Manualios.com

Toshiba DB-EA4D Owner's Manual

Toshiba DB-EA4D Manual Online:

4.3, 2307 votes
Toshiba DB-EA4D User Manual
Toshiba DB-EA4D User Guide
Toshiba DB-EA4D Online Manual

Text of Toshiba DB-EA4D User Guide:

  • Toshiba DB-EA4D, Résumé des précautions FRENCH VERSION iv Assurez-vous que votre installation est correctement reliée à la terre. Une mauvaise installation peut provoquer un début d’incendie ou un choc électrique. Ne pas retirer les capots, réparer ou modifier l’imprimante par vous- même. Vous pouvez recevoir un choc électrique ou vous blessé par des bords tranchants dans l’imprimante. Ne pas utiliser de spray nettoyant contenant du gaz inflammable pour nettoyer ce produit, ceci pourr

  • Toshiba DB-EA4D, 5. PRINTER SETUP ENGLISH VERSION 5.9 Parameter Setting In Menu Mode E5-33 The following settings of Menu Mode are valid in H print test. Paper Type, Form Length, Paper Width, Paper Density, Power Control, Maximum Speed, Page Recovery (only Online mode), BM Cut Offset, Label Cut Offset, Top Margin, Label Top Margin, BM Cut Position and Label Cut Pos, Paper Load. 3. Dot check pattern print test This mode performs rolling Dot check pattern print test repeat, and page number is printed on the top left corner of the page. The print result as follows. If the setting of

  • 3. APPEARANCE ENGLISH VERSION 3.1 Dimensions E3-1 3. APPEARANCE 3.1 DIMENSIONS All dimension in mm 3.2 FRONT VIEW 3.3 REAR VIEW Power Switch O: OFF I: ON AC Power Inlet USB Interface LAN Interface Parallel Interface (Centronics)

  • Toshiba DB-EA4D, 6 Waste Recycling information for users: Following information is only for EU-member states: The use of the crossed-out wheeled bin symbol indicates that this product may not be treated as general household waste. By ensuring this product is disposed of correctly you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. For more detailed information about the take-back and recycling o

  • Toshiba DB-EA4D, 5. PRINTER SETUP ENGLISH VERSION 5.7 Sensor Calibration E5-13 5.7.1 SENSOR CALIBRATION WITH BLACK MARK This mode performs Sensor level adjustment test with Black Mark paper. Sequence: 1. Select “Sensor Calibration” in main menu of Menu Mode, And Press [FEED] key shortly. A message appears on the LCD, as shown below. 2. Press [FEED] key shortly. A message appears on the LCD, as shown below. 3. Remove paper and roll paper. 4. Press [FEED] Key shortly. A message appears shortly on the LCD, as shown bel

  • Toshiba DB-EA4D, 8. TROUBLESHOOTING ENGLISH VERSION 8.2 Possible Problems E8-3 8.2 POSSIBLE PROBLEMS Problem Causes Solutions The printer will not turn on. 1. The Power Cord is disconnected 1. Plug in the Power Cord. 2. The AC outlet is not functioning 2. Test with a power cord from another electric appliance. 3. The fuse has blown or the circuit breaker has tripped. 3. Check the fuse or breaker. The media is not fed. 1. The media is not loaded properly. 1. Load the media properly. 2. The printer is in an error condition. 2. Solve the error in the message display. The printed image is blurred. 1. Th

  • 7. GENERAL MAINTENANCE ENGLISH VERSION 7.1. Cleaning E7-1 7. GENERAL MAINTENANCE 7.1 CLEANING CAUTION: 1. Do not use any sharp objects to clean the print head and platen. Doing so may damage them, causing poor print quality or miss

  • Toshiba DB-EA4D, 5. PRINTER SETUP ENGLISH VERSION 5.8 Printer Driver Installation E5-18 4.Select “Local printer” and “Automatically detect and install my Plug and Play printer”, Click “ Next”. 5. PC will detect new hardware and open “Hardware Wizard” 6.When the New Hardware Wizard ask whether to connect to Windows Update, Select “ No, not this time” and click “Next”. 7.Select “Install from a list of specific location(Advanced)” and click “Next”.

  • Toshiba DB-EA4D, 8. TROUBLESHOOTING ENGLISH VERSION 8.2 Possible Problems E8-3 8.1 ERROR MESSAGES (Cont.) Error Messages LED Problems/Causes Recovery Online Error ERROR EEPROM On On EEPROM access is not available. Turn the printer off and then on. If does not solve the problem, Call a TOSHIBA TEC authorized service representative READY NONE CG Blink slowly Off During printer Power ON, the value of Check code in CG Data and ROM are different. (It is possible to print on Online Mode without CG) Downloaded the correct CG Data by IPL. READY COOLING DOWN Blink slowly Off Thermal h

  • 8. TROUBLESHOOTING ENGLISH VERSION 8.2 Possible Problems E8-2 8. TROUBLESHOOTING 8.1 ERROR MESSAGES Error Messages LED Problems/Causes Recovery Online Error ERROR PAPER EMPTY On Blink slowly No paper is detected Load paper ERROR COVER OPEN On Blink slowly The therm

  • Toshiba DB-EA4D, 4. BASIC FUNCTIONS OF OPERATION PANEL ENGLISH VERSION 4.2 Keys On The Normal Mode E4-1 4. BASIC FUNCTIONS OF OPERATION PANEL 4.1 LED INDICATION 4.1.1 POWER (ONLINE) LED 1. Indicate power on state. 2. Light when the printer power is on. 3. Blink slowly when the printer detects warnings. 4. Blink fast when the printer is in IPL mode. 4.1.2 ERROR LED 1. Indicate error state. 2. Light when the printer detects fatal error. 3. Blink slowly when the printer detects no paper

  • Toshiba DB-EA4D, 4. BASIC FUNCTIONS OF OPERATION PANEL ENGLISH VERSION 4.3 Special Functions E4-7 4.3.3 Menu Mode Sequence: 1. There are two different ways to enter Menu Mode. a) When the printer is powered off, press and hold [MENU] key and turn the printer on. b) When the printer is on and in READY or PAUSE state, press and hold [MENU] Key for three seconds. 2. All I/F are in BUSY state during this mode. And a message appears on the LCD, as shown below. 3. During the above message is displayed, a) Press [FEED] Key shortly, it enters the Menu Mode. b)

  • Toshiba DB-EA4D, 2. SPECIFICATIONS ENGLISH VERSION 2.2 Media Specifications E2-6 2.2.4 Effective Print Area of Paper The figure below illustrates the relation between the head effective print width and media width. 2.3 OPTIONS Option Name Type Description Rotary Cutter DB-EA204-RC-QM-R A rotary cutter used to repeatedly cut media Paper Roll Holder DB-EA904-PH-QM-R A media roll hanger for media roll with an outer roll diameter up to 203.2mm (8”) and

  • Toshiba DB-EA4D, 2. SPECIFICATIONS ENGLISH VERSION 2.1 Printers Specifications E2-1 2. SPECIFICATIONS 2.1 Printers Specifications Item Supply voltage AC 100 – 120V, 50/60 Hz ± 10%; AC 220 – 240V, 50 Hz ± 10% Power consumption 100V – 240V 3.3A – 1.4A (Dual side, Print Ratio 14% Duty Slant Pattern, 6 inc/sec.) Operating temperature 0 - 40°C (In case 0°C-5°C: Max Speed: 4 inch/sec.) Relative humidity 25 - 85% (No condensation) Print head Line thermal 8 dots per mm (203.2 dots per inch) Printing methods Line thermal printing (Direct thermal method) Print speeds Max 6 inch/sec. (Dual side printing mode) Maximum prin

  • Toshiba DB-EA4D, 5. PRINTER SETUP ENGLISH VERSION 5.9 Parameter Setting In Menu Mode E5-25 5.9 PARAMETER SETTING IN MENU MODE 5.9.1 CATEGORY “FIRMWARE VERSION, CRC” This category indicates Version Nnumber and CRC of Firmware. Not changeable in this category. Function Description Main Firmware Display the version number and CRC of the installed main firmware on the second line of the LCD as below. vvvvv: 5 digits for the version number cccc: 4

  • Toshiba DB-EA4D, APPENDIX I INTERFACE ENGLISH VERSION APPENDIX I INTERFACE A-2 Parallel Interface (Centronics) Mode: Conforming to IEEE1284 Compatible mode (SPP mode), Nibble mode Data input method: 8 bit parallel Pin No. Signal In/Out Pin No. Parallel In/Out 1 nSTORBE In 19 Signal GND 2 DATA0 In 20 Signal GND 3 DATA1 In 21 Signal GND 4 DATA2 In 22 Signal GND 5 DATA3 In 23 Signal GND 6 DATA4 In 24 Signal GND 7 DATA5 In 25 Signal GND 8 DATA6 In 26 Signal GND 9 DATA7 In 27 Signal GND 10 nACK Out 28 Signal GND

  • Toshiba DB-EA4D, 5. PRINTER SETUP ENGLISH VERSION 5.7 Sensor Calibration E5-12 5.7 SENSOR CALIBRATION It is necessary to perform sensor calibration prior to paper loading if using an non-specified paper by TOSHIBA TEC, by following the below procedure: 2ST printer supports 4 categories of sensor calibration functions. Refer to the following table. Function Description Calibration with BM Paper It performs sensor calibration with black mark paper. Calibration with White Paper It perfor

  • Toshiba DB-EA4D, 4. BASIC FUNCTIONS OF OPERATION PANEL ENGLISH VERSION 4.3 Special Functions E4-8 Key Function 1. Press [FEED] Key shortly, it shifts the selection mode as shown below. 2. Press [FEED] Key shortly, it shifts the selection mode when a message appears on the LCD, as shown below. 3. Press [MENU] Key shortly, it shifts to the next selection mode in order, as shown below. Firmware Version, CRC Communication Interface Printer Configuration Printer Adjustment Printer Test Modes Sensor Calibration Menu Exit Function selection mode Main Firmware Boot Firmware SBCS CG Return to Prev. Layer Menu settin

  • APPENDIX I INTERFACE ENGLISH VERSION APPENDIX II MENU MODE TREE A-8 APPENDIX II MENU MODE TREE (Cont.) Main menu Function Menu setting Acknowledge Result Printer Adjustment BM Cut Position xxx BM Cut Position -15 -15 Accepted BM Cut Position xxx xxx Accepted

  • Toshiba DB-EA4D, 8 5.3 SETTING THE SENSOR POSITION ........................................................................................................................................... 5 5.3.1 SETTING THE BLACK MARK SENSOR POSITION ................................................................................................... 5 5.3.2 SETTING THE LABEL GAP SENSOR POSITION ....................................................................................................... 6 5.4 MENU MODE ...............................................................................................................................................................

  • Résumé des précautions FRENCH VERSION iii Résumé des précautions La sécurité personnelle lors de la manipulation ou de l’entretien du matériel est extrêmement importante. Les avertissements et précautions nécessaires à la manipulation en toute sécurité du matériel sont inclus dans ce manuel. Les avertissements et précautions con

  • Toshiba DB-EA4D, 5. PRINTER SETUP ENGLISH VERSION 5.6 Paper Type Setting E5-11 5.6 PAPER TYPE SETTING If use “BM Paper”, “White Paper” ,“Perforation Paper” or “Cut Sheet Paper”, Perform below sequence. (Default Setting: Label) Sequence: 1. Select “Printer Configuration” in main menu of Menu Mode. And press [FEED] key shortly. A message appears on the LCD, as shown below. 2. Press [FEED] key shortly. A message appears on the LCD, as shown below. 3. Select “Black Mark”, “Document Length”, “Perforation” or “Cut Sheet”.

More Instructions:

DOWNLOAD
DOWNLOAD

Related Products and Documents (Label Maker):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 Bush Hog TH420 Operator's manual bush-hog/th420-9C6.pdf 24 Jul 2022 82 6.87 Mb
2 Renault Laguna Manual  renault/laguna-LD5.pdf 22 Jun 2022 23 1.68 Mb
3 Canon PowerShot G1 Parts catalog canon/powershot-g1-949.pdf 19 Jun 2022 23 3.82 Mb
4 RedMax PSZ2401 Owner's manual redmax/psz2401-S3U.pdf 01 Jan 2023 68 1.43 Mb
5 Nortel Norstar System administration manual nortel/norstar-4R4.pdf 05 Mar 2023 341
6 Epson PowerLite Pro G5450WU Operation manual epson/powerlite-pro-g5450wu-16Q.pdf 26 Jan 2023 20 0.75 Mb

Similar Resources:

  • Epson

    TM-T88V-i

    (2 pages)
    ENDepending on the model, accessories other than those described above may be included. See Technical Reference Guide.FRSelon le modèle, des accessoires différents des accessoires décrits ci-dessus peuvent être inclus. Voir le Technical Reference Guide (Guide de reference technique).DEJe nach Modell kann anders als das oben beschriebene Zubehör enthalte …
  • Brother

    PT-3600

    (204 pages)
    • Read this User’s Guide before you start using your P-touch.• Keep this User’s Guide in a handy place for future reference.• Antes de usar su equipo por primera vez, lea cuidadosamente esta guía de usuario.• Guarde esta guía de usuario para futuras referencias.USER’S GUIDEGUÍA DE USUARIOUSER’S GUIDEGUÍA DE USUARIOUSER’S GUIDEGUÍA DE U …
  • Intermec

    PB22

    (2 pages)
    Quick Start GuideMobile Printer移动打印机快速入门指南行動印表機快速入門指南Guide de démarrage rapide pour l’imprimante mobileKurzanleitung für MobildruckerPanduan Cepat Printer Bergerak프린터 빠른 시작 안내서Manual de Consulta Rápida do Impressora móvelКраткое руководство по эксплуатации …
  • Labelmate

    PM-300-CS

    (88 pages)
    watch the video PRINTING MECHANISMUSER MANUALPM-300-CSPM-300-CS-STEPTHE WORLD’S LEADING MANUFACTURER OF LABEL DISPENSERS, REWINDERS, UNWINDERS, SLITTERS & COUNTING SOLUTIONS …
  • Brother

    QL-1060N

    (42 pages)
    NETWORK USER’S GUIDEMulti-Protocol On-board Ethernet Print ServerQL-580N / 1060NRead this guide thoroughly before using the machine. Keep the CD-ROM in a convenient place so you can use it quickly if you need to.Visit us at http://solutions.brother.com where you can get product support, the latest driver updates and utilities, and answers to frequently ask …
  • Avery Dennison

    AP5.4 Gen II

    (103 pages)
    03/10 Rev. 5.05-00 USER- / SERVICE MANUALAP 5.4 Gen II – AP 5.6Info Printouts & ParametersGeneral Information ...................................... 5Important setting instructions .................... 5Area of application .................................... 5Operating the parameter menu ..................... 7Example .............................. …

Comments, Questions and Opinions: