2022 | 6 | 0.56 Mb |
2 | Power Wheels | CAMP BARBIE 74780 | Owner's manual | fisher-price/camp-barbie-74780-XL7.pdf | 06 Apr 2023 | 28 | 1.25 Mb |
3 | Uniden | Bearcat 980 SSB | Owner's manual | uniden/bearcat-980-ssb-J1X.pdf | 15 Dec 2023 | 44 | 3.43 Mb |
4 | Masterbuilt | 20010106 | Assembly, use & care manual | masterbuilt/20010106-ND2.pdf | 14 May 2023 | 6 | |
5 | Brita | Aqualux OB37/OB03 | Operation & user’s manual | brita/aqualux-ob37-ob03-OM4.pdf | 09 Sep 2022 | 2 | 2.17 Mb |
6 | Sony | CMD-J26 | Service manual | sony/cmd-j26-4D2.pdf | 08 Oct 2023 | 20 | 1.95 Mb |
Samsung
www.samsungipolis.comSNV-1080RThe SNV-1080R is a compact vandal-resistant VGA network dome camera featuring built-in IR LEDs which make it suitable for use in the most demanding applications. With the Samsung Techwin WiseNetS DSP chipset at its core, the SNV-1080R delivers a host of advanced features including face detection analytics, third …
SNV-1080R(2 pages) |
Honeywell
Before connecting the cables, take a minute to familiarize yourself with the cables, as Performance Series CamerasPerformance Series IP HDZP304DI 30x Zoom IR PTZ Dome Camera Quick Start Guide Cautions and Warnings CAUTION Installation and servicing should be performed only by qualified and experienced technicians to conform to all local codes and to main …
HDZP304DI(2 pages) |
IMOU
Camera ×1QSG ×1Bracket ×1Power Cable ×1Positioning Map ×1Screw Package ×1Battery ×1 Introduction Note:Press and hold the SYNC button for 8 s to reset the camera. Press the SYNC button to pair with the base station. Power PortSYNC ButtonBuilt-in SpeakerThe pattern of the LED indicator is included in the following table. LED Indicator Status Device St …
LOOC(4 pages) |
Samsung
Before attempting to connect or operate this product,please read these instructions carefully and save this manual for future use. Supreme Resolution WDR Camera WDR-SV4 & SHC-735 User’s ManualENGLISH
…
WDR-SV4(23 pages) |
Eaton
Explosionsgeschützte LED-Rettungszeichenleuchte Serie: Ex-Lite, Ex-Lite V-CG-S, Ex-Lite 24 V, Ex-Lite LTExplosion protected LED exit luminaire Series: Ex-Lite, Ex-Lite V-CG-S, Ex-Lite 24 V, Ex-Lite LTPanneau de signalisation de sortie de secours lumineux antidéflagrant à diodes électroluminescentes Series: Ex-Lite, Ex-Lite V-CG-S, Ex-Lite 24 V, Ex-L …
Crouse-hinds series(8 pages) |
SVAT
CV503-8CH-19M1 SVAT ELECTRONICSnow you can see1 INSTRUCTION MANUALModel#: CV503-8CHwww.SVAT.comwww.SVAT.com8 Channel H.264 Smart LCD-DVR Security Systemw/ Coaching iMenu and Night Vision Surveillance CamerasCOMPLETE SYSTEM
…
CV503-8CH(91 pages) |
Avanti Refrigerator RA751WTRA751WT Instruction manual - AI24U5 RA751WT, 20 |
Morel Speakers Integra Series INTEGRA OVATION 4Integra Series INTEGRA OVATION 4 Install manual - IBK8S9 Integra Series INTEGRA OVATION 4, 2 |
Winic DVR CW-AR304-4Winic CW-AR304-4 DVR Quick operation manual CW-AR304-4, 30 |
Logitech Keyboard K810Keyboard #24XIJC K810, 64 |
GE Microwave Oven JES1290BJ#7Q6P9X: JES1290BJ Microwave Oven Datasheet JES1290BJ, 2 |
Topcom Telephone BUTLER 900Telephone #BXQ162 BUTLER 900, 20 |
Canon Printer iPF500 - imagePROGRAF Color Inkjet PrinterBrochure for Canon iPF500 - imagePROGRAF Color Inkjet Printer Printer iPF500 - imagePROGRAF Color Inkjet Printer, 12 |
IBM Other NETFINITY 4000RIBM Other Manual (File: ibm-netfinity-4000r-manual-102, 25/08/2023) NETFINITY 4000R, 102 |
ZyXEL Communications Gateway LTE7410ZyXEL Communications LTE7410 User Manual (Doc Type: Gateway Quick start manual) LTE7410, 127 |
SoundTube Speakers CM600i#51KCTS CM600i: SoundTube Speakers Owner Documentation CM600i, 4 |
LENCO Portable Speakers Grid-7Portable Speakers Operation & user’s manual (LENCO Grid-7) Grid-7, 10 |
Pioneer Projector PDSP-1Pioneer PDSP-1 Manual (Operating instructions manual), @159MQI PDSP-1, 44 |