Firelands X BOLT 250 Assembly Manual

Text of Firelands X BOLT 250 User Guide:

• Firelands X BOLT 250, Assembly Manual Product specications are subject to change without notice. Due to ongoing development, the actual product may vary from images shown. This product is not a toy! (14+) Recommended for ages 14 and up. Adult supervision required for ages under 18 years old. Contains small parts, keep out of reach of children 3 years of age and younger. Distributed in the UK by: J Perkins Distribution Ltd, Lenham, Kent, UK ME17 2DL. www.jperkins.com Distributed in Australia by: Model Engines (Aust.) Pty. Ltd., Unit 1, 158-168 Browns Road,

• Firelands X BOLT 250, 1 x X Bolt Frame (9 pieces) 1 x Flight Controller 1 x Power Distribution 1 x FPV Video Camera 1 x FPV Video Transmitter 4 x 18A Spreed Controls 4 x 2206 2250Kv Brushless Motors 1 x Battery Strap 2 x CW Prop 2 x CCW Prop 6 x 10mm Nylon Standos (F/F) 4 x 12mm Nylon Standos (M/F) 2 x 15mm Nylon Standos (M/F) 4 x Plastic M3 Hex Nuts 8 x 20mm M3 Screws 25 x 6mm M3 Screws 2 x 6mm M3 Grub Screw 4 x M3 Aluminum Thumb Nut 8 x M3 Aluminum 10mm Standos 2 x M3 Aluminum 23mm Standos 2 x M3 Aluminum 35

• Forward 1 2 3 4 5 6 1. Camera Plate 2. Battery Plate 3. Top Plate 4. Bottom Plate 5. Camera Mount 6. Motor Arms Carbon Parts Washers On the bottom frame insert four M3 6mm screws. Use four washers to keep the PDB (Power Distribution Board) from touching the carbon frame. Place the PDB. Orient the PDB so that the solder pads for the ESC’s face the front and rear of the quad. 3

• Firelands X BOLT 250, Option 1 - No LED Bar Install the two M3 35mm alumi- num standos. Install two M3 10mm nylon standos at center of frame. Install four M3 10mm alu- minum standos. All standos are mounted using M3 6mm screws from bottom side of frame Option 2 - LED Bar Install Replace the two nylon 10mm strandos with the 10mm alumi- num standos from the rear of the frame. Install the LED bar at the rear of the frame. Screw the two M3 6mm grub screw (threaded rod) into the 10mm aluminum sta

• Locate the carbon ber camera mount plate and FPV camera. Unscrew the lens from the camera and insert through the hole on the camera mount, rescrewing the lens back onto the camera base. Focusing the camera will be per- formed after the X Bolt is assem- bled. Focus is accomplished by screwing the lens in/out. The lock ring will x the position of the cam

• Firelands X BOLT 250, No HCT mount option Locate the carbon ber top plate. Install four M3 10mm standos as shown in photo to left. Install the standos with M3 6mm screws from the bottom side of frame. Locate the 90 degree header pins. Solder in place to channels 1-4 on the ight controller. These are the 4 speed control connections. NOTE: Double check polarity marked on the ight controller for your ESC’s Satellite Receiver Option Leave yourself 3” of wire to the satellite receiver. Solder the three leads to the ight controller. External Receiver Option Locate the wire loom and header pins as shown in photo to right. Solder header pins to ight con- troller 6

• Firelands X BOLT 250, Discard JST Plug Cut 2-1/2” Long Retain for later step Locate the VTX power wire with the JST plug installed. This wire will need to be modied for two applications in the following steps. Cut the JST plug o close to the connector. Discard the plut. From the remaining wire, cut a section of wire 2-1/2” long. You will use this wire to power the ight con- troller from the PDB later in the manual. The remaining wire with the white plug attached will power the VTX and camera simultaneously. Solder the VTX power leads to the ground and 12V tabs on the PDB as shown in photo to left. Locate the 4” piece of 16 AWG wire and cut in half. Solder one end of each

• Firelands X BOLT 250, Locate the four 18A brushless ESC’s. Solder the ESC power leads to the PDB as shown in the photo to the right. NOTE: Maintain the correct polari- ty as marked on the PDB. Locate four 2206 Brushless mo- tors and hardware. Locate the carbon ber arms and match the holes on the motors to the holes on the arms. If they do not match, ip the arm over. 8

• Firelands X BOLT 250, Using a needle le or sandpaper ease the edges of the hole in the arms to avoid chang the motor wires. Feed the wires through the hole and mount the motor to the arm, using the screws provided with the motors. 9

• Firelands X BOLT 250, Option 1 Expert Solder directly to the ESC. Make 2 slits on the sides of the ESC and fold back the heat shrink to ex- pose the 3 solder pads. NOTE: Use caution when solder- ing next to FETS. Option 2 Intermediate Splice ESC and motor wires together as shown in the photo. Only cut the wires from the ESC, do not cut the motor wires. Cover exposed solder joints with heat shrink (not included). Add top plate and feed the VTX cable through the frame. If you choose to add the optional buzzer it should be installed at this point. In this step we will use the 2-1/2”

• Firelands X BOLT 250, Washers Washers Spacers Thumbscrew Standoff Before you install the top plate you will need to install the motor arms. To complete this step you will need. 8 M3 20mm screws 8 M3 aluminum spacers 24 Nylon washers 4 M3 Thumb screws 4 10mm Nylon standos F/F Arm Assembly Sequence 11

• Firelands X BOLT 250, Install the two M3 23mm standos. These will thread onto the grub screws that you installed earlier. Wrap the VTX with the provided piece of heatshrink. This will pro- vide protection for your VTX. 12

• Firelands X BOLT 250, Plug in all your components. The camera, VTX, satellite receiver and ESC’s. Double check ESC polarity. Diagram shows channel selection for your ESC’s and motor rotation direction. Refer to the diagram to the right. At this point you should have the top and bottom plates assembled. Install M3 nylon hex nuts to secure the ight controller. Fit battery tray over 23mm stand- os. Secure with ve M3 6mm screws. 13

• Firelands X BOLT 250, The HCT plug adapter helps clean up wiring and holds the battery leads in place. Locate two 15mm nylon standos M/F. These are installed on the battery tray as shown in photo to right. These are to protect the battery in the event of a crash. Locate the camera plate and install using four M3 6mm screws. At this point you are ready to set up in Cleanight. 14

• Firelands X BOLT 250, The download and installation of Cleanight is beyond the scope of this assembly manual. Please go to: Cleanight.com for latest software. An addi- tional source of good information is RCGroups.com 30-Day Limited Warranty Term Period: We warranty that the Product(s) purchased (the “Product”) will be free from defects in materials and work manship when the product is new (before being used) for the limited warranty term period, 30 days, from the date of purchase by the Purchaser. If you believe a defect in material, workmanship, etc. was not apparent when the

Related Products and Documents (Quadcopters):

Comparable Devices:

Similar Resources:

• Carrera Video One 370503003 (60 pages) Made in China, ShantouMontage- und Betriebsanleitung Assembly and operating instructions Instructions de montage et d’utilisation Instrucciones de montaje y de servicio Istruzioni per il montaggio e l’uso Montage- en gebruiksaanwijzing Instruções de montagem e modo de utilização Monterings- och bruksanvisning Asennus- ja käyttöohje Instrukcja monta …

• Horizon Hobby BLADE INDUCTRIX BLH8780 (4 pages) ®RTF/BNF Instruction ManualNOTICEAll instructions, warranties and other collateral documents are subject to change at the sole discretion of Horizon Hobby, LLC. For up-to-date product literature, visit horizonhobby.com and click on the support tab for this product. MEANING OF SAFETY SIGNAL WORDSThe following terms are used throughout the product literature …

• Reely Green Racer FPV (164 pages) BedienungsanleitungElektro-Quadrocopter „Green Racer FPV“ RtFBest.-Nr. 1719347 Seite 2 - 42Operating Instructions“Green Racer FPV” RtF electric quadrocopterItem No. 1719347 Page 43 - 82Notice d’emploiQuadricoptère électrique « Green Racer FPV » RtFN° de commande 1719347 Page 83 - 123GebruiksaanwijzingElektrische Quadcopter „Green Racer F …

• TYPHOON Q500 (2 pages) NOTICES AND WARNINGSOVERVIEWTYPHOON Q500+ Quickstart V3.0IMPORTANT NOTE: All safety precauons and warnings, instrucons, warranes and other collateral informaon is subject to change at the sole discreon of Yuneec. For the most up-to-date informaon please visit the corresponding product page at www.Yuneec.com or contact the nearest Yune …

• XK X251 (2 pages) XK X251 adjusting the X7 Transmitter Info collected from: www.rcgroups.com and info shared by SoloProFan & SeByDocKy 3G Mode: Even though this quad is capable of flying in 3G mode, and perform manual flips, the transmitter may not have been setup properly, to access 3G mode. I'll try to list all the steps involved to allow the switch marked &quo …

• dji SPARK (25 pages) Main Screen Connect* your DJI Spark to your iPhone/iPad! Then tap the Picture to start! *you can connect directly to the spark wifi or use the DJI remote (WIFI or OTG connection) Icons in the Main Screen: Map View: • View the last known drone position. User Guide: • Brings you to this user guide. App Information: •Provides you with info …

Comments, Questions and Opinions: