Manualios.com

Carrier 48/50HG014-028 Installation Instructions Manual

  • 48/50HG014-028 Smoke Alarm
  • manvrjfUnLjHo
  • Installation Instructions Manual
  • PDF / Adobe Acrobat Reader
  • 10

Carrier 48/50HG014-028 Manual Online:

3.2, 1884 votes
Carrier 48/50HG014-028 User Manual
Carrier 48/50HG014-028 User Guide
Carrier 48/50HG014-028 Online Manual

Text of Carrier 48/50HG014-028 User Guide:

  • Carrier 48/50HG014-028, 1 48/50HG014---028, 48/50PG20---28 Single---Package Roof top Units with COMFOR T Linkt and Electro---Mechanical Controls Retur n and Supply Sm o ke Detectors Accesso r y Installation Instructions PART NO. CRSM KDET001D00, CRSMKSUP001B00, CRSMKSEN001A00 TABLE OF CONTENTS GENERAL 1........................................ SAFETY CONSIDERATIONS 1........................ INSTALLATION 2................................... Check Package Contents 2........................... Return Air Smoke Detector Installation 2............... Supply Air Smoke Detector Installation 5............... Sensor Installation 7............................... Configuring the ComfortLinkt

  • 2 Understan d the signal words DANGER, WARNING, and CAUTION. These words are used with the safety--alert symbol. DANGER identifies th e most serious hazards which will result in severe personal injury or death. WARNING signifies a hazard which could result in personal injury or death. CAUTION is used to identify unsafe practices which may result in minor personal injury

  • Carrier 48/50HG014-028, 3 Exhaust tube Rubber gasket Cover gasket (ordering option) Sensor housing and electronics Rubber gasket Sensor cover Plug Sampling tube Collar Power Dirty Trouble Alarm LEDs Smoke Sensor Fastener (2X) Controller cover Conduit nuts ( field supplied ) Conduit support plate Cover gasket (ordering option) Conduit couplings Terminal block cover Controller housing and electronics Power Trouble Alarm LEDs ( field supplied ) Smoke Control Module C07173 Fig. 2 --- Smoke Detector SMOKE CONTROL MODULE RETURN SMOKE SENSOR A1B1/A2C1/B1 PLUG LOCATION C07174 Fig. 3 ---

  • Carrier 48/50HG014-028, 4 10. Mount the sampling tube support bracket to the cross member with two 1/4AB-14 5/8-in. screws (P/N AL48AM307) as shown in Fig. 5. Insert large snap bushing (P/N HY93NH085) into hole in bracket. 11. Slide sampling tube into bracket. (See Fig. 4.) Pull the sampling tube so that the locking collar snaps into the smoke detector. 12. Attach smoke detector to partition using two, 8-18 3/4-in. pan head screws (P/N AL56AU168). EQUIPMENT DAMAGE HAZARD Failure to follow this caution may result in equipment damage. Do not overtighten the screws. CAUTION ! 13. Replace the unit side panel. 14. Install the snap bushing (P/N HY93NH069) in the cente

  • Carrier 48/50HG014-028, 5 SAMPLING TUBE SUPPORT BRACKET C07176 Fig. 5 --- Sampling Tube Support Bracket CUT OFF CONNECTOR, LABELED TB3-5, ON ORN WIRE PL19 C07177 Fig. 6 --- Return and Supply Air Smoke Detector Wiring on ComfortLink Units Supply Air Smoke Detector Installation (CRSMKSUP001D00) The supply air smoke detector is to be installed in the predrilled holes located on the front of the first indoor blower. (See Fig. 9.) ELECTRICAL SHOCK HAZARD Failure to follow this warning could result in personal injury and/or death. Prior to installation of this accessory, make sure all power is disconnected to the unit and locked out and tagged. ! WARNING 1. Open the indoor f

  • Carrier 48/50HG014-028, 7 6. Slide the sampling tube collar over the sampling tube until the tabs lock into the tube. 7. Slide sampling tube into smoke detector with eight slots. Make sure sampling tube holes are aligned facing UP. 8. Insert plug into far end of the sampling tube. 9. Place rubber gaskets over each sampling tube on smoke detector. (See Fig. 2.) 10. Remove one knockout from top of smoke detector. 11. Insert one end of RJ-45 wire harness through knockout and wire to smoke detector as shown in Fig. 10. 12. Slide smoke detector into holes in fan side plate with the terminal block at the top and secure using two, 8-18 3 / 4 -in. pa

  • Carrier 48/50HG014-028, 8 SMOKE DETECTOR WIRE TIES C07180 Fig. 9 --- Supply Smoke Detector Location and Wire Routing (Top View) AS SHOWN TO PLUG ROUTE RJ-45 HARNESS ALONG SUPPLY SMOKE DETECTOR THRU BOX, AND OUT SMOKE POWER HARNESS PUNCH OUT KNOCK OUT INSTALL CONTROL MODULE HERE USING THREE SCREWS RJ-45 HARNESS CUT TAPE BEFORE INSERTING SMOKE DETECTOR. C07181 Fig. 10 --- Supply Control Module Installation (Side View) Configuring the ComfortLinkt Controller Configuration settings for the ComfortLink controller are changed by using the Scrolling Marquee dis

  • Carrier 48/50HG014-028, 9 The smoke detector contains a photoelectric detector approved for an extended air speed range of 100 to 4000 feet per minute and an operational temperature range of -4_ to 158_F. Do not operate the smoke detector out of these ranges. The smoke detector operates on 24 vac, 120 vac, or 220/240 vac. The thermostat power terminals on the unit are used to power the smoke detector. The cover of the controller contains the Alarm, Trouble, Dirty and Power LEDs. The cover of the sensor contains the Alarm, Trouble and Power LEDs. (See Fig 2.) The smoke detector can be reset by a momentary power interruption, by the reset button on the front cover

  • 10 To perform a controller alarm test: 1. Press the controller’s test/reset switch for seven seconds. Verify that the controller’s Alarm LED turns on. 2. After performing a controller alarm test, reset the sensor by pressing the test/reset switch for two seconds. Verify that the controller’s Alarm LED turns off. Controller Dirty T est The controller dirty test checks the contr

Related Products and Documents (Smoke Alarm):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 Patton electronics ipRocketLink IAD 3086 Specification sheet patton-electronics/iprocketlink-iad-3086-973.pdf 23 Dec 2022 2 0.17 Mb
2 Mazda Millenia 1996 Workshop manual mazda/millenia-1996-COH.pdf 27 Jul 2023 1252
3 AT&T MERLIN LEGEND Operation & user’s manual at-t/merlin-legend-C1Q.pdf 31 Mar 2023 6 0.04 Mb
4 Weslo Aero A6 Operation & user’s manual weslo/aero-a6-MMY.pdf 04 Sep 2022 12 0.65 Mb
5 Samsung PS51E8000GU Operation & user’s manual samsung/ps51e8000gu-TT4.pdf 30 Jul 2023 46
6 Patton electronics 2003 Operation & user’s manual patton-electronics/2003-72N.pdf 16 Aug 2022 15 0.14 Mb

Similar Resources:

  • Bosch

    FCS‑320‑TP Series

    (84 pages)
    FCS-320-TP seriesConventional aspiration smoke detectorFCS‑320‑TP seriesQuick installation guidedeutschenglishespañolmagyaritalianonederlandspolskiportuguêsрусский …
  • Resolution

    RE614

    (12 pages)
    INSTALLGUIDEIRE614 Smoke Alarm is a fire-protection device that alarms when it detects smoke or temperatures above 135°F (57°C).Features• UL217 and ULC531 listings• Smoke and heat detection• 5 year warrantyQuick Start Guide 1. Remove the mounting plate.2. Pull the battery tab.3. Restore the mounting plate and twist it fully onto the smoke alarm …
  • Firehawk

    FHB10W

    (2 pages)
    Assemble ALL ALARMS as per points 1 & 2 before moving to point 3Note the 10 SECOND WINDOW at point 3.7. If you miss this 10 second window, you will need to reset all alarms and start againIf you have di󰀩culty connecting your alarms, please watch our interlink video guide or contact Safelincs’ customer support team.www.safelincs.co.uk/rehawk-inter …
  • CrossXfire

    CFH10

    (24 pages)
    MADE IN THE U.S.A.SIGNALINGLISTEDModel CFH10Owner’s Manual• Rate of Rise Temperature Sensing• Selectable Fixed Temperature Sensing• Proprietary Wireless ConnectivityHeat Alarm …
  • Perenio

    PECSS01

    (8 pages)
    Doc Date: August 31, 2020 Version: 2.1.1 ©Perenio IoT spol s r.o. All Rights Reserved 1 Dear Customer, thank you for choosing Perenio® products! The Smoke Sensor is generally intended to timely detect smoke and visible particles in the area of installation. It may be used as part of the Perenio Smart Building Management System …
  • Shenzhen

    JTY-GD-930KE

    (2 pages)
    Version:1024151027E-1-Instruction Manual of JTY-GD-930KE Point-type PhotoelectricSmoke Detector------ Please read this Manual carefullybefore installingand usingtheproduct. -----I. Product overviewJTY-GD-930KE point-type photoelectric smoke detector (Detector hereunder) is a two-wireswitch-type smoke-sensing detector. As a non-polar two-wire connection is ad …

Comments, Questions and Opinions: