Allied AT-ARW256E Quick Installation Manual

Text of Allied AT-ARW256E User Guide:

• Allied AT-ARW256E, AT-ARW256E Quick Installation Guide Typical Wireless ADSL Router Connections Up to 4 PCs Connections For More than 4 PCs Connections To connect to more than 4 computers/notebooks, you may further expand one of the Ethernet Ports via an Ethernet Hub/Switch. For details on how to connect to the Ethernet Switch/Hub, please refer to the documentation that comes with the unit. With the Auto MDI/MDIX feature, both cross and straight UTP cable can be utilized. Page 5 of 32

• Allied AT-ARW256E, AT-ARW256E Quick Installation Guide 2.2.3 Installing the USB Device Driver - For Windows ® 2000 i Power on your computer to start Windows. ii Place the Installation CD into your CD-ROM Drive. iii At the following prompt, click Next . iv Select Search for a suitable driver for my device (recommended) option and click Next. v Click CD-ROM drives option and click Next. vi At the next prompt, click Next to proceed installation with the indicated driver. vii You may be prompted with Digital Signature Not Found dialog box during installation.

• AT-ARW256E Quick Installation Guide Chapter 4: Setup Wireless ADSL Router via Utility (For Windows 98 SE/ ME/ 2000/ XP Users ONLY) This chapter is only for Windows User, please use the Wireless ADSL Router Utility Installation CD provided to setup the Wireless ADSL Router Utility 4.1 Install Wireless ADSL Router Self-Installation Utility. i Insert

• Allied AT-ARW256E, AT-ARW256E Quick Installation Guide Wireless ADSL Router Overview Front Indicators 4 6 1 2 3 5 1 POWER Lights up when power is supplied to the Wireless ADSL Router. 2 ETHERNET (E1 ~ E4) Lights up when the Ethernet cable is properly connected from your Wireless ADSL Router to the Ethernet Card. Flickers when the ADSL is transmitting/receiving data. 3 WIREL

• Allied AT-ARW256E, AT-ARW256E Quick Installation Guide iv Select Search for the best driver for your device (Recommended) option and click Next. v Click CD-ROM drives option and click Next. vi Select The updated driver (Recommended) DSL Router USB Remote NDIS Network Device and click Next. vii Click Next to proceed installation with the indicated driver. Depending on your system configurations, you may be prompted for your Windows CD-ROM during installation. At the prompt, replace the Installation CD in your CD- ROM Drive

• Allied AT-ARW256E, AT-ARW256E Quick Installation Guide xvi Your will be prompted to save the router settings. Click “OK” to save. xvii After saving the configuration, Wireless ADSL Router Dialup screen will be prompted as shown below. You can confirm your ISP’s Username and Password, and click on “Connect” for connecting to the Internet. Page 27 of 32

• Allied AT-ARW256E, AT-ARW256E Quick Installation Guide vii Please follow the instructions on how to switch on the power for your Wireless ADSL Router. Click “Next” to continue. viii Please make a choice on how you would like to connect to the Wireless ADSL Router. You may choose Ethernet or USB. Click “Next” to continue. Please refer to the next screen if you have selected “Ethernet”, if you have selected “USB””, please ensure that you’ve installed the driver (refer to xi(b)) Page 22 of 32

• Allied AT-ARW256E, AT-ARW256E Quick Installation Guide 2.2.4 Installing the USB Device Driver - For Windows ® XP i Power on your computer to start Windows. ii Place the Installation CD into your CD-ROM Drive. iii At the following prompt, select Install from a list or specific location (Advanced) option and click Next. iv Click Search removable media option and click Next. v Click Finish to complete the first stage of the USB driver installation. vi Repeat step ii and iii. vii You may be prompted with Hardware Installation dialog box. (This happens when Windows detects your driver as a new version). Click Continue Anyway to proc

• Allied AT-ARW256E, AT-ARW256E Quick Installation Guide Chapter 1: Connecting the Wireless ADSL Router to Your Computer/Notebook Power off your Computer/Notebook or/and any connected devices before connecting to the Wireless ADSL Router! 1.1 Connecting to the Ethernet Connect your computer(s)/notebook(s) to the Wireless ADSL Router as illustrated. The following illustration shows the connection of a single computer. NOT SURE HOW THE ETHERNET PORT LOOKS LIKE? The following are some tips to help you locate your Ethernet Ports

• Allied AT-ARW256E, AT-ARW256E Quick Installation Guide xviii Upon successfully connection, the Dialup application will be minimize and an icon will be created at the right-hand bottom of the task bar. Your home webpage will be launched automatically and the info screen displayed below will minimize automatically. This icon symbolized the Wireless ADSL Router is connected to the Internet This icon symbolized that the Wireless ADSL Router is not connected to the Internet Important: Router Default Setting Firmware version 43.12.1 Protocol PPPoE VPI / VCI 0 / 35 DSL Confi

• Allied AT-ARW256E, AT-ARW256E Quick Installation Guide iii Select the option Obtain an IP address automatically and click OK. Click OK again to close. Ensure that your Wireless ADSL Router is powered on. Restart your system. Proceed to Chapter 3. 2.2 Installing the USB Device Driver 1. Proceed with this section ONLY if your computer/notebook is connected to the USB Port of your Wireless ADSL Router! 2. The following screen shots illustrated serve only as examples. For any dissimilarities, please follow closely the instructions prompted on your Computer/Notebook. 3. For Windows® 98 Second Edition users, you may be prompted for y

• Allied AT-ARW256E, AT-ARW256E Quick Installation Guide 1.2 Connecting to the ADSL Line To connect the Wireless ADSL Router to the ADSL line carried out Chapter 1.2(a). To connect the Wireless ADSL Router to the ADSL line and a Telephone set, carried out Chapter 1.2(b). (a) To connect to the ADSL line (b) To connect to the ADSL line and Telephone Set The POTS Splitter (with built-in Microfilter) is a device that allows you to connect both your Telephone cable and Telephone Set to the same Telephone Wall Socket. The device at the

• AT-ARW256E Quick Installation Guide iii Click the IP Address tab. Click the option Obtain an IP address automatically and click OK to save the settings. Ensure that your Wireless ADSL Router is powered on. Restart your system. Proceed to Chapter 3. 2.1.2 For Windows ® 2000 / Windows ® XP i Windows® 2000: a) From your Windows desktop, right-click on the icon

• Allied AT-ARW256E, AT-ARW256E Quick Installation Guide x Status window will display the processing status of how the Wireless ADSL Router is communicating with the computer via Ethernet or USB. xi Upon success detection of the Wireless ADSL Router, the relevant information will be displayed as the screen below. Click “Next” to continue. Page 24 of 32

• AT-ARW256E Quick Installation Guide Introduction Thank you on your purchase of the 4-Port Combo Ethernet USB Wireless ADSL Router! The Wireless ADSL Router allows you to share high-speed broadband connection with multiple PC using a single device wired or wireless. The 4-Port Combo Ethernet USB Wireless ADSL Router can be connected to any computer/notebook with a 10/100 Bas

• Allied AT-ARW256E, AT-ARW256E Quick Installation Guide Chapter 2: Configuring Your Ethernet Network Card / Installing Your USB Device If your computer/notebook is connected to the Ethernet Port of the Wireless ADSL Router, proceed with chapter 2.1. If your computer/notebook is connected to the USB Port of the Wireless ADSL Router, proceed with chapter 2.2. If you r computers/notebooks are connected to both the Ethernet Port and USB Port of you r Wireless ADSL Router, please proceed with both chapter 2.1 and 2.2! 2.1 Configuring Your Ethernet Network Card 1. Proceed with this section ONLY if your computer/notebook is connected

• Allied AT-ARW256E, 4-Port Combo Ethernet USB Wireless ADSL Router __________________________ __________________________ AT-ARW256E Quick Installation Guide Version 1.0 • Product warranty does not apply to damage caused by lightning, power surges or wrong voltage usage. Contents Introduction ...........................................................……….2 Minimum System Requirements .........................……….2 Wireless ADSL Router Package.......................

• Allied AT-ARW256E, AT-ARW256E Quick Installation Guide Back Panel 4 7 1 2 3 5 6 1 DSL Telephone jack (RJ-11) to connect to your Telephone Wall Socket (DSL line). 2 USB USB jack to connect to your PC’s USB slot. 3 RESET To reset your Wireless ADSL Router to factory default settings. (All cus

• Allied AT-ARW256E, AT-ARW256E Quick Installation Guide xiv You can choose to enable your wireless security option. When enabled you will be able to either manually enter a 26 digit HEX keys or auto-generate the encryption key by clicking on the “Generate” button. Click “Next” to continue. xv You have now completed setting up your Wireless ADSL Router. A summary page as shown will let you review all the settings. Click “Finish” to confirm or “Back” to make changes. Note: You may want to have a reference of the wireless information to configure your wireless client. Click on “Save A s” butt

• AT-ARW256E Quick Installation Guide xi a) Please follow the diagram closely on how to setup the connection from your computer to the Wireless ADSL Router via Ethernet. Click “Next” to continue. b) Please follow the diagram closely on how to setup the connection from your computer to the Wireless ADSL Router via USB. Click “Next” to contin

• Allied AT-ARW256E, AT-ARW256E Quick Installation Guide xii For connecting to the Internet, please enter the username and password, VPI and VCI provided by your ISP. You need to select the protocol. Click “Next” to continue. Please contact your ISP if you are unsure of what to enter. xiii You can enter the SSID or choose to generate a SSID, select country type and wireless channel to configure your wireless settings. Click “Next” to continue. Note: For better security, you may choose to hide the SSID of your

• Allied AT-ARW256E, AT-ARW256E Quick Installation Guide 2.2.2 Installing the USB Device Driver - For Windows ® Me i Power on your computer to start Windows. ii Place the Installation CD into your CD-ROM Drive. iii At the following prompt, select Specify the location of the driver (Advanced) option and click Next. iv Click Removable Media option and click Next . v Click Next again to proceed installation with the indicated driver. vi Click Finish to complete the USB driver installation. vii Restart your system when prompted. Proceed to Chapter 3 Pa

• Allied AT-ARW256E, AT-ARW256E Quick Installation Guide iv You can enter their SSID or let the setup wizard auto-generate a SSID by clicking on “Generate SSID”. You are allowed to select your country standard for wireless LAN in “Country Selection, select a wireless channel and can choose whether to hide the SSID. Click on Next. v You can enable wireless security, auto-generate 128 bit encryption key or define your own key. Click on Next. Page 30 of 32

Related Products and Documents (Network Router):

Comparable Devices:

Similar Resources:

• Telenetics FlashPoll DSP9612FP (2 pages) The Telenetics®FlashPoll™modems aredesigned to optimize communication linkswhere high speed or an unlimited number ofdrops is necessary.▲Dual Mode: 9600/4800 bps and FSK▲Fast train modem equalizer with 23 msec RTS/CTS delay▲DSP design with automatic adaptive equalizer▲Leased-line interface protected withheavy-duty surge protection▲Installs in th …

• Juniper T4000 - (4 pages) 1FACT SHEETProduct Description The Juniper Networks® T4000 Core Router is the next generation of T Series routers, extending Juniper’s proven history of innovation and investment protection. The T4000 system more than doubles the per-slot capacity of existing T1600 systems from 100 Gbps to 240 Gbps—and with only 25% increase in power. A fully loaded T40 …

• Digi TransPort WR11 (2 pages) 1 What’s in the boxConnect hardwareTransPort WR11 Cellular Antenna If any item is missing or damaged, please contact your supplier. Note any damage that may have occurred during shipping and report it to the supplier.Depending on model and configuration, the package will also contain additional cables/antennas as appropriate. 2Power SupplyMounting Ti …

• Canyon CNP-BR1 (5 pages) ENG - 1 4 Port Cable/DSL Broadband Router Article: CNP-BR1 Quick Guide v1.0 Package Contents 1. CANYON CNP-BR1 Main Unit 2. Power Adapter 3. Documentation CD 4. Quick Guide 5. Warranty Card Hardware Overview Getting Started Connecting to Device 1. Make sure that all network devices are powered off, including the device itself, PCs, switche …

• H3C S7500 Series (18 pages) Installation Manual H3C S7500 Series Ethernet Switches Table of Contents i Table of Contents Chapter 4 Hardware Installation ..................................................................................................4-1 4.1 Confirming Installation Preparations.................................................................................. 4-1 4.2 I …

• TP-Link TL-WR841N (2 pages) Connect the Hardware Connect an Ethernet cable from the modem to the WAN port on your router.If your Internet connection is through an Ethernet cable from the wall instead of through a DSL / Cable / Satellite modem, connect the Ethernet cable directly to the router’s WAN port, then follow steps 4 and 5 to complete the hardware connection.ModemPower adapte …

Comments, Questions and Opinions: