Toshiba KP-2004 Service Manual

Text of Toshiba KP-2004 User Guide:

• Toshiba KP-2004, Trademarks • iCLASS is a trademark of HID Corporation. • Microsoft, Windows and the brand names and product names of other Microsoft products are trade- marks or registered trademarks of Microsoft Corporation in the U.S. and/or other countries. • Other company names and product names in this manual are the trademarks of their respective companies. © 2007 TOSHIBA TEC CORPORATION All rights reserved Under the copyright laws, this manual cannot be reproduced in any form without prior written permission of TOSHIBA TEC CORPORATION. No patent liability is assumed,

• Toshiba KP-2004, GENERAL PRECAUTIONS REGARDING THE INSTALLA- TION, SERVICE AND MAINTENANCE FOR e-BRIDGE ID GATE (KP-2004) The maintenance should be done by a qualified service technician. 1) When installing the e-BRIDGE ID Gate, follow the procedure described in the co-packed Unpacking Instructions. 2) No person other than specialized service technicians can unpack or install the e-BRIDGE ID Gate. 3) Be sure to unplug the power cable of the equipment before starting the installation, service or main- tenance. 4) Be sure to unplug the power cable of the equip

• © February 2007 TOSHIBA TEC CORPORATION All rights reserved KP-2004 CONTENTS 1 CONTENTS KP-2004 1. GENERAL DESCRIPTION............................................................................................ 1-1 2. INSTALLATION AND SETTINGS OF e-BRIDGE ID GATE......................................... 2-1 2.1 Setup Procedure...............................................................

• Toshiba KP-2004, © February 2007 TOSHIBA TEC CORPORATION All rights reserved KP-2004 GENERAL DESCRIPTION 1 - 1 1 1. GENERAL DESCRIPTION e-BRIDGE ID Gate (KP-2004) is a card reader which enables user authentication on a iCLASS-compli- ant noncontact card. * iCLASS is a noncontact IC card technology developed by HID Corporation.

• Toshiba KP-2004, © February 2007 TOSHIBA TEC CORPORATION All rights reserved KP-2004 INSTALLATION AND SETTINGS OF e-BRIDGE ID GATE 2 - 1 2 2. INSTALLATION AND SETTINGS OF e-BRIDGE ID GATE Follow the procedure below to set up the e-BRIDGE ID Gate. Its settings require users to enter their confidential information. Service technicians in the field can only display the entry screen and must have the users enter their confidential information. The table below shows the persons related to the settings and what they do for the settings. Note: Note: Each procedure shown in this chapter has an instruction to turn the power of the eq

• Toshiba KP-2004, KP-2004 © February 2007 TOSHIBA TEC CORPORATION All rights reserved INSTALLATION AND SETTINGS OF e-BRIDGE ID GATE 2 - 2 Setup Flow The setup flow is shown below. For the details of each procedure, refer to the page shown. [A] LDAP server confirmation  P. 2-3 "[A] LDAP server confirmation" Worker Service technician Operation Confirms the user if the attribute name used for card authentication (authentication ID) on the LDAP server is correct. The confirmed attribute name should be set on this equi

• Toshiba KP-2004, © February 2007 TOSHIBA TEC CORPORATION All rights reserved KP-2004 INSTALLATION AND SETTINGS OF e-BRIDGE ID GATE 2 - 3 2 2.1 Setup Procedure [A] LDAP server confirmation The service technician confirms a user if the attribute name used for card authentication (authentication ID) on LDAP server is correct. The confirmed attribute name should be set on this equipment in proce- dure [K]. [B] Authentication method confirmation The user accesses TopAccess and confirms if “Enable” of “Department Code” and “User Authentica- tion” is selected. The user also confirms if either of “Windows Domain Authentication” or “LDAP Authen- tication” of “Authentication” is sele

• Toshiba KP-2004, KP-2004 © February 2007 TOSHIBA TEC CORPORATION All rights reserved INSTALLATION AND SETTINGS OF e-BRIDGE ID GATE 2 - 4 [E] LDAP server setting (08-1927) The service technician sets the attribute name of the LDAP server authentication ID which has been confirmed in procedure [A] on the equipment. Check the attribute name confirmed in procedure [A]. <Procedure> 1) Turn the power of the equipment ON while pressing the digital keys [0] and [8] simultaneously. 2) Key in “1927”, and then press

• Toshiba KP-2004, © February 2007 TOSHIBA TEC CORPORATION All rights reserved KP-2004 e-BRIDGE ID GATE SETTING CODE LIST 3 - 1 3 3. e-BRIDGE ID GATE SETTING CODE LIST Code Items/Contents 08-1772 Card reading device setting <Acceptable value: 8 digits> To enable the e-BRIDGE ID Gate, a card reading device should be set in the order of "ABYYZZZZ". (Enter the corresponding values to "A", "B", "YY" and "ZZZZ".) • AB:Special setting • A: Debugging NIC 0: Not used 1: Used •B:Interface 0: USB connection 1: N/A • YY:Authentication 00:

• Toshiba KP-2004, © February 2007 TOSHIBA TEC CORPORATION All rights reserved KP-2004 TROUBLESHOOTING 4 - 1 4 4. TROUBLESHOOTING 1) The e-BRIDGE ID Gate does not beep when an IC card is brought close to it, or the screen of the equipment is not switched. The equipment does not recover from the energy save mode even if an IC card is brought close to the e-BRIDGE ID Gate. Check the following: - Is the IC card close enough to the e-BRIDGE ID Gate? If the IC card and the e-BRIDGE ID Gate are separated 3 cm or more, the

• KP-2004 © February 2007 TOSHIBA TEC CORPORATION All rights reserved TROUBLESHOOTING 4 - 2 3) The e-BRIDGE ID Gate beeps three times consecutively (one short beep, a short period and then a set of short and long beeps) and a message “Failed Authentication” appears on the equipment’s touch panel. Check the following: - Is the IC card authentication server is the LD

• Toshiba KP-2004, © February 2007 TOSHIBA TEC CORPORATION All rights reserved KP-2004 CANCELING e-BRIDGE ID GATE CARD AUTHENTICATION 5 - 1 5 5. CANCELING e-BRIDGE ID GATE CARD AUTHENTICATION Canceling the card authentication with the e-BRIDGE ID Gate Perform the following setting: Key in “00000000” on the code 08-1772. For the procedure, refer to “[D] System setting (08-1772)”.  P. 2-3 "[D] System setting (08-1772)" 08-1772 When canceling the card authentication with the e-BRIDGE ID Gate Setting code (8 digits): 00000000

Related Products and Documents (Card Reader):

Comparable Devices:

Similar Resources:

• Linkskey LKA-CR15BW (20 pages) USB2.0 ICSI Card reader Manual1I n d e x1. Product Features 022. Manual for Windows2.1. Installment under win 98SE 032.2. Annotation 062.3. Check if the installment of driver under win98 SE 072.4. Check if the installment of driver under win ME/2000/XP 092.5. Two Kinds of methods for Un-installment under win 98SE 103. Installment Under the MAC 9.X /10.2.8 ab …

• Vicon VAX-D6.4R (2 pages) This Quick Start Guide is intended for experienced installing technicians. It is a basic reference to ensure all connections are properly made. It is for model VAX-D6.4R-OSDP. For additional information please refer to Vicon's website vicon-security.com.1.0 IntroductionA key component of a physical security electronic access control system, a contactle …

• Tecnoalarm APR FINGER-CARD (34 pages) Apr Finger-Card - Ver. 1.0 - 09/2011Ver. 1.0 - 09/2011 - Apr Finger-Card 1APR FINGER-CARDDispositivo di comando con lettore biometrico di improntedigitali e carte RFIDUnité de contrôle avec lecteur biométrique d'empreintesdigitales et de cartes RFIDControl unit with biometric finger print and RFID card readerUnidad de control con lector biométrico d …

• Gallagher HR3 (126 pages) ! "#$%!&'()'*! +! ,-.&'()$*!/$!*0)12*2#'1$)%!! +! 345! 6$()17$%8'(/9):8! +! ;,"! &'()'*!/$*!"#)'%2<! +! ,=>! &'()'*$!"1$(1$! +! ?@5Smart4$'/$%!A4B"#$%!&'()'* …

• Salto XS4 (4 pages) Installation Guide XS4 Glass Door Lockwwww.saltosystems.com Installation guide XS4 Glass Door LockThe XS4 glass door lock is stylish and modern. It’s exclusive design makes it com-patible with a wide range of glass door designs, including those already tted with built-in lock. It’s ‘sandwich body’ design also makes for easy install …

• Datamars R-IN1300 MID (41 pages) R-IN1300 MIDHF – multi readTEXTILE IDUSER MANUALVersion 3.0Corporate Headquarters - Textile ID business division:Via Industria 166814 LamoneSwitzerlandPhone: +41 91 935 73 80 Fax: +41 91 945 03 [email protected] www.textile.datamars.com …

Comments, Questions and Opinions: