Manualios.com

Tinkerine Studio Ditto Assembly Manual

Tinkerine Studio Ditto Manual Online:

4.2, 1560 votes
Tinkerine Studio Ditto User Manual
Tinkerine Studio Ditto User Guide
Tinkerine Studio Ditto Online Manual

Text of Tinkerine Studio Ditto User Guide:

  • Tinkerine Studio Ditto, TINKERINE STUDIO STUDIO [email protected] | 1-604-288-877845 9. You’re almost done with the gantry assembly. For the most part you should now have a gantry system that you can move manually by hand. Move on to part three of the gantry assembly to complete the gantry system. Take extra care when inserting the smooth rod into the linear bearing. Go at it slowly and make sure to not force the rod into the bearing to prevent the ball bearings from dislodging.

  • Tinkerine Studio Ditto, TINKERINE STUDIO STUDIO [email protected] | 1-604-288-877849 5. Your printer’s gantry system should be fully assembled now. You should be able to manually move the carriage around on the X+Y axis. Double check to make sure all belts are properly secures + tensioned, and that all setscrews are properly tightened.

  • TINKERINE STUDIO STUDIO [email protected] | 1-604-288-877844 8. Insert the belt tensioning screws as shown into the four sliders. Refer to the image below to see a closer view. Push down on the belt to create a gap so you can screw in the M3x10 screw over the at surface of the belt. Turn until the screw threads into the far side of the slider panel and the screw head

  • Tinkerine Studio Ditto, TINKERINE STUDIO STUDIO [email protected] | 1-604-288-87783 IMPORTANT SAFETY INSTRUCTIONS ! WARNING SHARP EDGES ! WARNING FIRE ! WARNING SHOCK ! WARNING HOT SURFACE Motor surfaces become hot during operation. There is a danger of electric shock. Use only undamaged electrical chords. DO NOT touch bare wires or receptacles. DO NOT touch the 3D printer or chords if hands are wet. Ensure that all cords are free of damage before connecting to the power supply. Ensure that you have a sufcient electrical supply for

  • TINKERINE STUDIO STUDIO [email protected] | 1-604-288-877847 1. 2. A. Fasten the motor bracket to the motor and slide the pulley onto the motor shaft. Lightly tighten the motor bracket screws as you will need to make minor adjustments in the second step. B. Before inserting the motor bracket into the slot on the frame, insert a M4 nut into the T-s

  • Tinkerine Studio Ditto, TINKERINE STUDIO STUDIO [email protected] | 1-604-288-877872 1. Route the wires from the Left Side LED, X+Y+Z-Axis Endstop, X+Y Motor wire through the wire holes from the front side of the machine to the back. Route the wire so it runs behind the Y-Axis motor and underneath the X-Axis motor. Run all wires through the hole located on the back corner of the motor bracket. 2. Gather all the wires from the carriage fan, heater cartrige, thermister, Right Side LED, and extruder and route the wires through the hole located on the motor bracket. 3. You may choose to label the wires with masking tape before you route them through the hole located on the bot

  • Tinkerine Studio Ditto, TINKERINE STUDIO STUDIO [email protected] | 1-604-288-877867 Print Bed Assembly Tools Required M3 Allen Key Parts Required Print Bed Filament Guide Tube T.I.M LCD/SD Controller Calibration Springs Thumb Nut x3 x3 M3x25 Flathead Screw x3

  • Tinkerine Studio Ditto, TINKERINE STUDIO STUDIO [email protected] | 1-604-288-87786 Ditto+ Bill of Material (30) M3 x 10 screws (85) M3 x 16 screws (12) M3 x 20 screws (8) M3 x 25 screws (11) M3 x 35 screws (3) M3 x 50 screws (3) M3 x 25 athead (1) M4 x 16 screws (3) M4 x 20 screws (10) M3 washers (100) M3 nuts (1) M4 washers (10) M4 nuts (2) Wires (Arduino to Power) (1) M4 Allen Key (1) M3 Allen Key (1) 1.5mm Hex Key (2) Zip Ties Ditto+ Laser Cut Panels (1) Hotend (1) Cartridge heater (1) Thermistor (1) NEMA17 Extruder motor (1) “Tensioning” bearing (1) Cooling fan ducts (1) Filament guiding tube (2) 166mm

  • Tinkerine Studio Ditto, TINKERINE STUDIO STUDIO [email protected] | 1-604-288-877821 Ditto Frame Assembly pt.2 M3 Nuts x12 Tools Required M3 Allen Key Parts Required M3x16 Screw x6 M3x20 Screw x4 M3x25 Screw x2 x2 Z-Axis Smooth Rod (350mm) Lead Screw NEMA17 Stepper Motor Z-Constraint D Assembled Z-Platform Endstop Switch Endstop Spacer x3 x5 M3x10 Screw x4

  • Tinkerine Studio Ditto, TINKERINE STUDIO STUDIO [email protected] | 1-604-288-877840 3. 4. X-Axis Cross Rod (310mm) X-Axis Bearing Y-Axis Bearing Y-Axis Cross Rod (280mm) Take extra care when inserting the smooth rod into the linear bearing. Go at it slowly and make sure to not force the rod into the bearing to prevent the ball bearings from dislodging. A A B C ! Take extra care when inserting the smooth rod into the linear bearing. Go at it slowly and make sure to not force the rod into the bearing to prevent the ball bearings from dislodging. !

  • Tinkerine Studio Ditto, 1. M3x20 (x2) M3x20 (x2) M3x25 (x2) TINKERINE STUDIO STUDIO [email protected] | 1-604-288-877826 Install each endstop triggers as shown. Note the orientation of the trigger and the direction it’s pointing. Depending on the trigger, you will need to different amounts of spacers between the endstop. After the endstop trigger is installed. Thread the wires through the holes shown in the picture. Use one of the smaller adhesive wooden clips provided in your kit to prevent the wire from slacking/getting caught once the printer is in motion. Insert the wire into the clip and tape it t

  • TINKERINE STUDIO STUDIO [email protected] | 1-604-288-877824 3. M3x10 (x4) Lay the printer on its back. Insert the Z-Axis Motor and lead screw from the bottom and into the Z-Axis platform. To connect the the lead screw into the nut within the platform you will need to manually turn the lead screw rod until it threads into the nut. Secure the motor to the frame with four

  • Tinkerine Studio Ditto, TINKERINE STUDIO STUDIO [email protected] | 1-604-288-877874 *Negative ends of the wire that do not have connector pins are marked with a black ink on the ends* *After you have thread the endstop wires through the black plate, attach the pins into the connector housing before you plug them in. Heater Cartridge Extruder Motor X Motor Y Motor Z Motor X Endstop Y Endstop Z Endstop Thermistor Cooling Fans (Hotend + Electronics) Cooling Fans (Print Bed) RAMPS 1.4 LED Strips + + - - Gnd N L Heated Bed NG Power Socket + Switch L Power Supply

  • Tinkerine Studio Ditto, TINKERINE STUDIO STUDIO [email protected] | 1-604-288-877827 1. Insert both ends of the belt onto the Slider B piece. Make sure to line up the belt with the teeth so that there is no spaces left at the end of the slots. Gantry Assembly pt.1 Tools Required M3 Allen Key Parts Required M3x16 Screw x20 8 Pieces Bushing Holder w/ Brass Bushing Slider Side Panels Slider Core GT2 Belt (602mm) GT2 Belt (545mm) x2 x8 x2 Pulley (Large) Outer Bearing Cap Inner Bearing Cap 8 Pieces 8 Pieces GT2 Loop Bel

  • Tinkerine Studio Ditto, TINKERINE STUDIO STUDIO [email protected] | 1-604-288-877873 Extruder Motor X Motor Y Motor Z Motor There is a small triangle on the rightmost side. Make sure it aligns as shown in the diagram. If there is no marking on the housing, face the exposed pin side toward the electronics cooling fan. IMPORTANT !

  • Tinkerine Studio Ditto, TINKERINE STUDIO STUDIO [email protected] | 1-604-288-877851 1. 2. Place the bottom portion of the extruder onto the carriage and insert the hotend + hotend mount into the center of the carriage through the slot located on the back on the carriage. With the two M3x20 screws, secure the extruder and hotend to the top plate of the carriage. The screws should thread into the hotend mount, securing all the components together. Ensure that the acrylic spacer is attached to the top of the hotend and leave the ceramic insulation wrapping attached to the hotend. From the front, your carriage should now look like this. Make sure the larger portion of the extrude

  • Tinkerine Studio Ditto, TINKERINE STUDIO STUDIO [email protected] | 1-604-288-877816 Top Ring Panel FRONT BACK LED Strip (x2) Using the two LED light strip supplied in your kit, one-by-one peel off the backing to reveal the adhesive strip and stick the LED strip in the area shown in the picture. Make sure the LED is applied inbetween the T-Slot and edge of the inner ring. The front and back side of the ring panel will be wider.

  • Tinkerine Studio Ditto, 1. TINKERINE STUDIO STUDIO [email protected] | 1-604-288-877868 One by one, place a spring between the print bed and the wooden platform (beveled hole side up). Insert the athead M3x25 screw from the top and secure it with a thumb nut. Repeat until you have all three points secured. Turn the thumb nut to tension the spring, idealy you will want the spring to be compressed so the bed is rmly planted onto the platform. M3x25 Flathead Screw (x3) M3 Thumb Nut (x3) Calibration Sping (x3)

Related Products and Documents (3D Printers):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 Spectral Audio Neptune Service manual spectral-audio/neptune-33O.pdf 12 Apr 2023 7
2 HTC Touch Diamond 080716 Quick start manual htc/touch-diamond-080716-TBX.pdf 02 Aug 2023 2
3 Karcher KA 1015 Operation & user’s manual karcher/ka-1015-97C.pdf 19 Jan 2024 36
4 Ampetronic ILD500 Handbook ampetronic/ild500-TZD.pdf 03 Jul 2022 13
5 LG KS360 Operation & user’s manual lg/ks360-HUH.pdf 09 May 2023 74
6 Lexmark X83 Service manual lexmark/x83-448.pdf 10 Feb 2023 11

Similar Resources:

  • Felix printers

    Felix 2.0

    (51 pages)
    Assembly instruction manual FELIX 2.0 3d printer [email protected]  www.FELIXprinters.com Page 1 of 51 Version1 – 24-August -2013 Copyright Information This document contains proprietary information that is protected by copyright. No part of this document may be photocopied, reproduced, or translated to another language w …
  • TRAK

    3ntr Series

    (98 pages)
    TRAK® 3ntr 3D Printers Printer and MMS - Installation & Printing Manual Covers Current Models: • 3ntr A2v4 • 3ntr A4v4 • MMS v2 2615 Homestead Place Rancho Dominguez, CA 90220-5610 USA T | 310.608.4422 | F | 310.764.2668 Service Department: 800.367.3165 e-mail: [email protected] | [email protected]
  • Tumaker

    NX PRO DUAL

    (15 pages)
    NX PRO DUALUSER MANUALÍndEXPrinter Specications ................................... 2Main parts of the printer ................................ 3Elements included in the printer .................... 3Installation and set up ................................... 4Quick guide ................................................... 6Calibrate dual height......... …
  • Z Corporation

    Z810

    (152 pages)
    Z810 System User Manual January 2004 Copyright © 2002-2004 Z Corporation Rev. F, Part Number 09505 Z®810 Color 3D Printer User Manual …
  • SainSmart

    Prusa i3

    (13 pages)
    1 Troubleshooting Manual Please be aware of these options as follows : 1. Mainboard is sensitive to static electricity. Please Touch a grounded object to release static electricity before operation. 2. Please ensure the power wire connection is correct. 3. Please Cut off the power when changing interface connection. …
  • Glowforge

    Glowforge

    (39 pages)
    DRAFT Glowforge Manual Version 2.1.4 Introduction We are over-the-moon excited to introduce you to your Glowforge 3D Laser Printer. It’s here. You’re here. This is a big deal. With your Glowforge, you’re going to do incredible things. You’ll build that custom storage solution that you can’t seem to find in stores. You’ll make the best birthday …

Comments, Questions and Opinions: