BeiJer DT150 Installation Manual

Text of BeiJer DT150 User Guide:

• BeiJer DT150, Foreword Beijer Electronics, MAEN844C DT150 Installation Manual Foreword The DT150 industrial monitor is a TFT-LCD touch screen monitor, designed to be mounted in a cabinet and connected to an industrial PC. The monitor is optimized for a maximum resolution of 1024 x 768 pixels when the full display area of the module is used. This manual explains how to install the monitor. Please see www.hmi.beijerelectronics.com for further information. © Beijer Electronics AB, MAEN844C, 2009-01 The information in this document is subj

• Contents Beijer Electronics, MAEN844C Contents 1 Safety Precautions................................................................................... 5 1.1 General ........................................................................................5 1.2 During Use ..................................................................................6 1.3 Service and Main

• Safety Precautions Beijer Electronics, MAEN844C 5 1 Safety Precautions Both the installer, owner, and operator of the monitor must read and understand this installation manual. 1.1 General – Only qualified personnel may install or operate the monitor. – The monitor must be installed according to the installation instructions. – The monitor is designed

• BeiJer DT150, Safety Precautions 6 Beijer Electronics, MAEN844C 1.2 During Use – Keep the monitor clean. – Emergency stop and other critical safety functions may never be controlled from the monitor. – Do not use force or sharp objects on the display surface. 1.3 Service and Maintenance – Only qualified personnel should carry out repairs. – The agreed warranty applies. – Before carrying out any cleaning or maintenance operations, disconnect the equipment from the electrical supply. – Clean the display and surrounding front cover with a

• BeiJer DT150, Installation Beijer Electronics, MAEN844C 7 2Installation 2.1 Space Requirements Installation plate thickness: 1.5 - 9.0 mm (0.06 - 0.35 inch) Space requirements when installing DT150: 2.2 Installation Process 1. Unpack and check the delivery. If anything is damaged, notify the supplier. Caution: The openings on the enclosure are for air convection. Do not cover these openings. Note: Place the monitor on a stable surface during installation. Dropping it or letting it fall may cause damage. 25 mm 45 mm 50 mm 304 mm 398 mm 50 mm (2.0 in

• BeiJer DT150, Installation 8 Beijer Electronics, MAEN844C 2. Place the panel cut out where the monitor is to be situated, draw along the outer sides of the holes and cut according to the markings. 3. Secure the monitor in position, using all the fastening holes and the pro- vided brackets and screws: x14 0.5 - 1.0 Nm

• BeiJer DT150, Installation Beijer Electronics, MAEN844C 9 4. Connect the cables in the specified order. 5. Carefully remove the laminated film over the monitor display, to avoid static electricity that could damage the monitor. Caution Use only shielded signal cables. Separate high voltage cables from signal and supply cables. Caution: The monitor must be brought to ambient temperature before it is started up. If condensation forms, ensure that the monitor is dry be- fore connecting it to the power outlet. A B Monitor 115/230 V AC Industrial PC 12 V DC VGA/DVI AC/DC Adaptor Ground connected power cord A B - +

• BeiJer DT150, Te ch n i c a l D a t a Beijer Electronics, MAEN844C 11 3 Technical Data Parameter DT150 Front panel, W x H x D 398 x 304 x 6 mm Mounting depth 50 mm Front panel seal IP 66 Rear panel seal IP 20 Front panel material Touch screen: Polyester on glass *, 1 million finger touch operations. Overlay: Autotex F157 or F207. Powder-coated aluminum. Reverse side material Powder-coated alu-zink. Touch interface 3M: SC401U, via USB. Drivers are available at www.3m.com or at www.hmi.beijerelectronics.com Screen setup Via rear membrane keyboard. Video interface VGA and DVI. Weight 4 kg Rated voltage 12 V DC ± 5% Power consu

• BeiJer DT150, Technical Data 12 Beijer Electronics, MAEN844C 3.1 The On Screen Display Menu The On Screen Display (OSD) menu makes it easy to adjust monitor settings. The buttons for accessing the OSD menu are located on the rear side of the monitor. Some of the OSD buttons have multiple functions (a hot key option), listed below. Usually, the display is configured by the automatic display configuration when pressing the Down Arrow button. If advanced configuration is needed, the Menu button displays other options. The - and + buttons are used for navigation, and the Menu button is used to select. The OSD buttons and their function are described below: Button Function Alternat

• BeiJer DT150, Te ch n i c a l D a t a Beijer Electronics, MAEN844C 13 3.1.1 On Screen Menu Descriptions This section describes the accessible sub menus and their functions. Main Menu Sub Menu Function Input Source A RGB Change input signal source to Analog RGB DVI Change input signal source to DVI Exit Go back to main menu Main Menu Sub Menu Function Picture Brightness Adjust brightness of the screen Contrast Adjust distinction (ratio of luminance between black and white) Blacklevel Adjust black level Sharpness Adjust sharpness of pictures Exit Go back to main menu Main Menu Sub Menu Function Color Temperature User: Red, green and blue colors can be adjusted W

• BeiJer DT150, Technical Data 14 Beijer Electronics, MAEN844C Main Menu Sub Menu Function Image Control Avaliable mode: Analog RGB Auto Auto configuration of geometry. Width Adjust horizontal size of the screen by increasing or decreasing the number of picture elements Phase Adjust phase of screen, used when noise or over- lapped lines are shown on the screen H Position Move screen horizontally V Position Move screen vertically Exit Go back to main menu Main Menu Sub Menu Function Tool OSD Control Time Out: Set the duration time of the OSD menu (OSD turn-off time) H Position: Adjust horizontal position of OSD Menu by value V Position: Adjust vertical positio

• BeiJer DT150, Te ch n i c a l D a t a Beijer Electronics, MAEN844C 15 3.2 Operation Messages The following operation messages will be displayed under different circumstances: 3.3 Video Input Timing The following vertical refresh rate is recommended: 3.4 Audio Support The industrial monitor has a built in stereo amplifier that can be controlled ei- ther via the OSD interface or the OSD buttons on the rear side. The monitor is equipped with one audio input port and one speaker out port. Operation message Explanation AUTO TRACKING Auto Tracking (analog RGB mode): Executes auto function NO SIGNAL Self diagnostics (analog RGB mode): No input signal after power-on with power switch. The message w

• Technical Data 16 Beijer Electronics, MAEN844C 3.5 Calibrate the Touch Screen The industrial monitor has a built in touch screen. This is not operational when shipped from the supplier and must be installed. Instructions and drivers for in- stallation of the touch screen function are available at: www.hmi.beijerelectronics.com

• BeiJer DT150, Chemical Resistance Beijer Electronics, MAEN844C 17 4 Chemical Resistance 4.1 Metal Casing The frame and casing material is powder-coated aluminum. This powder paint withstands exposure to the following chemicals without visible change: The powder paint shows limited resitance to the following chemicals at room temperature: The powder paint shows little or no resistance to the following chemicals at room temperature: Acetic acid 10% Phosphoric acid 4% Citric acid 10% Phosphoric acid 10% Diesel Sea water Distilled water Sodium chloride 2% Edible oil Sodium chloride 20% Fuel oil Sulphuric acid 20% Hydrogen peroxide 3% Tap water Butanol Nitric acid 3% Hydrochloric acid 5% Nitric acid 10% I

• BeiJer DT150, Chemical Resistance 18 Beijer Electronics, MAEN844C 4.2 Touch Screen and Overlay 4.2.1 Autotex F157/F207 Autotex F157 or F207 covers the overlay surrounding the touch screen. Solvent Resistance Autotex F157/F207 withstands exposure of more than 24 hours duration under DIN 42 115 Part 2 to the following chemicals without visible change: Autotex withstands DIN 42 115 Part 2 exposure of up to 1 hour duration to gla- cial acetic acid without visible change. Autotex is not resistant to high pressure steam at over 1

• BeiJer DT150, Chemical Resistance Beijer Electronics, MAEN844C 19 4.2.2 Touch Screen Surface The touch screen surface on the monitor withstands exposure to the following solvents without visible change: 4.2.3 Autoflex EB It is recommended to use the Autoflex EB touch display protection film, that can be ordered from Beijer Electronics. Solvent Resistance Autoflex EB withstands exposure to the same chemicals as Autotex F157 or F207 according to section Autotex F157/F207. Outdoor Use In common with all polyester based films Autoflex EB is not suitable for use in con

• BeiJer DT150, HEAD OFFICE SWEDEN Beijer Electronics Products AB Box 426 SE-201 24 Malmö, Sweden Tel: +46 40 35 86 00 Fax: +46 40 93 23 01 [email protected] SUBSIDIARIES GERMANY Elektronik-Systeme Lauer GmbH & Co. KG Kelterstraße 59 72669 Unterensingen, GERMANY Tel: +49 7022 9660 0 Fax: +49 7022 9660 103 [email protected] USA Beijer Electronics Inc. 939 N. Plum Grove Road, Suite F Schaumburg, IL 601 73, USA Tel: +1 847 619 6068 Fax: +1 847 619 6674 [email protected] TAIWAN Hitech Electronics

More Instructions:

BeiJer DT150 Installation manual 16-10-2022 24

DOWNLOAD

Related Products and Documents (Headphone):

Comparable Devices:

Similar Resources:

• Sony ICD-UX523 (2 pages) ICD Common Flyer for PC connectionGB/ES 4-418-154-11(1)4-418-154-11(1)© 2011 Sony Corporation Printed in ChinaCopying Files from the IC Recorder to Your ComputerYou can copy the les and folders from the IC recorder to your computer to store them.1 Connect the IC recorder to your computer.2 Make sure the IC recorder has been recognized properly.On the …

• Sennheiser SET 900 (52 pages) MZA 900 P BedienungsanleitungInstructions for useNotice d‘emploiIstruzioni per l‘usoInstrucciones para el usoGebruiksaanwijzingMZA.book Seite 1 Freitag, 29. April 2005 12:45 12 …

• Lyx Pro LYXOEH10 (2 pages) OPEN AIR HI-FI HEADPHONESUser GuideLY XOEH10Thank you for purchasing the LyxPro OEH-10 Open Air Hi-Fi Headphones. The LyxPro OEH-10 Open Air Hi-Fi Headphones bring outstanding sound quality to the discerning music listener. Experience the high fidelity sounds of your favorite music on the go, essentially bringing the quality of a live performance along with …

• Sennheiser CC 520 IP (2 pages) Quality performanceCC 520 IP Protecting your hearing  HD voice clarity The CC 520 IP wideband headset delivers natural high-definition sound for superior voice clarity, accented speaker recognition, and reduced echo   ed headband  0° adjustable microphone boom for ®  Extra comfort Generous headband padding and extra large ear pads ev …

• Philips SHN050 (2 pages) For preview purpose onlyActive Noise ReductionNeckband noise reduction headphoneA lightweight neckband noise-reduction headphone that is ideal for the bus, train or airplane.Optimal listening in noisy environments• 3.5 - 6.35mm adaptor connects to all types of audio devices• Battery included so you can use your product straight away• Small control box …

• Philips HC8430 (2 pages) Lightweight comfortWirelessJust imagine, no hassles with cables and the freedom to move around and enjoy your music with quality FM wireless stereo headphones.You'll forget you're wearing them!• 3-way adjustment for a better fit and bass performance• Lightweight design improves comfort for prolonged use.The perfect wireless listening experience …

Comments, Questions and Opinions: