Challenger AP10LED Operation & User’s Manual

Text of Challenger AP10LED User Guide:

• Challenger AP10LED, AP10LED Manager Guide 1 Manager Guide This User Guide tells you how to operate your intruder alarm system. To simplify this User Guide we have assumed that the alarm system has been installed by a professional intruder alarm system installer (the installer), and that the system is operated in a “typical” way. Aspects of your system that are not “typical” will be described by your installer. NOTE: If you have any questions about your intruder alarm system, then consult your installer, see cont

• Challenger AP10LED, AP10LED Manager Guide 2 Table of Contents MANAGER GUIDE..............................................................................................................1 INDICATIONS ON THE SYSTEM .......................................................................................1 USING SYSTEM..................................................................................................................1 TABLE OF CONTENTS ..................................................................................

• Challenger AP10LED, AP10LED Manager Guide 3 How to Set the System Full Set When you leave your premises you will need to set (or turn on) the intruder alarm system. Before setting the system you should ensure that the premises have been completely vacated and that all doors and windows are closed. Ensure that pets do not have access to the protected areas as they can cause a false alarm. Par

• Challenger AP10LED, AP10LED Manager Guide 4 How to OMIT a zone(s) If you cannot set the alarm system because a detector is faulty and in constant alarm you may need to omit zones from the alarm system. A zone which has been omitted cannot cause an alarm. Omitted zones will be restored after the system is unset. Before a zone can be omitted it has to be enabled by the engineer as “Setup zone attrs/Omit Allowed” zone. Set the system either Full/Part1 or Part2 (for more infor

• Challenger AP10LED, AP10LED Manager Guide 5 How to UNSET from Alarm and RESET the system You can unset the system in SET and reset it after an alarm, Tamper or PA. The system will be programmed to be reset by the user or engineer. This is dependent on System flags set up. See Engineer mode / Setup System/ Flags 1. e.g. Zone 3 trigger alarm System is in Set mode. Enter User code/Manager code It will stop system in alarm and the LED keypad will hint of a

• AP10LED Manager Guide 6 How to go into Manager Program Mode System work in Day mode Go into Manager Menu. Press 1 = Setup Codes There are 2 user codes can be set by LED Keypad in the system. All are 4-digit and can be set to any number fro

• Challenger AP10LED, AP10LED Manager Guide 7 How to change Manager’s Code This option allows each of the users to be given a code. Under Manager Menu. Press to select Setup User codes. Press to change Manager’s Code. Enter the new Manager’s code (4 digits) Press key to save. If the 4-digit is the same as old, the error tone will be generated. Press key will cancel and return. How to change

• Challenger AP10LED, AP10LED Manager Guide 8 How to delete User Code Under Manager Menu. Press to select Setup User codes. Press to change User 1. Press key to delete user 1 code. Da y PA TAMP 1 2 3 4 5 6 7 8 9 10 Day PA TAMP 1 2 3 4 5 6 7 8 9 10 O IMT 1 1 Day PA TAMP 1 2 3 4 5 6

• Challenger AP10LED, AP10LED Manager Guide 9 2 = View Event Log The event log gives a display of all the events that have taken place. The events are arranged by date and time. Up to 16 events can be stored in the memory. When the log reaches 16 events and another event takes place, the first event drops out. The system is known as FILO (First In Last Out). To view the event log: Press: Jump to oldest event Move one event older Move one event newer Jump to newest event Clear all alarm event After selecting

• Challenger AP10LED, AP10LED Manager Guide 10 3 = How to Authorize engineer access For the engineer to have access to the system the Manager will need to authorize Engineer access to the control panel. Enter Manager program mode. Press Press to authorize Engineer access. The Engineer can access program mode within 3hr hour. Press to leave the current menu. 4 = How to set Chime Zone If a Security Zone is programmed as Chime, you can hear specia

• Challenger AP10LED, AP10LED Manager Guide 11 9 = Test System This function has three parts in Test System: Test output, Walk Test, View Walk Test. How to Test Outputs The test outputs are: 0 = BELL, 1 = Strobe, 2 = Speaker, Under Manager Menu. Press key to Select Test System. Press key to select Bell test. Press key to select Strobe test. Press key to select Speaker test. Press ke

• AP10LED Manager Guide 12 How to enter Walk Test The walk test function allows check each Zone trigger, Zone tamper, Detector Tamper, Control panel tamper, Bell Box tamper, Remote Keypad tamper. if order to verify that they are functioning correctly. A tone is g

• Challenger AP10LED, AP10LED Manager Guide 13 Appendix 2 – Zone - Location & Programming Table Zone No: Location Type i.e. E/E/Alarm/PA Full Set Part Set 1 Part Set 2 1 2 3 4 5 6 7 8 9 10 Exit Time Entry Time Exit Mode Timed, Final Door, Silent Exit, Terminated, Disabled Time FLAG 1 On/ Off Flag 2 On/ Off Be

• AP10LED Manager Guide 14 Errors and Omissions Due to our policy of continuous improvement we reserve the right to change specification without prior notice. Errors and omissions excepted. These instructions have been carefully checked prior to publ

Related Products and Documents (Security System):

Comparable Devices:

Similar Resources:

• Soundstream TARANTULA ARS.1 (20 pages) FCC ID NOTICEThis device complies with Part 15 of the FCC rules. Operation is subject to the following conditions:1. This device may not cause harmful interference, and2. This device must accept any interference received, including interference that may cause undesired operation.CAUTION: Changes or modifications not expressly approved by the part responsibl …

• Siemens FDAI91 (8 pages) A6V10257736_d_--_-- Building Technologies2018-12-20 Control Products and Systems FDAI91 / FDAI92 / FDAI93 / AI330 / DCA1191 / DJZ1193en Alarm indicators, adapter frame, surface-mounted housing, indicator housing incl. washerde Alarmindikatoren, Zusatzrahmen, Aufputzgehäuse, Indikatorgehäuse inkl. Dichtungsringfr Indicateurs d’action, cadres supplémenta …

• EverFocus IP Sidekick (10 pages) Connecting and Power-Up 3rd-Party IP Camera through EverFocus IP Sidekick How-To Document Version 1.0 IP SidekickPoEWi-Fi Copyright © EverFocus Electronics Corp, Release Date: August, 2014 …

• eTIGER S2 (31 pages) S2S2 U20130719V1TL SECUALSecurity Alarm SystemENThanks for purchasing TL SECUAL alarm.FRMerci d’avoir achet l’alarme TL SECUAL.ETIGER EUROPE – Rue de la Loi 25 - 7100 La Louvière – [email protected] - www.etiger.comCopyright © ETIGER EUROPE 2013 …

• Safeline SL6+ (86 pages) www.safeline-group.comSafeLine EuropeIndustrieterrein 1-8 · 3290 Diest · BelgiumTel.: +32 (0)13 664 662 · [email protected]: +32 (0)4 85 89 08 95SafeLine Deutschland GmbHKurzgewannstraße 3 · D-68526 Ladenburg · GermanyTel.: +49 (0) 6203 - 840 60 03 · [email protected] NorwaySolbråveien 49 · 1383 Asker · NorwayTel.: +47 94 14 14 49 · po …

• Lorex L14Q684C (27 pages) IP ENABLED 14” 2 PAGE / 8 CHANNEL COLOR QUAD OBSERVATION SYSTEM WITH 4 NIGHT VISION CAMERASL14Q684C BEFORE OPERATING THIS SYSTEM, PLEASE READ THIS MANUAL THOROUGHLYAND RETAIN IT FOR FUTURE REFERENCEFOR MORE INFORMATIONWWW.LOREXCCTV.COM …

Comments, Questions and Opinions: