Manualios.com

Effekta PEGASUS II 10 KVA Operating Manual

Effekta PEGASUS II 10 KVA Manual Online:

4.7, 2203 votes
Effekta PEGASUS II 10 KVA User Manual
Effekta PEGASUS II 10 KVA User Guide
Effekta PEGASUS II 10 KVA Online Manual

Text of Effekta PEGASUS II 10 KVA User Guide:

  • Effekta PEGASUS II 10 KVA, Rev.A 06/01/2012 109 BLOCK DIAGRAM 1. Input mains (separate for by-pass and rectifier) 2. Rectifier and battery charger 3. Maximum internal battery: 3,3Ah, 7,2Ah and 9Ah – 60 or 62 batteries 4. Optional external battery 5. Inverter 6. Emergency line (by-pass with backfeed contactor) 7. Inverter (SSI) and by-pass (SSB) static switch

  • Effekta PEGASUS II 10 KVA, Installation and start-up of UPS PEGASUS II 10-40 kVA 12 Rev.A 15/05/2012 Index of pictures / Indice delle figure Picture 1 – Rating plate of PEGASUS II ..................................................................................................... 15 Picture 2 – Handling of UPS PEGASUS II ................................................................................................. 23 Picture 3 – Base plan .................................................................................................................................. 25 Pic

  • Effekta PEGASUS II 10 KVA, UPS user manual 102 Rev.A 05/15/2012 Alarm A28 CRITICAL FAULT Description An alarm has been activated which causes the shutdown of part of the UPS (rectifier, inverter, static switch). Possible causes  System failure. Solutions 1. Check which alarms are present and carry out the indicated procedures. 2. If the alarm persists, contact our Technical Support Service. Alarm A29 MAINTENANCE REQ Description It is necessary to carry out maintenance work. Possible c

  • Effekta PEGASUS II 10 KVA, Installation and start-up of UPS PEGASUS II 10-40 kVA Rev.A 15/05/2012 49 4.5.3 Connections The following picture shows the electrical connection between the UPS and the external battery cabinet. Picture 22 – Battery cabinet and UPS connections For the connection above mentioned you can use the cables supplied in the battery cabinet.

  • Effekta PEGASUS II 10 KVA, Rev.A 06/01/2012 121 BLOCK DIAGRAM 1. Common input rectifier and bypass 2. Rectifier and battery charger 3. External battery 4. Inverter 5. Emergency line (optional by-pass with backfeed contactor). 6. Inverter (SSI) and by-pass (SSB) static switch

  • Effekta PEGASUS II 10 KVA, UPS user manual 96 Rev.A 05/15/2012 8.2 TROUBLESHOOTING Alarm A1 MAINS FAULT Description The voltage or frequency of the input line are out of tolerance. Possible causes  Mains instability or failure.  Wrong phase rotation. Solutions 1. Check the connections to the mains. 2. Check the stability of mains voltage. 3. If the alarm persists, contact our Technical Support Service. Alarm A2 INPUT WRONG SEQ Description The phase rotation on the rectifier input line

  • Effekta PEGASUS II 10 KVA, Installation and start-up of UPS PEGASUS II 10-40 kVA Rev.A 15/05/2012 23 3.2 HANDLING OF THE UPS The UPS is packed on a pallet. It is handled from the transport vehicle to the installation (or storage) place via a fork lift. The device has a heavy weight  Avoid turnover during the transport of the UPS.  Cabinets must always be handled in upright position.  During loading and unloading operations, always respect the indications regarding the device barycentre marked on the package. Before positioning the UPS, in order to avoid risks of turnover, it’s recommended to move the system

  • Effekta PEGASUS II 10 KVA, Installation and start-up of UPS PEGASUS II 10-40 kVA Rev.A 15/05/2012 19 Injury hazard due to electric shock! The device is subject to high voltages, thus all safety instructions must be scrupulously adhered to before performing any operation on UPS PEGASUS II:  Isolate the battery via DC circuit breakers before connecting it to the UPS;  Connect the ground cable to the relevant bar before carrying out any other connection inside the device. Injury hazard due

  • Effekta PEGASUS II 10 KVA, 112 Rev.A 06/01/2012 UPS OUTPUT: BY PASS Automatic static by-pass Electronic thyristor switch Protection Fuses Bypass Vac Single phase Nominal Voltage (selectable) Range Vac % 220 – 230 – 240 ±10 Nominal Frequency (selectable) Range Hz % 50-60 ± (1 5) adjustable Transfer mode Without break Transfer inverter  automatic bypass In case of : - Short circuit - Battery end of discharge - Inverter test - Inverter not operating Retransfer automatic bypass  inverter - Automatic - Block on bypass after 6 transfers within 2 minut

  • Effekta PEGASUS II 10 KVA, Rev.A 06/01/2012 115 BLOCK DIAGRAM 1. Input mains (separate for by-pass and rectifier) 2. Rectifier and battery charger 3. Maximum internal battery: 3,3Ah, 7,2Ah and 9Ah – 60 or 62 batteries 4. Optional external battery 5. Inverter 6. Emergency line (by-pass with backfeed contactor) 7. Inverter (SSI) and by-pass (SSB) static switch

  • Installation and start-up of UPS PEGASUS II 10-40 kVA 28 Rev.A 15/05/2012 3.3.3 Environmental installation conditions The air is classified by the EN 60721-3-3 standard (Classification of environmental parameters and their severities – Stationary use at weather-protected locations) based on climatic and biological conditions as well as on mechan

  • UPS user manual Rev.A 05/15/2012 81 STATUSES S1 BOOSTER OK S2 BATTERY OK S3 INVERTER OK S4 INVERTER --> LOAD S5 INV BYPASS SYNC S6 BYPASS OK S7 BYPASS --> LOAD S8 BOOST CHARGE S9 INV MASTER SYNC

  • Effekta PEGASUS II 10 KVA, UPS user manual 94 Rev.A 05/15/2012 8.1 OPERATING STATUS DEFINITION Status S1 BOOSTER OK Description The rectifier section is working properly. Operating condition The rectifier supplies the inverter and keeps the battery charged. Status S2 BATTERY OK Description The battery is connected to the UPS. Operating condition The battery is kept charged by the rectifier and is ready to feed the inverter. Status S3 INVERTER OK Description The inverter voltage and frequency are within the allowed range. Operating condition The inverter is r

  • Effekta PEGASUS II 10 KVA, UPS user manual Rev.A 05/15/2012 79 5.3.1 Display of alarms history All the events are recorded in the alarms history. UPS STATUS HISTORY HISTORY: xxx/yyy Alarm code Date/time The first event shown is the latest one in order of time; a new event makes all the other events automatically shift one position, clearing the oldest event. The quantity of stored events is displayed on the first line (xxx/yyy), which contains the data currently d

  • Effekta PEGASUS II 10 KVA, UPS user manual 74 Rev.A 05/15/2012 LED 1 GREEN AC line on rectifier input within tolerance GREEN Wrong phase rotation OFF AC mains failure on rectifier input LED 2 GREEN AC bypass line within tolerance GREEN Wrong phase rotation OFF AC bypass line out of tolerance AC bypass line failure LED 3 GREEN Rectifier off or faulty RED DC voltage out of tolerance GREEN Rectifier on and DC voltage within tolerance LED 4 GREEN circuit breaker BCB closed and battery charging GREEN Batte

  • Effekta PEGASUS II 10 KVA, UPS user manual 92 Rev.A 05/15/2012 7.1.5 Message statistics The statistics section regarding the messages exchanged on the communication buses consists of three different menus. CAN STATISTICS SSW MSG RX: 32564 100.0% Number of messages received and percentage of reception accuracy regarding the status of the static switches. The messages are exchanged between all the UPS units, therefore the number will increa

  • Effekta PEGASUS II 10 KVA, Installation and start-up of UPS PEGASUS II 10-40 kVA 10 Rev.A 15/05/2012 INSTALLATION AND START-UP OF UPS PEGASUS II 10-40KVA Index 1 SCOPE .............................................................................................. 13 2 SAFETY RULES AND WARNINGS .................................................. 14 2.1 UPS USE.................................................................................................................. 14 2.2 PEGASUS II RATING .............................................................................................. 15 2.3 SPECIAL SAFETY WARNINGS ..................

  • Effekta PEGASUS II 10 KVA, 108 Rev.A 06/01/2012 TECHNICAL DATA SHEET “PEGASUS II” 10 – 15 – 20 kVA 3Ph(In) – 1Ph(Out) GENERAL INFORMATION POWER kVA 10 15 20 UPS Type ON LINE – Double Conversion Nominal output power (Cos 0,8) kVA 10 15 20 Nominal output power (Cos 1,0) kW 8 12 16 Efficiency (AC AC) (ON LINE - Double Conversion) @25% load @50% load @75% load @100% load % > 88 > 90 > 91 > 92 Efficiency (AC AC) (Eco Mode) % > 98

  • Effekta PEGASUS II 10 KVA, Installation and start-up of UPS PEGASUS II 10-40 kVA 14 Rev.A 15/05/2012 2 SAFETY RULES AND WARNINGS 2.1 UPS USE Congratulations on choosing a product from EFFEKTA ® for the safety of your equipment. To obtain the best performance from your PEGASUS II UPS system (Uninterruptible Power Supply), we suggest that you take your time to read the following manual. The purpose of this manual is to give a short description of the parts composing the UPS and to guide the

  • Rev.A 06/01/2012 125 OPTIONS 1. BATTERY TEMPERATURE VOLTAGE COMPENSATION 2. INSULATION TRANSFORMER ON BY-PASS 3. SEPARETED INPUT KIT 4. VOLTAGE ADAPTATION AUTO-TRANSFORMERS 5. BACK FEED PROTECTION 6. RELAY CARD (Eight signals Alarms/Statuses), Free relay contact 7. SERIAL INTERFACE RS-485 (MOD-BUS protocol) 8. SNMP ADAPTER 9. REMOTE

  • Effekta PEGASUS II 10 KVA, 122 Rev.A 06/01/2012 UPS INPUT: RECTIFIER AND BATTERY CHARGER POWER kVA 30 40 Input Three-phase + Neutral Nominal input voltage range Vac % 400 -20/+15 Input frequency range Hz % 50 – 60 ±5 Input power factor > 0.99 Input current THD at nominal voltage and THDV <0,5% @25% load @50% load @75% load @100% load % < 14 < 7 < 5 < 4 DC output voltage accuracy % +/- 1% DC output voltage ripple % rms 1% rms Battery recharging characteristic IU (DIN 41773) Maximum recharging current

  • Effekta PEGASUS II 10 KVA, Installation and start-up of UPS PEGASUS II 10-40 kVA Rev.A 15/05/2012 15 2.2 PEGASUS II RATING UPS PEGASUS II is provided with an identification plate containing the operation ratings. The plate is fixed outside, on the rear of UPS. Picture 1 – Rating plate of PEGASUS II Check the technical characteristics Before carrying out any installation or start-up operation on the UPS, make sure its technical characteristics are compatible with the AC supply line and with the output loads.

Related Products and Documents (UPS):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 SunBriteTV SB-AW-6-BLK Owner's manual sunbritetv/sb-aw-6-blk-28P.pdf 25 Feb 2023 2
2 Philips DLA1273 Brochure philips/dla1273-3L8.pdf 19 Jul 2022 2
3 Philips AZ6836 - Cd Portable Bedienungsanleitung magnavox/az6836-cd-portable-KN1.pdf 05 Feb 2023 18
4 Ikegami PM-129 Instruction manual ikegami/pm-129-5ZI.pdf 21 Aug 2023 10
5 AEG EN 64 TM Operating instructions manual aeg/en-64-tm-74O.pdf 13 Nov 2022 24 0.95 Mb
6 GE Monogram ZIS360NR Technical service manual ge/monogram-zis360nr-F76.pdf 11 Aug 2023 63

Similar Resources:

  • Tripp Lite

    SMX2200XLRT2U

    (60 pages)
    Owner’s Manual1111 W. 35th Street Chicago, IL 60609 USACustomer Support: (773) 869-1234 • www.tripplite.comImportant Safety Instructions2Mounting3Quick Installation5Basic Operation7Storage and Service11EspañolCopyright ©2006 Tripp Lite. All rights reserved. SmartPro®is a trademark of Tripp LiteSmartPro®Intelligent, Line-Interactive UPS System• 220 …
  • Salicru

    SPS.750.ADV RT

    (2 pages)
    7SPS ADVANCE RT QUICK START GUIDEQSG_SPS ADVANCE RT_V03_062015QUICK START GUIDE- SPS.750.ADV RT- SPS.1000.ADV RT- SPS.1500.ADV RT- SPS.2000.ADV RT- SPS.3000.ADV RT8CODE [email protected]+34 93 848 24 001x1x 2x2x2x 8xA1xCDEB21!support.salicru.com±2”INPUT 220-240V~LS1 OUT PUT 250V~ 10ALS2 OUT PUT 250V~ 10AIN OUTRS232USBEPOIN …
  • Tripp Lite

    SMX1000LCD

    (5 pages)
    SmartPro 230V 1kVA 500W Line-Interactive UPS,Tower, LCD, USB, 6 OutletsMODEL NUMBER: SMX1000LCDProtects connected mission-critical equipment against damage, downtime and data loss due to blackouts,brownouts, power surges and line noise. Ideal for home/office workstations, media centers and homeentertainment systems.DescriptionThe SMX1000LCD SmartPro 230V 1kV …
  • Phasak

    PH 9465

    (21 pages)
    SERIE INTERACTIVE [ES] PH 9465 PH 9469 PH 9485 LEA AL MENOS ESTO Siga estrictamente todas las advertencias e instrucciones de este manual. Antes de instalar esta unidad, lea todas las instrucciones atentamente. No utilice este SAI antes de leer atentamente toda la información de seguridad y las ins …
  • Belkin

    F6HXXX-USB-C

    (2 pages)
    INTRODUCTION Thank you for purchasing a Belkin Uninterruptible Power Supply (UPS). Each year, several natural and man made occurrences put the power supplied to your electronics in your home or office in jeopardy. At risk are your hardware, software and data because of these power problems. …
  • IBM

    11000VA

    (12 pages)
    򔻐򗗠򙳰 Rack Installation InstructionsFor the 11000 VA 5U uninterruptible power supply and 11000VA 3U extended battery moduleUse the instructions in this document to install the IBM®11000 VA LCD 5U Rack UPS and IBM 11000 VAUPS 3U Extended Battery Module in a rack cabinet.Review the documentation that comes with your rack cabinet for safety and cabling …

Comments, Questions and Opinions: