Cisco Catalyst 3920 Installation Manual
|
Cisco Catalyst 3920, CHAPTER Installing the Catalyst 3920 3-1 3 Installing the Catalyst 3920 This chapter explains the process you should follow to install the Catalyst 3920 Token Ring Switch. Planning for Installation Read this section carefully before installing the Catalyst 3920 Token Ring Switch. It contains the information on preinstallation planning. Note Before installing the Catalyst 3920, read the “Safety Warnings” appendix. Warning Read the installation instructions before you connect the system to its power source. If you have a large network, we recommend that you create a sketch of the network to
Cisco Catalyst 3920, Installation Summary Catalyst 3920 Token Ring Switch User Guide 3-2 Dedicated Media For installations where permanently installed building cable is available, 100-ohm UTP Category 3, 4, or 5 can be used. IBM Cabling System 150-ohm, STP cables (types 1 and 9) can also be used. Because the RJ-45 connectors on the Catalyst 3920 use pins 3, 4, 5, and 6, a cable with an IBM STP data connector on one end and an RJ-45 connector on the other must be constructed. Shared Media The types of cables that can be used are the same as tho
Cisco Catalyst 3920, Installing the Catalyst 3920 3-3 Gathering Other Materials You Will Need To install the Catalyst 3920, you need the following items: • If the unit will be installed in a rack, you need: — Rack inventory chart and a cabling chart from your network administrator. — Four screws appropriate for your rack and a screwdriver. (Make sure that you have the appropriate screws before you begin installation.) • If the unit will be installed as standalone equipment (such as on a tabletop), you will need: — Cabling chart from your network administrator. Setting Up the Cataly
Cisco Catalyst 3920, Setting Up the Catalyst 3920 Catalyst 3920 Token Ring Switch User Guide 3-4 Figure 3-1 Attaching the Mounting Brackets Step 4 Position the Catalyst 3920 in the rack or cabinet and slide it up or down until the rack holes line up with the bracket holes. Attach the Catalyst 3920 to the rack with the appropriate mounting screws (see Figure 3-2). Figure 3-2 Mounting in a Rack or Cabinet Step 5 Go to the instructions in the “Cabling the Catalyst 3920” section. Warning To prevent the switch from overheating, do not operate it in an area that exceeds the maximum recommended ambient temperature of 104 F(40 C).To prevent airflow restriction, allow at least 3 inches (7.6 cm) of clearance around
Cisco Catalyst 3920, Installing the Catalyst 3920 3-5 Surface Mounting the Catalyst 3920 Follow these steps to mount the Catalyst 3920 as a standalone unit: Step 1 Obtain the chassis feet from the accessory kit. Step 2 Remove the protective paper from the adhesive surface of the feet and place the four feet in each of the four embossed, recessed areas located in the corners of the bottom of the Catalyst 3920. Step 3 Place the Catalyst 3920 on the surface where it is to be used. Step 4 Continue with the instructions in the “Cabling the Catalyst 3920” section. Cabling the Catalyst 3920 This section provides instru
Cabling a Catalyst Stack Configuration Catalyst 3920 Token Ring Switch User Guide 3-6 Step 4 Label this cable. Step 5 Continue with the instructions in the “Powering On the Catalyst 3920” section. Cabling a Catalyst Stack Configuration As an option, you can configure your Catalyst 3920 as a part of a Catalyst stack. There are two Catalyst stack configurations. • Two Catalyst 3920 switc
Cisco Catalyst 3920, Installing the Catalyst 3920 3-7 Figure 3-4 Connecting the Stack Port Cable to the Stack Port Figure 3-5 Connecting the Other End of the Cable to the Other Catalyst 3920 Connecting Catalyst Switches to the Catalyst Matrix Up to eight Catalyst switches can be connected to a Catalyst Matrix. This configuration requires a Catalyst Matrix, and a stack port cable. The connection is made through one of the eight I/O stack ports on the back panel of the Catalyst Matrix to the single I/O stack port on the stack po
Powering On the Catalyst 3920 Catalyst 3920 Token Ring Switch User Guide 3-8 Figure 3-6 Connecting the Stack Port Cable to Port 1 of the Catalyst Matrix Step 2 Attach the other end of the cable to the stack port of a Catalyst switch (Figure 3-7). Repeat these steps for each Catalyst switch using the next lowest numbered port on the Catalyst Matrix. Figure 3-7
Cisco Catalyst 3920, Installing the Catalyst 3920 3-9 Caution If a fully-redundant configuration is used, do not connect the AC power cord to the Catalyst 3920 as this may cause damage to the Catalyst 3920 or the RPS. Step 3 Verify that the power (PWR) LED on the left side of the front panel is on. If it is not, make sure that the outlet is working correctly. If the outlet is working but the PWR LED is off, contact your Cisco Systems representative. Step 4 Verify that diagnostics have been completed successfully. The Catalyst 3920 automatically performs a self-test when connected to a power supply. During the test, the LEDs should behave as follows: • In the first 2 minutes, the Mode LED is on and the FL
Cisco WS-C5008B - Power Supply - 1100 Watt Switch Installation manual
WS-C5008B - Power Supply - 1100 Watt |
Cisco SRW248G4P Switch Datasheet
SRW248G4P |
Cisco AJ732A - MDS 9134 Fabric Switch Switch Configuration manual
AJ732A - MDS 9134 Fabric Switch |
Cisco AJ732A - MDS 9134 Fabric Switch Switch Release note
AJ732A - MDS 9134 Fabric Switch |
Cisco 8600 Switch Dimensions
8600 |
Cisco 8800 Switch Hardware installation manual
8800 |
Cisco AJ732A - MDS 9134 Fabric Switch Switch Installation manual
AJ732A - MDS 9134 Fabric Switch |
Cisco Catalyst 4500 Series Switch Installation manual
Catalyst 4500 Series |
# | Manufacturer | Model | Document Type | File | Updated | Pages | Size |
---|---|---|---|---|---|---|---|
1 | Hunter | Cornelius 59514 | Owner's manual and installation manual | hunter/cornelius-59514-Z45.pdf | 03 Feb 2024 | 2 | |
2 | Sunbeam | 3224 | Operation & user’s manual | sunbeam/3224-Z6P.pdf | 20 Mar 2024 | 24 | |
3 | Soundstream | Picasso | Owners and installation manual | soundstream/picasso-HM3.pdf | 22 Nov 2022 | 10 | 0.96 Mb |
4 | Cooper Lighting | Interior Wall Luminaire 673 | Specification sheet | cooper-lighting/interior-wall-luminaire-673-6SQ.pdf | 03 Oct 2023 | 1 | 0.05 Mb |
5 | Atlona | AT-RGB110 | Operation & user’s manual | atlona/at-rgb110-3JH.pdf | 11 Jul 2022 | 8 | 0.81 Mb |
6 | Sony | M-335 | Operating instructions | sony/m-335-2O4.pdf | 02 Aug 2023 | 2 | 0.27 Mb |
Dell
FILE LOCATION: C:\Users\gina\Desktop\Checkout_new\CLI Folders\Dell Contax CLI\files\New Cover_Dell_Contax.fmDELL CONFIDENTIAL – PRELIMINARY 5/15/12 – FOR PROOF ONLYTemplate Last Updated -03/06/2010Dell PowerConnect 5500SeriesCLI Reference GuideRegulatory Model: PC5524, PC5524P, PC5548 and PC5548P
…
PowerConnect PC5524(763 pages) |
Repotec
8 Ports PoE Gigabit LAN Switch IEEE 802.3at/af User’s Manual FCC Warning This device has been tested and found to comply with limits for a Class A digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial …
RP-PEG08-H(2 pages) |
iNels
02-46/2015 Rev.1RFJA-12B/230V, RFJA-12B/24VDCSwitch unit for shuttersENL NL NPEM+-- +M12-24V DCRFJA-12B/230V RFJA-12B/12VDC1/4☺☺☺☺☺RFRP-20Characteristics /• The switching unit for blinds has 2 output channels used to control garage doors, gates, blinds, awnings, etc.• It can be combined with Control or Syste …
RFJA-12B(4 pages) |
F&S
PoE+ Series Switches STP Optional Characteristic Configuration GuideModels: S3150-8T2FP S3260-8T2FP S3260-16T4FP S3400-24T4FP S3400-48T4SP
…
STP Series(15 pages) |
NTI
RACKMUX-4K17-N Rackmount Drawer with 4K Video LCD Monitor, USB Keyboard, and Mouse Installation and Operation Manual MAN338 Rev Date 1/8/2020 RACKMUX® Series RACKMUX-4K17-N (Front View)
…
RACKMUX Series(23 pages) |
MBright Tools iVAC Inc
REMOTE USER GUIDEwww. switch.comMBright Tools iVAC Inc.5570 Jill Street . Box 557 . Osgoode, Ontario Canada . K0A 2W0Tel: 613 826 2200 . Fax: 613 826 3300 . [email protected]
…
iVAC Pro(36 pages) |
Yamaha Offroad Vehicle RX10HPDF User Guide (@CHM669), Yamaha RX10H Offroad Vehicle (17/11/2023) RX10H, 100 |
Speco Security Camera VIP2D1MSpeco VIP2D1M Security Camera Instruction manual VIP2D1M, 73 |
Onkyo Amplifier R-801AOnkyo Product Manual: R-801A PDF Service manual - F8NYPT R-801A, 32 |
Polaroid Digital Camera A550Polaroid A550 User Guide (Doc Type: Digital Camera Operation & user’s manual) A550, 82 |
Sennheiser Headphone CX 880PDF User Manual (@DHUDQL), Sennheiser CX 880 Headphone (21.11.2023) CX 880, 2 |
Helion Toy HLNA0053PDF User Manual (@M9314N), Helion HLNA0053 Toy (29.01.2024) HLNA0053, 28 |
Aube Technologies Temperature Controller Temperature Sensor AC146-410Installation manual for Aube Technologies Temperature Sensor AC146-410 Temperature Controller Temperature Sensor AC146-410, 2 |
Motorola Modem SURFBOARD CABLE MODEM SB5101 - WARRANTYPDF User Guide (@F32942), Motorola SURFBOARD CABLE MODEM SB5101 - WARRANTY Modem (18.02.2024) SURFBOARD CABLE MODEM SB5101 - WARRANTY, 4 |
Azio Enclosure E233U3Azio E233U3 User Guide (Operation & user’s manual), @AV5YL7 E233U3, 7 |
InFocus Projector LP240Projector #9DVVZ8 LP240, 2 |
Schlage Card Reader WPR400WPR400 Instructions manual - 98ZU9N WPR400, 16 |
Radient Battery Charger Reflex 2-3s LiPoPDF User Guide (@837W2V), Radient Reflex 2-3s LiPo Battery Charger (Thu 11.2023) Reflex 2-3s LiPo, 8 |