Manualios.com

Advantech UR5i v2 Libratum Operation & User’s Manual

  • UR5i v2 Libratum Network Router
  • mawpH/F/aP98Y
  • Operation & User’s Manual
  • PDF / Adobe Acrobat Reader
  • 33

Advantech UR5i v2 Libratum Manual Online:

3.05, 2052 votes
Advantech UR5i v2 Libratum User Manual
Advantech UR5i v2 Libratum User Guide
Advantech UR5i v2 Libratum Online Manual

Text of Advantech UR5i v2 Libratum User Guide:

  • Advantech UR5i v2 Libratum, LIST OF FIGURES List of Figures 1 Contents of package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 2 Front panel UR5i v2L . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 3 Front panel UR5i v2L with WiFi . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 4 Front panel UR5i v2L SL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 5 Front panel UR5i v2L SL with WiFi . . . . . . . . . . . . . . . . . . . . . . . . . 6 6 Example of the router label . . . . . . . . . . . . . . . . . . .

  • Advantech UR5i v2 Libratum, 8. RECOMMENDED LITERATURE 8. Recommended Literature [1] Advantech B+B SmartWorx: Start guide for v2 routers, [2] Advantech B+B SmartWorx: Configuration manual for v2 routers, [3] Advantech B+B SmartWorx: Application note – Programmer guide. 25

  • Advantech UR5i v2 Libratum, 5. ROUTER DESIGN 5.7.2 Power connector PWR Panel socket 2-pin. Pin number Signal mark Description 1 VCC(+) Positive pole of DC supply voltage (+9 to +36 V DC) 2 GND(-) Negative pole of DC supply voltage Table 5: Connection of power connector Figure 18: Power connector Power supply for router is required between +9 V to +36 V DC supply. Protection against reversed polarity without signaling is built into the router. The power consumption during receiving is 2.3 W. The peak power consumption during data sending is 5.5 W. However, values of consumption can be increased, if some expansion port is eqquipped. For correct operation it is necessary t

  • Advantech UR5i v2 Libratum, 5. ROUTER DESIGN 5. Router Design 5.1 Router versions UR5i v2 Libratum router is supplied in the following versions (see table below). All versions are available in plastic or metal box according to customer requirements. Router versions Router Box SIM1 SIM2 ETH0 ETH1 UR5i v2 Libratum Plastic 1 x 1 x 1 x 1 x UR5i v2 Libratum with WiFi Plastic 1 x 1 x 1 x 1 x UR5i v2 Libratum SL Metal 1 x 1 x 1 x 1 x UR5i v2 Libratum SL with WiFi Metal 1 x 1 x 1 x 1 x Table 1: Router versions Figure 2: Front panel UR5i v2L Figure 3: Front panel UR5i v2L with WiFi Figure 4: Front panel UR5i v2L SL Figure 5: Front panel UR5i v2L SL with WiFi 6

  • Advantech UR5i v2 Libratum, 7. TECHNICAL PARAMETERS 7. Technical Parameters 7.1 Basic parameters UR5i v2 Libratum Temperature range Function Storage -40 ◦ C to +75 ◦ C -40 ◦ C to +85 ◦ C Humidity Operating Storage 0 to 95 % relative humidity non condensing 0 to 95 % relative humidity non condensing Altitude Operating 2000 m / 70 kPa Degree of protection IP30 Supply voltage 9 to 36 V DC Consumption Idle GPRS UMTS 2.3 W to 3.5 W (GPRS transmission) to 5.5 W (UMTS/HSDPA transmission) Dimensions Plastic box Metal box 51 x 87 x 116 mm (DIN 35 mm) 42 x 87 x 113 mm (DIN 35 mm) Weight UR5i v2 Libratum – 150 g UR5i v2 Libratum SL �

  • Advantech UR5i v2 Libratum, 9. TROUBLESHOOTING 9. Troubleshooting If you can not connect to the router from your PC, your network card may be configured the way it is not possible to connect to the router. Take one or more of the following steps to solve the problem: • Select the communication rate 10 MB/s in the properties of your network card. • Connect the router to the PC via Switch. • Connect the router to the PC, start the router first and then start the PC after the router’s initialization. 9.1 FAQ - I have NAT enable

  • Advantech UR5i v2 Libratum, 5. ROUTER DESIGN 5.7.5 Ethernet port (ETH0 and ETH1) Panel socket RJ45. Pin Signal mark Description Data flow direction 1 TXD+ Transmit Data – positive pole Input/Output 2 TXD- Transmit Data – negative pole Input/Output 3 RXD+ Receive Data – positive pole Input/Output 4 — — 5 — — 6 RXD- Receive Data – negative pole Input/Output 7 — — 8 — — Table 6: Connection of Ethernet connector Figure 22: Ethernet connector ATTENTION! ETH0 and ETH1 ports are not PoE (Power over Ethernet) compatible! Plug Ethernet cable into the RJ45 connector labeled as ETH0 or ETH1 (see figure below). Figure 23: Connection of ethernet cable 17

  • Advantech UR5i v2 Libratum, 4. CONTENTS OF PACKAGE 4. Contents of Package Basic delivered set of router includes: • router, • power supply, • crossover UTP cable, • up to three external antennas, • clip for the DIN rail, • paper start guide. Figure 1: Contents of package Temperature range for power supply is reduced to 0 ◦ C to +40 ◦ C! 5

  • Advantech UR5i v2 Libratum, 1. SAFETY INSTRUCTION 1. Safety Instruction Please, observe the following instructions: • The router must be used in compliance with all applicable international and national laws and in compliance with any special restrictions regulating the utilization of the router in prescribed applications and environments. • To prevent possible injur y and damage to appliances and to ensure compliance with all relevant provisions, use only the original accessories. Unauthorized modifications or the use of unapproved accessories may result in damage to the router and a breach of applicable regulations. Unauthorized modifications or use of unapproved accessories may void the warranty. • The

  • Advantech UR5i v2 Libratum, 7. TECHNICAL PARAMETERS 7.5 Technical parameters of processor 32b ARM microprocessor Memory 512 Mb DDR SDRAM 128 Mb FLASH 1 Mb MRAM Interface Serial interface RS232 Ethernet interface 10/100 Mbit/s USB 2.0 interface Table 12: Technical parameters of processor 24

  • Advantech UR5i v2 Libratum, 5. ROUTER DESIGN 5.7.4 SIM card reader The SIM card reader for 3 V and 1.8 V SIM cards is placed on the front panel of the router. For getting the router to work is necessary to insert an activated SIM card with an unblocked PIN code. The SIM cards might be of different adjusted APN (Access Point Name). Changing the SIM card: • Before handling of the SIM card disconnect the router from power supply! • Press the small yellow button to eject the reader holder. • Insert the SIM card into the reader holder and slide it

  • 5. ROUTER DESIGN 5.7.6 Reset When PWR LED starts flashing on the front panel, it is possible to restore the default con- figuration of the router by pressing the RST button on the front panel. Af ter pressing this button the default configuration is restored and then router reboots (green LED will be on). For pressing the RST button could be used a narrow screwdriver. Figure 24: Rou

  • Advantech UR5i v2 Libratum, 6. FIRST USE 6.2 Start The router is put into operation when the power supply is connected to this router. By default, the router will automatically start to log on to the default APN. DHCP server will start to assign addresses for devices on the Ethernet port ETH0. Router behavior can be changed via the web interface. This is described in detail in the Configuration manual for v2 routers. The power consumption during receiving is 2.3 W. The peak power consumption during data sending is 5.5 W. However, values of consumption can be increased, if some expansion port is eqquipped. For correct operation it is necessary that the power source is able to

  • 7. TECHNICAL PARAMETERS 7.3 Technical parameters of module HSPA+ module HSPA+ parameters Bit rate 14,4 Mbps (DL) / 5,76 Mbps (UL) 3GPP rel. 6/7 standard Data compress 3GPP UMTS parameters Bit rate 384 kbps (DL) / 384 kbps (UL) 3GPP rel. 4 standard GPRS/EDGE parameters EDGE bit rate 237 kbps (DL) / 237 kbps ∗ (UL) GPRS bit rate 85,6 kbps (DL) / 85,6 kbps ∗ (UL) Multislot class 12, CS

  • Advantech UR5i v2 Libratum, CONTENTS Contents 1 Safety Instruction 2 2 WEEE directive 3 3 Router Description 4 4 Contents of Package 5 5 Router Design 6 5.1 Router versions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 5.2 Delivery identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 5.3 Order codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 5.4 Basic dimensions of the router box . . . . . . . . . . . . . . . . . . . . . . . . . 8 5.

  • 6. FIRST USE Af ter successfully entering login information user gains access to the router via his internet browser. Figure 28: Router web interface A detailed description of the router settings via the Web interface can be found in the document Configuration manual for v2 routers. 6.3.2 Configuration over Telnet For status monitoring, configuration and administration of

  • Advantech UR5i v2 Libratum, 5. ROUTER DESIGN 5.7.3 Antenna connector ANT, DIV (and WIFI) Main and diversity antennas are connected to the router using the SMA connector on the front panel. For UR5i v2 Libratum with WiFi module is also available reverse SMA antenna connector, through which the WIFI antenna can be connected. The router can not operate without connected main antenna marked as ANT ! ANT connector is used to connect the main antenna. For connecting the diver sity antenna use the second antenna connector DIV. If WiFi module is equipped on customer’s request, there is also available WIFI antenna conne

  • 9. TROUBLESHOOTING - Ethernet connection fails or isn’t establishing. • It is possible to turn auto negotiation off and set a rate and duplex manually on the Ethernet interface of the router. - DynDNS doesn’t function. • With private APN this is not functional. • If the same IP address is recorded in your canonic name as dynamically assigned address, it means th

  • Advantech UR5i v2 Libratum, 5. ROUTER DESIGN 5.7 Description of the front panel On the front panel is the following: Caption Connector Description PWR 2-pin Connector for the power supply. ETH0 RJ45 Connector for connection into the local computer network. ETH1 RJ45 Connector for connection into the local computer network. ANT SMA Connector for main antenna. DIV SMA Connector for diversity antenna. WIFI R-SMA Connector for WIFI antenna. Available only when the router is equipped with WIFI module. SIM1 — Holder for the first SIM card. SIM2 — Holder for the second SIM card. Table 3: Fro

  • Advantech UR5i v2 Libratum, 5. ROUTER DESIGN 5.4 Basic dimensions of the router box 5.4.1 Plastic box Figure 7: Basic dimensions of plastic box (bottom and front view) 5.4.2 Metal box Figure 8: Basic dimensions of metal box (bottom and front view) 8

  • Advantech UR5i v2 Libratum, 3. ROUTER DESCRIPTION 3. Router Description HSPA+ router UR5i v2 Libratum is used to wirelessly connect various equipments and devices via Ethernet interface 10/100 to the internet or intranet. Thanks to high data transfer speed of up to 14,4 Mbit/s (download) and 5,76 Mbit/s (upload) it is an ideal wireless solution for traffic and security camera systems, individual computers, LAN networks, automatic teller machines (ATM) and other self-service terminals, etc. As a standard, cellular router UR5i v2 Libratum is equipped with two Ethernet 10/100 and two SIM cards. This wireless router is supplied either in a plastic or metal casing,

  • Advantech UR5i v2 Libratum, 5. ROUTER DESIGN • For every cables we recommend to bind the bunch, we recommend for this use: – Length of the bunch (combination of power supply and data cables) ca n be maxi- mum 1.5 m. If the length of data cables exceeds 1.5 m or in the event of, the cable leads towards the switch – board. We recommend installing over – voltage protec- tors (surge suppressors). – With data cables they mustn’t carry cables with reticular tension ∼ 230 V/50 Hz. Figure 11: Cable routing (plastic) Figure 12: Cable routing (metal) • Sufficient space must be left in fron

  • Advantech UR5i v2 Libratum, 5. ROUTER DESIGN 5.6 Removing from the DIN rail DIN holder is suitable for DIN rail according to EN 60715 standard only. Default position of CPD2 holder (or CKD2 for metal version), which is used for mounting the router on a DIN rail, is shown in the following figure: Figure 15: Default position of DIN holder For removing from the DIN rail it is necessary to lightly push upward the router so that the top part of the CPD2 holder (or CKD2 for metal version) hitched to the DIN rail get out of this rail and then fold out the top part of the router away from the DIN rail. Figure 16: Removing from the DIN rail 11

Related Products and Documents (Network Router):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 JVC BR-DV6000E Instruction manual jvc/br-dv6000e-3GA.pdf 16 Sep 2022 106
2 Quinny buzz Instructions for use & warranty quinny/buzz-NI4.pdf 24 Jan 2023 7 5.4 Mb
3 Crestron TPS-ENET Operations & installation manual crestron/tps-enet-L9N.pdf 25 Aug 2022 28 1.49 Mb
4 Vermont Castings 2490CE Homeowner's installation and operating manual vermont-castings/2490ce-7PJ.pdf 25 Aug 2023 28
5 HP Z1 Specification hp/z1-N74.pdf 20 Jun 2022 39
6 GBC CombBind C150Pro Instruction manual gbc/combbind-c150pro-RFZ.pdf 06 Aug 2022 22 0.9 Mb

Similar Resources:

  • NETGEAR

    FVG318 - ProSafe 802.11g Wireless VPN Firewall 8 Router

    (204 pages)
    202-10121-01 October 2005NETGEAR, Inc.4500 Great America Parkway Santa Clara, CA 95054 USAReference Manual for the ProSafe Wireless 802.11g VPN Firewall Model FVG318 …
  • Linksys

    Instant Broadband Series

    (47 pages)
    Instant Broadband™ SeriesEtherFast®Cable/DSLRoutersUse this User Guide to install the following Linksys product(s):BEFSR41 ver. 2 EtherFast Cable/DSL Router with 10/100 4-Port SwitchBEFSRU31 EtherFast Cable/DSL Router with USB Port and 10/100 3-Port Switch BEFSR11 ver. 2 EtherFast 1-Port Cable/DSL Router User Guide …
  • Black Box

    LGH1006A

    (2 pages)
    724-746-5500 | blackbox.com724-746-5500 | blackbox.com 724-746-5500 | blackbox.comPage 5 Page 6© Copyright 2016. Black Box Corporation. All rights reserved. Black Box and the Double Diamond logo are registered trademarks of BB Technologies, Inc. Any other trademarks mentioned in this manual are acknowledged to be the property of the trade …
  • H3C

    MSR810

    (64 pages)
    H3C MSR 810 Routers Compliance andSafety ManualCompliance and Safety ManualСəйкестік жəне қауіпсіздік ережелеріжөнінде нұсқаулықРуководство по соблюдению требований ибезопасностиПосібник із техніки безпеки та нормативнихвимо …
  • HP

    MSR SERIES

    (682 pages)
    HPE FlexNetwork MSR Router Series Comware 7 Security Configuration Guide Part number: 5998-6958 Software version: CMW710-R0403L02 Document version: 6PW200-20160226 …
  • Sun Microsystems

    StorEdge T3+

    (72 pages)
    Sun Cluster 3.0-3.1 With SunStorEdge T3 or T3+ Array Manualfor Solaris OSSPARC Platform EditionSun Microsystems, Inc.4150 Network CircleSanta Clara, CA 95054U.S.A.Part No: 817–0176–13January 2006, Revision A …

Comments, Questions and Opinions: