Cisco ASR 920 Series Installing Manual

Text of Cisco ASR 920 Series User Guide:

• Cisco ASR 920 Series, 3-33 Cisco ASR 920 Series Aggregation Services Router Hardware Installation Guide OL-32751-01 Chapter 3 Installing the CiscoASR 920 Series Router Connecting a Cisco ASR 920 Series Router to the Network Figure 3-24 shows the USB port connector on the Cisco ASR 920 Series Router. Figure 3-24 Cisco ASR 920 Series Router Flash Token Memory Stick Removing a USB Flash Device To remove and replace a USB flash token memory stick from and into a Cisco ASR 920 Series Router, follow these steps: Step 1 Pull the memory stick from the USB

• Cisco ASR 920 Series, 3-18 Cisco ASR 920 Series Aggregation Services Router Hardware Installation Guide OL-32751-01 Chapter 3 Installing the Cisco ASR 920 Series Router Installing and Removing SFP Modules Figure 3-17 Installing an SFP Module into an SFP Module Slot Caution Do not remove the dust plugs from the fiber-optic SFP module port or the rubber caps from the fiber-optic cable until you are ready to connect the cable. The plugs and caps protect the SFP module ports and cables from contamination and ambient light. Store the dust plugs

• 3-26 Cisco ASR 920 Series Aggregation Services Router Hardware Installation Guide OL-32751-01 Chapter 3 Installing the Cisco ASR 920 Series Router Connecting a Cisco ASR920 Series Router to the Network Note You cannot use the USB port and the EIA port concurrently. When the USB port is used, it takes priority over the EIA port. Step 2 Connect the USB Type A cable to the

• Cisco ASR 920 Series, 3-20 Cisco ASR 920 Series Aggregation Services Router Hardware Installation Guide OL-32751-01 Chapter 3 Installing the Cisco ASR 920 Series Router Connecting to the 10/100/1000 Ports • Set the port speed and duplex parameters on both ends of the connection. Step 1 When connecting to workstations, servers, and routers, connect a straight-through cable to an RJ-45 connector on the front panel.When connecting to routers or repeaters, use a crossover cable. Note You can use the mdix auto interface configuration command in the CLI to enable the automatic medium-dependent interface crossover (

• Cisco ASR 920 Series, 3-15 Cisco ASR 920 Series Aggregation Services Router Hardware Installation Guide OL-32751-01 Chapter 3 Installing the CiscoASR 920 Series Router Installing the DC Power Supply Figure 3-14 Using the DC Power Supply Guard 391893

• Cisco ASR 920 Series, 3-22 Cisco ASR 920 Series Aggregation Services Router Hardware Installation Guide OL-32751-01 Chapter 3 Installing the Cisco ASR 920 Series Router Installing the Chassis Ground Connection Warning Use copper conductors only. Statement 1025 Warning When installing the unit, the ground connection must always be made first and disconnected last. Statement 42 This unit is to be installed in a restrictive access location and must be permanently grounded to a minimum 6-AWG copper ground wire. Perform the following procedure to ground the Cisco

• Cisco ASR 920 Series, 3-31 Cisco ASR 920 Series Aggregation Services Router Hardware Installation Guide OL-32751-01 Chapter 3 Installing the CiscoASR 920 Series Router Connecting a Cisco ASR 920 Series Router to the Network Step 3 Connect the DB-9 end of the console cable to the DB-9 end of the terminal. Step 4 To communicate with the router, start a terminal emulator application, such as Microsoft Windows HyperTerminal. This software should be configured with the following parameters: • 9600 baud • 8 data bits • no parity • 1 stop-bit • no flow control Connecting a Management Ethernet Cable When using the Ethernet Management port in the default mode (speed-auto and duplex-auto) the port oper

• Cisco ASR 920 Series, 3-6 Cisco ASR 920 Series Aggregation Services Router Hardware Installation Guide OL-32751-01 Chapter 3 Installing the Cisco ASR 920 Series Router Installing the Router in a Rack Step 2 Position one of the brackets against the chassis side, and align the screw holes. Step 3 Secure the bracket to the chassis with the screws removed when performing Step 1. The recommended maximum torque is 10 in.-lb. Step 4 Repeat Step 2 and Step 3 for the other bracket. Installing the Router Chassis in the Rack Note Ensure adequate air flow when mounting the router in a rack

• Cisco ASR 920 Series, 3-24 Cisco ASR 920 Series Aggregation Services Router Hardware Installation Guide OL-32751-01 Chapter 3 Installing the Cisco ASR 920 Series Router Installing the Chassis Ground Connection Preventing Power Loss Use the following guidelines to prevent power loss to the router: • To prevent loss of input power, ensure that the total maximum load on each circuit supplying the power supplies is within the current ratings of the wiring and breakers. • In some systems, you can use an UPS to protect against power failures at

• Cisco ASR 920 Series, CHAPTER 3-1 Cisco ASR 920 Series Aggregation Services Router Hardware Installation Guide OL-32751-01 38 Installing the Cisco ASR 920 Series Router This chapter describes how to install the Cisco ASR 920 Series Router and includes the following sections: • “Prerequisites” section on page 3-1 • “Installing the Router in a Rack” section on page 3-1 • “Installing the Chassis Ground Connection” section on page 3-21 • “Connecting a Cisco ASR 920 Series Router to the Network” section on page 3-25 Prerequisites Before installing the Cisco ASR 920 Series Router, it is important to prepare for the

• Cisco ASR 920 Series, 3-25 Cisco ASR 920 Series Aggregation Services Router Hardware Installation Guide OL-32751-01 Chapter 3 Installing the CiscoASR 920 Series Router Connecting a Cisco ASR 920 Series Router to the Network Connecting a Cisco ASR 920 Series Router to the Network The following sections describe how to connect a Cisco ASR 920 Series Router to the network: • Connecting Console Cables, page 3-25 • Connecting a Management Ethernet Cable, page 3-31 • Installing and Removing SFP and SFP+ Modules, page 3-31 • Connecting a USB Flash Device, page 3-32 • Connecting Timing Cables, page 3-33 • Connecting Ethernet Cables, page 3-34 • Connecting Cables to SFP Mo

• 3-17 Cisco ASR 920 Series Aggregation Services Router Hardware Installation Guide OL-32751-01 Chapter 3 Installing the CiscoASR 920 Series Router Installing and Removing SFP Modules Installing SFP Modules Figure 3-16 shows an SFP module that has a bale-clasp latch. Caution We strongly recommend that you do not install or remove fiber-optic SFP modules with cabl

• Cisco ASR 920 Series, 3-12 Cisco ASR 920 Series Aggregation Services Router Hardware Installation Guide OL-32751-01 Chapter 3 Installing the Cisco ASR 920 Series Router Installing the AC Power Cables Mount the router with the front panel as shown in the following figure. Figure 3-10 Mounting the Router on the Wall Caution When mounting the router vertically, ensure that the power supplies are at the top. Installing the AC Power Cables To install the AC power cables in the power supply slots: Step 1 Attach the AC power retainer chord as shown in the figure below. 391667

• Cisco ASR 920 Series, 3-28 Cisco ASR 920 Series Aggregation Services Router Hardware Installation Guide OL-32751-01 Chapter 3 Installing the Cisco ASR 920 Series Router Connecting a Cisco ASR920 Series Router to the Network Connecting to the Console Port Using Mac OS X This procedure describes how to connect a Mac OS X system USB port to the console using the built-in OS X terminal utility. Step 1 Use the Finder to choose Applications > Utilities > Terminal. Step 2 Connect the OS X USB port to the router. Step 3 Enter the following commands to find the OS X USB port number: macbook:user$ cd /dev macbook:user$ ls -ltr /dev/*usb* crw-r

• 3-27 Cisco ASR 920 Series Aggregation Services Router Hardware Installation Guide OL-32751-01 Chapter 3 Installing the CiscoASR 920 Series Router Connecting a Cisco ASR 920 Series Router to the Network Figure 3-22 Connecting the USB Console Cable to the Cisco ASR 920 Series Router Label Cable Label Cable 1 USB Type-A console port 2 USB USB Type-A to USB Ty

• Cisco ASR 920 Series, 3-2 Cisco ASR 920 Series Aggregation Services Router Hardware Installation Guide OL-32751-01 Chapter 3 Installing the Cisco ASR 920 Series Router Installing the Router in a Rack Installing the Chassis Brackets The chassis is shipped with mounting brackets that can be installed on the front or rear of the chassis. To install the brackets on the front of the chassis, perform these steps: Step 1 Remove the rack-mount brackets from the accessory kit and position them beside the router chassis. Figure 3-1 shows how to attach the brackets at the front, middle, and rear positions on the Ci

• Cisco ASR 920 Series, 3-5 Cisco ASR 920 Series Aggregation Services Router Hardware Installation Guide OL-32751-01 Chapter 3 Installing the CiscoASR 920 Series Router Installing the Router in a Rack Figure 3-3 Attaching Mounting Brackets for a 300 mm ETSI Cabinet (Front, Middle, and Rear Positions) 391642 391655

• Cisco ASR 920 Series, 3-30 Cisco ASR 920 Series Aggregation Services Router Hardware Installation Guide OL-32751-01 Chapter 3 Installing the Cisco ASR 920 Series Router Connecting a Cisco ASR920 Series Router to the Network Connecting to the EIA Console Port Note The US-to-RJ45 adapter cable and the DB9 console cable are not included with the Cisco ASR 920 Series Router; they can be ordered separately from Cisco. Note The serial console cable kit is not included with the Cisco ASR 920 Series Router; it is ordered separately. To connect a terminal to the EIA C

• Cisco ASR 920 Series, 3-16 Cisco ASR 920 Series Aggregation Services Router Hardware Installation Guide OL-32751-01 Chapter 3 Installing the Cisco ASR 920 Series Router Installing and Removing SFP Modules Figure 3-15 Attaching the DC Power Supply Step 3 Close the DC power supply guard. Powering On the Router After the router is either rack mounted or mounted on the wall, perform these tasks to complete the installation: • Power on the router. • Connect the front-panel ports. See the Connecting to SFP Modules, page 3-20 to complete the installation. Installing and Removing SFP Modules These s

• Cisco ASR 920 Series, 3-9 Cisco ASR 920 Series Aggregation Services Router Hardware Installation Guide OL-32751-01 Chapter 3 Installing the CiscoASR 920 Series Router Wall Mounting the Cisco ASR 920 Series Router Figure 3-7 Installing the Cable Guides (As Per the Standard Kit) Wall Mounting the Cisco ASR 920 Series Router To install the Cisco ASR 920 Series Router on a wall, follow the instructions in these procedures: • Attaching the Brackets to the Router for Wall-Mounting, page 3-9 • Mounting Cisco ASR 920 Series Router on the Wall, page 3-10 Attaching th

• Cisco ASR 920 Series, 3-8 Cisco ASR 920 Series Aggregation Services Router Hardware Installation Guide OL-32751-01 Chapter 3 Installing the Cisco ASR 920 Series Router Installing the Router in a Rack To install the cable guides, perform these steps: Step 1 Position the cable guide-left and cable guide-right against the front of the chassis and align the four screw holes, as shown in Figure 3-5. Figure 3-5 Cable Guide Installation For 19-inch Rack Brackets Figure 3-6 Cable Guide Installation For ETSI Rack Brackets Step 2 Secure the cable guides with the four M6x12mm screws supplied with the cable kit. The recommended

• Cisco ASR 920 Series, 3-7 Cisco ASR 920 Series Aggregation Services Router Hardware Installation Guide OL-32751-01 Chapter 3 Installing the CiscoASR 920 Series Router Installing the Router in a Rack Figure 3-4 Installing the Chassis in a 19-inch EIA Rack Step 3 Install the four M6x12mm zinc-plated steel screws through the holes in the bracket and into the threaded holes in the equipment rack posts. Step 4 Use a tape measure and level to verify that the chassis is installed straight and level. Attaching the Cable Guides The Cisco ASR 920 Series Route

More Instructions:

	Cisco ASR 920 Series Configuration 13-10-2023 52	DOWNLOAD
	Cisco ASR 920 Series Configuration manual 20-01-2023 78	DOWNLOAD
	Cisco ASR 920 Series Installing manual 25-02-2024 42	DOWNLOAD
	Cisco ASR 920 Series Configuration manual 26-07-2022 68	DOWNLOAD

Related Products and Documents (Network Router):

Comparable Devices:

Similar Resources:

• ZyXEL Communications NBG-4615 (56 pages) www.zyxel.comNBG4615Wireless N Gigabit NetUSB Router Firmware Version 1.00Edition 1, 12/2010DEFAULT LOGIN DETAILSLAN Port LAN1 ~ LAN4IP Address http://192.168.1.1Password 1234CONTENTSENGLISH 3DEUTSCH 9ESPAÑOL 15FRANÇAIS 21ITALIANO 27SVENSKA 35NEDERLANDS 41繁體中文 47 2010 ZyXEL Communications CorporationC …

• Cisco Router Cisco 3600 (24 pages) 1Doc. No.Cisco Systems, Inc.All rights reserved.170 West Tasman DriveSan Jose, CA 95134-1706USACisco Systems, Inc.Corporate HeadquartersCopyright © 1996Cisco 3600 Series Memory UpgradeConfiguration NoteProduct Numbers:MEM3600-4FS=, MEM3600-8FS=, MEM3620-4D=, MEM3620-8D=, MEM3620-16D=,MEM3640-4D=, MEM3640-8D=, MEM3640-16D=, MEM3640-32D=CPAMEM3600-4FS=, CPA …

• IBM GX4004 (3 pages) Copyright© 2007 IBM Internet Security Systems. All rights reserved worldwide. Internet Security Systems is a trademark, and Proventia is a registered trademark of IBM Internet Security Systems. All other marks and trade names mentioned are the property of their owners, as indicated. All marks are the property of their respective …

• AMC XO (20 pages) IAPOWERH.O.M.E. AUTOMATION SERIESXODigital Home system15263748AMCXO8 ZONE 8 SOURCE DIGITAL H.O.M.E. SYSTEMwith Remote Local Sources&Instant Installing All Zone Connectors …

• D-Link D EBR-2310 EBR-2310 (2 pages) CREATE A WIRED NETWORKETHERNET BROADBAND ROUTERSHARE THE INTERNET Easily create a basic network to share your Internet connectionBASIC NETWORKINGCreate a wired network in your home using the D-Link Ethernet Broadband Router (EBR-2310). Connect this Wired Router to a broadband modem and share your high-speed Internet access, check email, share les, and en …

• Proroute H820 (2 pages) PROROUTEH820 / H685QUICK START GUIDE PROROUTE H820 / H685 QUICK START Thank you for your purchase. We have included in this quick start guide the basics of getting your router connected to the Internet and configure basic services. For full installation instructions and help guides and videos please visit the support section at www.proroute.co.uk.PRODUCT …

Comments, Questions and Opinions: