Falcon DRC376 v1648-02 Operation & User’s Manual
|
Falcon DRC376 v1648-02, 9 Step 5 When charging is complete, reinstall the battery in its bay, reconnect the power plug from the battery to the craft, and close the battery cover. Be sure to match the plugs correctly and securely close the battery cover or damage may occur. Reminder: Do not charge batteries overnight. Do not leave batteries unattended while charging. Step 4 Plug the charging cable into the USB port of a powered ON computer or USB power adapter (not included). The battery will now charge. LIGHT STATUS Red Light ON Charging Red Light OFF Ready AC/DC Charger Status
19 Consult this table for further troubleshooting assistance. PROBLEM POSSIBLE CAUSES SOLUTION Craft is unresponsive • No power to remote or craft • Poor contact between power plugs • Craft is out of range • Check remote batteries, replace if needed • Check craft’s battery, be sure it is fully charged • Be sure the power plugs are rmly connected •
Falcon DRC376 v1648-02, 15 Craft will perform ip in the desired direction. Press the Right Control Stick down (into the remote) then move the Right Control Stick in any direction. Headless Mode Headless Mode changes the default orientation of the craft, where the red LEDs/red rotors indicate the front of the craft. Instead, the craft will reorient its “front” based on the rst Right Control Stick input from the user. This can be useful if you become disoriented while ying, or cannot visually determine which direction is “true front”. To activate Headle
Falcon DRC376 v1648-02, 23 International Support To download this User’s Guide in English, Spanish, and French, or to get answers to frequently asked questions, visit the support section at: www.gpx.com Para descargar este Manual del Usuario en inglés, español y francés, o para obtener respuestas a preguntas frecuentes, visite la sección de apoyo en: www.gpx.com Pour télécharger ce guide de l’utilisateur en anglais, espagnol ou français, ou pour obtenir des réponses à des questions fréquemment posées,
Falcon DRC376 v1648-02, 12 Setting Trim & Countering Drift Even after the craft is calibrated, it may show a tendency to drift while airborne. Adjusting the trim will help counter this effect and allow you to better control the craft. To avoid potential damage, adjust the trim while in a stable hover, and do not make any sudden movements with the ight controls. Adjust one trim setting at a time to avoid confusion. Remember, the red LEDs /red rotors indicate the front of the craft. While adjusting the trim will help with drift, it is not guaranteed to eliminate it entirely. Physical, mech
14 Tips for Safe Operation • Only y in large, open spaces, such as a eld or a very large indoor area, free of obstacles like power lines, trees, ceiling fans, etc. • When ying indoors, avoid walls and ceilings, as the craft will be drawn towards them if closer than 2 to 3 feet. • Stand behind the craft when rst taking off, so that it and you are
Falcon DRC376 v1648-02, 16 Make sure the remote and the craft have been successfully paired and the Micro-SD card is installed in the camera before attempting to use. Video To record video, press and hold the Photo/Video button. The green light in camera will blink red for as long as video is recording. Press the Photo/Video button again to stop recording video, the light in the camera will turn back to green. Photos To take a single image, press the Photo/Video button once. The green light in camera will blink red
Falcon DRC376 v1648-02, 17 Remove Micro-SD card from camera and connect to included USB adapter. Be sure to insert correctly or damage may occur. Gently push against the Micro-SD card until it clicks into or out of the card slot. Be sure to insert correctly or damage may occur. Connect to a USB port of a computer. Use the computer’s le browser to access photos and videos. SD Card Install & Removal View Photos/Video on a Computer
Falcon DRC376 v1648-02, 11 PHOTO/ VIDEO PITCH HEADLESS/ AUTO REV POWER Step 4 Push the Left Control Stick directly forward, wait for a chime to sound, then pull the stick directly backward, and wait for a second chime. When this last chime has sounded, the craft is calibrated and ready to y. Step 5 Attempt a stable hover, low to the surface you started on. If you notice a tendency to drift, you may need to adjust the trim controls to ne tune the handling (see Trim Adjustment, pg. 12). When You’re Done Flying... After safely landing, keep the throttle in the lowest position (OFF) and wait for the rotors to stop
Falcon DRC376 v1648-02, 10 Pre-Flight Calibration PHOTO/ VIDEO PITCH HEADLESS/ AUTO REV POWER Craft/Remote Link Before ying, the craft and the remote must be linked together, and the gyroscopes on the craft must be allowed to calibrate to ensure smooth and level ight. Begin with the craft and remote powered OFF. Step 3 Power the remote control ON. The light on the remote will blink as it searches for the signal from the craft. An audible chime will sound when the remote and the craft have successfully linked with each other. Step 1 Place the craft on a at and level surface. Step 2 Power the craft ON. The LED lights will blink in unison as the craft searches for a signal from the
Falcon DRC376 v1648-02, 2 Warnings & Precautions Important Safety Instructions • Read and follow all instructions. • Keep these instructions for future reference. • Heed all Warnings. • Intended for children ages 14 and higher. Adult supervision is required. • Only use attachments/accessories specied by the manufacturer. • Before ying, always check the body, rotors, and battery for any damage or obstructions. • Battery should be free from cracks or swelling. • Keep the rotors clear of any obstructions and body parts to avoid potential damage and injury. • Manufacturer and de
Falcon DRC376 v1648-02, 3 Table of Contents Sky Rider Falcon Pro – 4 Features Includes Orientation – 5 Overview Remote – 6 Remote Functions Remote Battery Installation Charging the Battery – 8 Battery Charging Procedure Pre-Flight Calibration – 10 Craft/Remote Link When You’re Done Flying... Trim Adjustment – 12 Setting Trim & Countering Drift Flying Tips & Features – 14 Tips for Safe Operation Speed Setting Flips & Tricks Headless Mode Auto-Reverse Camera & Memory Card – 16 Video Photos SD Card Install & Removal View Photos/Video on a Computer Troubleshooting – 18 Gyrosc
Falcon DRC376 v1648-02, 6 Left Control Stick Increase Throttle: push forward Decrease Throttle: pull backward Yaw/Spin: push left/right Speed Setting: press down to change speed Right Control Stick Pitch: push forward/backward Roll/Bank: push left/right Photo/Video Press to take a photo. Press and hold to take video. Headless Mode/ Auto Reverse Press to enter headless mode. Press and hold to make the craft y in reverse. Roll Trim Correct left/right drift. Yaw Trim Correct left/right rotational drift. Pitch Trim Correct forward/ backward drift. Power Switch Power/Status Indicator Remote Functions Remote
Falcon DRC376 v1648-02, 18 Restore Factory Settings If the craft is still experiencing difculty ying or is behaving erratically, the craft and remote may need to have the factory default settings restored. Do not attempt to do this while ying. Safely land the craft before attempting this procedure. Pull both control sticks to the lowest left position for 2-3 seconds. When the LED lights start blinking, release the controls sticks. When the LED lights have turned solid, the factory reset is complete and the craft is ready to y. Gy
Falcon DRC376 v1648-02, 20 Repair Rotor Replacement The craft comes with 4 replacement rotors, to be used if the originals are broken or badly damaged. To replace a rotor, use a small Phillips head screwdriver (included) and remove the screw connecting the rotor to the electric motor shaft. Remove the damaged rotor and replace it with a new one, then screw it back into place on the motor shaft, taking special care not to bend or break the shaft. REMINDER: It is extremely important to use the correct rotor (red or white) for replacement. Mismatching the rotor will cause the craft’s ight to be erratic and difcult to control. REMINDER: Pilots are respon
Falcon DRC376 v1648-02, 21 Parts Replacement If any major components of the craft are damaged beyond repair, use the contact information on the next page to order replacements. The following parts are available for order. Parts
Falcon DRC376 v1648-02, 8 Charging the Battery Battery Charging Procedure The craft’s lithium-polymer (Li-Po) battery must be charged before the unit can be own. Before charging, be sure the craft and remote control are powered off. This will reduce the chance of damage or injury. Step 1 Make sure the craft is powered OFF, then remove the battery cover. Step 3 Attach the plug on the battery to the plug on the charging cable. Be sure to match the plugs correctly or damage may occur. Step 2 Disconnect the power plug con
Falcon DRC376 v1648-02, 4 Features • 360° ips & tricks • 2 speed settings • 6-axis gyroscope • .3 MP Camera (photo & video) with SD card slot • Control distance: up to 150 feet • Headless Mode • Auto-Reverse • LED navigation lights • Operating time: 6-8 minutes • Charge time: 60-80 minutes Includes • 2.4 GHz remote control: requires 4 AAA batteries (not included) • Built-in rechargeable lithium polymer battery • USB cable for battery recharge • 4GB SD card • Screwdriver • 4 replacement rotors • User’s guide & warranty Sky Rider Falcon Pro
Lynxmotion HQuad500 Quadcopters Assembly manual
HQuad500 |
Lumenier Hydra Edition QAV210 Quadcopters Quick start manual
Hydra Edition QAV210 |
LotusRC T580P+ Quadcopters Operation & user’s manual
T580P+ |
ACME zoopa q roonin 155 Quadcopters Instruction manual
zoopa q roonin 155 |
Ares RECON HD Quadcopters Owner's manual
RECON HD |
Udi U817 Quadcopters Operation & user’s manual
U817 |
PILOTAGE NANO-X Quadcopters Operation & user’s manual
NANO-X |
Parallax ELEV-8 Quadcopters Information and assembly manual
ELEV-8 |
# | Manufacturer | Model | Document Type | File | Updated | Pages | Size |
---|---|---|---|---|---|---|---|
1 | McCulloch | 12592RB | Instruction manual | mcculloch/12592rb-6RE.pdf | 12 Feb 2023 | 84 | |
2 | GPX | CR1807 | Instruction manual | gpx/cr1807-UP6.pdf | 23 Apr 2023 | 2 | 0.71 Mb |
3 | Cypress | CH-106TX | Operation manual | cypress/ch-106tx-7L6.pdf | 27 Dec 2023 | 10 | 1.02 Mb |
4 | Philips | PCVC665K | Owner's manual | philips/pcvc665k-RPX.pdf | 08 Sep 2023 | 25 | 1.38 Mb |
5 | American Dryer Corp. | Gas DSI/HSI/Electric/Steam/Phase 7 with S.A.F.E. D-40 | Installation manual | american-dryer-corp/gas-dsi-hsi-electric-steam-phase-7-with-s-a-f-e-d-40-29O.pdf | 04 Aug 2023 | 62 | 0.74 Mb |
6 | Alpine | CDA-7873R | Owner's manual | alpine/cda-7873r-B7M.pdf | 05 Aug 2022 | 44 | 0.51 Mb |
MiDRONE
MiDRONE SKY 180GUIDE DE L'UTILISATEUR* Cette image est montrée pour exemple uniquement. Veuillez vous référer au produit réel.INTRODUCTIONNous vous remercions pour l'achat de ce produit. Ce drone est équipé d'une caméra qui vous permettra de prendre des photos et vidéo pendant le vol. Il peut être piloté soit avec la télécommande j …
SKY 180(65 pages) |
Carrera
Made in China, ShantouMontage- und BetriebsanleitungAssembly and operating instructionsInstructions de montage et d’utilisationInstrucciones de montaje y de servicioIstruzioni per il montaggio e l’usoMontage- en gebruiksaanwijzingInstruções de montagem e modo de utilizaçãoMonterings- och bruksanvisningAsennus- ja käyttöohjeInstrukcja montażu i obs …
RC(14 pages) |
Giros
PTIDADE 14+ Drone Quad Copter R/C MANUAL DE INSTRUÇÕESCaracterísticas PrincipaisEstrutura de quatro eixos, o que faz com que o helicóptero funcione de forma � …
SYM0X4(36 pages) |
Reely
BedienungsanleitungRace Copter „DIY X-79“ RtF Best.-Nr. 1642420 Seite 2 - 18Operating Instructions“DIY X-79” RtF Race Copter Item No. 1642420 Page 19 - 35 Mode d’emploiRace Copter «DIY X-79» RtFN° de commande 1642420 Page 36 - 52GebruiksaanwijzingRace Copter „DIY X-79“ RtFBestelnr. 1642420 Pagina 53 - 69
…
DIY X-79(72 pages) |
Parrot
Quick start guide Guide de démarrage rapideGuía de inicio rápidoKurzanleitungGuida di avvio rapdiaQuick start gidsGuia de início rápidoMCPKGmiloslivret.indd 1 07/12/2015 11:38:20
…
bebop 2(43 pages) |
DEMA
Matrice 2x0 V2 ● Product How are the M200 Series and M200 Series V2 drones different visually? The M200 Series V2 drones have new anti-collision beacons on the aircraft shell and at the bottom of the battery compartment. The V2 arm lights are equipped with optical lenses, and the engraving on the body of the drone shows V2. Can I switch the dual downward …
Matrice 2x0 V2(4 pages) |
Linear Smoke Alarm DXS-73Smoke Alarm Installation instructions (Linear DXS-73) DXS-73, 2 |
YURAKU Other YUR.PHOTO 102M4Other #5X3ZJU YUR.PHOTO 102M4, 2 |
MyGica Set-top boxes ATV1800EMyGica Set-top boxes Quick start manual (File: mygica-atv1800e-quick-start-manual-20, 21st Oct 2023) ATV1800E, 20 |
KANSAI SPECIAL Sewing Machine BLX2202PCManual: KANSAI SPECIAL BLX2202PC (BENOTV, Upd.Sun 11.2023) BLX2202PC, 24 |
Whelen Engineering Company Other ION IONBKT2Whelen Engineering Company Other Installation manual (File: whelen-engineering-company-ion-ionbkt2-installation-manual-2, 06/12/2023) ION IONBKT2, 2 |
Korg Synthesizer MONOLOGUEPDF Guide (@S84268), Korg MONOLOGUE Synthesizer (11th Jan 2024) MONOLOGUE, 5 |
NEC Monitor X754HBX754HB Installation manual - 6R1ZF5 X754HB, 11 |
DAVIS Humidifier Vantage Pro2DAVIS Humidifier Vantage Pro2 Console manual Vantage Pro2, 56 |
JUKI Sewing Machine MB-372JUKI MB-372 Guide (Instruction book), @JIRVPU MB-372, 33 |
Challenge Trimmer HTEG34C-450#1QRO63: HTEG34C-450 Trimmer Operating instructions manual HTEG34C-450, 7 |
KROHNE Transmitter TT 51 SeriesTransmitter Handbook (KROHNE TT 51 Series) TT 51 Series, 56 |
Welch Allyn Medical Equipment PROPAQ CS#77657J PROPAQ CS: Welch Allyn Medical Equipment Owner Documentation PROPAQ CS, 23 |