Manualios.com

Digitus DN-7060 Quick Installation Manual

Digitus DN-7060 Manual Online:

4.45, 2381 votes
Digitus DN-7060 User Manual
Digitus DN-7060 User Guide
Digitus DN-7060 Online Manual

Text of Digitus DN-7060 User Guide:

  • Digitus DN-7060, 1 1. Product Introduction Congratulations on purchasing this Wireless N ADSL2/2+ Router. This router is a cost-effective ADSL2+ router, with the combination of an ADSL2+ modem, router, Ethernet network switch and wireless access point, you can surf the Internet through your ADSL2/2+ broadband connection without investing other devices. This router can support downstream transmission rates of up to 24Mbps and upstream transmission rates of up to 1Mbps. It supports PPPoA (RFC 2364 - PPP over ATM Adaptation Layer 5),

  • Digitus DN-7060, 2 2. Minimum Requirements The following devices are necessary to configure and use the ADSL2+ Router:  A PC with Pre-installed Ethernet Adapter (Required) and a Web-Browser (Internet Explorer 4.0 or higher)  RJ-45 Ethernet crossover cable (Included in the package)  RJ-11 (ADSL Ready) phone Line 3. Product Package This package contains the following components:  One ADSL2/2+ Router (Annex A or B)  One Power Adapter  One RJ-45 Ethernet Cable (100 cm)  One RJ-11 Telephone

  • Digitus DN-7060, 3 4. Install ADSL Router Step 1. Connect the ADSL Line Connect the router to your ADSL cable through the supplied RJ-11 telephone line. Step 2. Connect the router to your LAN network Connect the router to your PC, hub or switch by attached the Ethernet cable to the LAN port of the router. Step 3. Connect the Power Adapter to the Router Connect the power adapter to the power jack on the rear panel of router. Step4: Check the ADSL LED on the Router The ADSL LED will be ON if the router is connected to the ADSL cable and receives the ADSL signals successfully. If the LED is blinkin

  • Digitus DN-7060, 4 5. Setup Wizard This router provides a Setup Wizard tool for user to configure the ADSL settings. This wizard collects some ISP’s ADSL settings so that user can easy to configure the router’s ADSL settings by only selecting the ISP vendor from the wizard. If you cannot find your ISP from the list in the wizard, please manually set the ISP information through the wizard. Getting Started Before you start, please check the following items: 1. Please make sure that you have connected the ADSL cable to the router correctly. When the ADSL cable is worked normally, the ADSL LED will be on.

  • 5 2. The following screen will be displayed. Click “Setup Wizard”. 3. This wizard will be executed and try to search for the ADSL Router. If the ADSL Router can be searched successfully, the wizard will guide you to step 5.

  • Digitus DN-7060, 6 4. If the router cannot be found, please enter the IP Address and the Password of the router to search again. Click “Next” to continue. 5. The wizard will automatically select the country where you are in by checking the language of the operating system in your computer and skip to the “Select ISP” page. Please select the ISP. If you cannot find the ISP, please click “Other” to reselect the country or manual configure the ISP information.

  • Digitus DN-7060, 7 5.1 Automatically Set ISP If you can find the ISP from the wizard, please follow the procedures below to let the wizard set the ISP settings automatically. 1. Please select the ISP (Internet Service Provider) of your ADSL service. 2. Enter the Username and Password which your ISP has provided to you if it is needed. Click “Next”.

  • Digitus DN-7060, 8 3. Click “Save” to save the settings and reboot the router. 4. After saving and rebooting the router, the ISP settings are all finished. This wizard will then help to set your computer to obtain IP Address from the router automatically. Note1: To use the router to get into the Internet, the IP Address of each PC has to be set in the same network segment as the router. This wizard will help to set the proper IP Address to your computer. Note2: By default, the router’s DHCP Server is enabled. If it is disabled before running the wizard, the wizard will enable the DHCP Server of the router automatically.

  • Digitus DN-7060, 10 6. If you can successfully to connect to the ISP, you will see below page. If you want to configure more settings, please click “Advanced Settings” to get into the web management of the router or click “Finish” to close the wizard.

  • Digitus DN-7060, 11 5.2 Manually Set ISP If you cannot find the ISP from the wizard, please follow the procedures below to set the ISP settings manually. Before configuring the ISP manually, please check with your ISP (Internet Service Provider) what kind of the service is provided such as PPPoE, PPPoA or RFC1483/2684. Gather the information as illustrated in the following table and keep it for reference. PPPoE VPI/VCI, VC-based/LLC-based multiplexing, Username, Password (and Service Name). PPPoA VP

  • 12 2. Please check with your ISP the connection type of the ADSL line. Select the Connection Type and click “Next”. Note: The wizard will automatically select the country where you are in by checking the language of the operating system in your computer and skip to the “Select ISP” page. If you want to change the country, please click “Back” from this page. 3. In

  • Digitus DN-7060, 14 5. Click “Save” to save the settings and reboot the router. 6. After saving and rebooting the router, the ISP settings are all finished. This wizard will then help to set your computer to obtain IP Address from the router automatically. Note1: To use the router to get into the Internet, the IP Address of each PC has to be set in the same network segment as the router. This wizard will help to set the proper IP Address to your computer. Note2: By default, the router’s DHCP Server is enabled. If it is disabled before running the wizard, the wizard will

  • Digitus DN-7060, 16 8. If you can successfully to connect to the ISP, you will see below page. If you want to configure more settings, please click “Advanced Settings” to get into the web management of the router or click “Finish” to close the wizard.

Related Products and Documents (Wireless Router):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 RTI VMX-8 Operation & user’s manual rti/vmx-8-B12.pdf 18 Dec 2023 32
2 Impact Acoustics Video/Stereo Audio Distribution Amplifier Operation & user’s manual impact-acoustics/video-stereo-audio-distribution-amplifier-W8B.pdf 19 Mar 2023 2
3 Braun 7280 Operation & user’s manual braun/7280-9I3.pdf 05 Jan 2023 53 7.52 Mb
4 MTX MTX MZS1004 Specifications mtx/mtx-mzs1004-74A.pdf 16 May 2023 4
5 Cuisinart SM-FPC Instruction/recipe booklet cuisinart/sm-fpc-BEW.pdf 30 Sep 2022 7
6 Russell Hobbs RHM1707B Instruction manual russell-hobbs/rhm1707b-K4O.pdf 13 Aug 2022 13 1.09 Mb

Similar Resources:

  • AKG

    SR 40 SINGLE

    (60 pages)
    BEDIENUNGSANLEITUNG . .S. 2Bitte vor Inbetriebnahme des Gerätes lesen!USER INSTRUCTIONS . . . . . . . .p. 12Please read the manual before using the equipment!MODE D’EMPLOI . . . . . . . . . . . . . . . .p. 21Veuillez lire cette notice avant d’utiliser le système!ISTRUZIONI PER L’USO . . . . .p. 30Prima di utilizzare l’apparecchio, leggere il manua …
  • JACS

    TD0301

    (28 pages)
    TD0301 User Manual Interface Key Button Key Illustrate Power On/Off, power on after press 3 seconds; power off after press 3 seconds WPS On/Off, enable/disable the WPS function of Wi-Fi after press 3 seconds Reset Software reset after short click Reload to default settings after press 6 seconds Hardware reset after press 12 seconds LED Indication Ind …
  • ZyXEL Communications

    AMG1302-11C

    (2 pages)
    Using the Blue Ethernet cable, connect the LAN port of the Fibre Unit (ONT) to the blue port labelled “WAN” on the back of the routerPlug the power supply unit into the wall socket and connect the small round plug from the power supply unit into the power socket on the back of the router. Switch the power on at the wall socket and press the red po …
  • NETGEAR

    R7500

    (22 pages)
    Quick StartNighthawk X4 AC2350 Smart WiFi RouterModel R7500SupportThank you for purchasing this NETGEAR product.Aer installing your device, locate the serial number on the label of your product and use it to register your product at https://my.netgear.com. You must register your product before you can use NETGEAR telephone support. NETGEAR recommends regi …
  • Riptide

    Cradlepoint COR IBR200

    (9 pages)
    ©2018 Riptide - Put Your Facilities on Autopilot. All rights reserved. riptideio.comProcessorIntel® Atom™ E3805 dual coreSpeed / Cache1.33 GHz / 1 MBI/O1 x 10/100 Fast Ethernet (RJ-45) with PoE (15.4W)Serial Interfaces: 2 x RS-232/422/485.GPIO Multi-function I/O: 0-5V, 8 channel, independently programmable, DAC, ADC. Optional ZigBee module.I/O (All model …
  • ZyXEL Communications

    NBG6604

    (4 pages)
    ENGLISH | DEUTSCH | FRANÇAIS | ITALIANO | ESPAÑOL | NEDERLANDSNBG6604AC1200 Dual-Band Wireless RouterQuick Start GuidePower outlet2Modem 1NBG6604Login Password1234http://myrouterLoginhttp://myrouterLogin Password: 1234(default)Ethernet Cable Connection Power On5G On 2.4G OnWait for the LEDs to turn on.3-13-24Wi-Fi Connection Configure Your Device …

Comments, Questions and Opinions: