Manualios.com

Cisco SCH-CONTROL-200 Reference Manual

Cisco SCH-CONTROL-200 Manual Online:

3.15, 2668 votes
Cisco SCH-CONTROL-200 User Manual
Cisco SCH-CONTROL-200 User Guide
Cisco SCH-CONTROL-200 Online Manual

Text of Cisco SCH-CONTROL-200 User Guide:

  • Cisco SCH-CONTROL-200, Americas Headquarters: Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA Cisco Smart+Connected Controller 200 Reference Guide This document provides information about the available ports, technical specifications and features of the Cisco Smart+Connected Controller 200 (SCH-CONTROL-200). • Overview, page 2 • Package Contents, page 2 • Mounting the Cisco Controller 200 on a Wall, page 3 • Front View (LEDs and Other Features), page 5 • Rear View (Input and Output Ports), page 6 • Connecting Devices, page 6

  • Cisco SCH-CONTROL-200, 2 Cisco Smart+Connected Controller 200 Reference Guide OL-27357-01 Overview Overview The Cisco Smart+Connected Controller 200 provides intelligent control for the Cisco Smart+Connected Residential Solution, allowing residents to manage lighting, security, temperature, and multimedia, while also providing a portal into the community from the residence. The Cisco Controller 200 integrates a broad range of devices using a variety of protocols (Internet Protocol [IP], ZigBee HA, infrared [IR], serial, and more). By combining wired and wireless technologies, the Cisco Co

  • Cisco SCH-CONTROL-200, 3 Cisco Smart+Connected Controller 200 Reference Guide OL-27357-01 Mounting the Cisco Controller 200 on a Wall Note This document, and other related documents, are available online at www.cisco.com/go/smartconnectedresidential/docs. See the “Related Documentation” section on page 11 for more information. Mounting the Cisco Controller 200 on a Wall The Cisco Controller 200 can be mounted on a wall or placed on a horizontal surface (such as a shelf). Procedure To mount the device on a wall: Step 1 Select one of the following mounting options: • Mount the Controller 2

  • Cisco SCH-CONTROL-200, 4 Cisco Smart+Connected Controller 200 Reference Guide OL-27357-01 Mounting the Cisco Controller 200 on a Wall Figure 2 Mounting the Cisco Controller 200 Step 2 Use the four (4) screws (provided) to attach the mounting plate to the bottom of the Controller 200. Ensure that the narrow end of the slots will be on top when the device is installed. Step 3 Arrange the wires to fit in the wire channels on the mounting plate. Step 4 Line the slots on the mounting plate up with the screws. Step 5 Press the device onto the screws and slide down until the

  • Cisco SCH-CONTROL-200, 5 Cisco Smart+Connected Controller 200 Reference Guide OL-27357-01 Front View (LEDs and Other Features) Front View (LEDs and Other Features) Figure 3 Front View 1 IR Window / IR Blaster—For capturing third-party IR codes from hand-held devices (such as remote controls) or blasting IR codes. The Wi-Fi LED blinks red when capturing IR codes. 2 Wi-Fi LED—The Wi-Fi LED blinks orange and then blue during the boot process. When the operating system is running, the Wi-Fi driver changes the LED color depending on the signal strength of its connection to its associated access point. Colors and signal strength are: • orange=fair to good • blue=

  • Cisco SCH-CONTROL-200, 6 Cisco Smart+Connected Controller 200 Reference Guide OL-27357-01 Rear View (Input and Output Ports) Rear View (Input and Output Ports) Figure 4 Rear View Connecting Devices Note Use the Composer Pro software to step through the connection process before or after the physical connections are completed. See the Cisco Smart+Connected Residential Installation and Configuration Guide for more information. Connect all applicable devices to the Controller 200 using the connection options described in the following table. 1 Audio In (1)—3.5 mm jacks for stereo channel input (line level) for one stereo analog source. 2 Audio Out (1 left-right pair)—RCA jack

  • Cisco SCH-CONTROL-200, 7 Cisco Smart+Connected Controller 200 Reference Guide OL-27357-01 Connecting Devices Video Out Options Composite or component ports for displaying navigation menus on a monitor or TV. Use the component jack to display either standard or high-definition video. Use the composite port to display standard definition video. Note The default video output mode is NTSC over composite. In this mode, some bleed-through of the NTSC signal on the component video output connections occurs. However, the video image will not appear correctly in this mode. T

  • Cisco SCH-CONTROL-200, 8 Cisco Smart+Connected Controller 200 Reference Guide OL-27357-01 Connecting the IR Ports/Serial Ports (Optional) Connecting the IR Ports/Serial Ports (Optional) The Cisco Controller 200 provides 4 IR ports. Ports 1 and 2 can be reconfigured for serial communication to connect serial devices such as a receiver or disc changer. A special cable is required (not included). Any jack not used for serial can be used for IR. Serial ports support many different baud rates. The following table shows the

  • Cisco SCH-CONTROL-200, 9 Cisco Smart+Connected Controller 200 Reference Guide OL-27357-01 Setting Up External Storage Device (Optional) Setting Up External Storage Device (Optional) To store and access media from an external storage device, such as a network hard drive or USB memory device, attach the USB drive to the Cisco Controller USB port and configure or scan the media from Composer Pro. See the Cisco Smart+Connected Residential Installation and Configuration Guide for more information. Configuring the Cisco Controller 200 After you install and connect the hardware (such as a touchscreen, TV, lights, etc.), use the Composer Pro software to configure the devices and customize the system. See th

  • Cisco SCH-CONTROL-200, 10 Cisco Smart+Connected Controller 200 Reference Guide OL-27357-01 Regulatory/Safety Information Regulatory/Safety Information To review regulatory information, go to www.cisco.com/go/smartconnectedresidential/docs. Specifications Table 3 Cisco Controller 200 Specifications Basic Specifications Description Audio/Video Inputs and Outputs HDMI out (Digital audio and on-screen navigator) N/A Component video out 1 (720p Only) Composite video out 1 (480i) Analog audio out 1 (L/R RCA) Analog audio input to convert to digital 1 (3.5 mm connector) Digital audio out: Coax (RCA) N/A Total number of audio outputs 1 Network Ethernet ports × speed 1 × 10/100 Zig

  • 11 Cisco Smart+Connected Controller 200 Reference Guide OL-27357-01 Related Documentation Related Documentation For more information about the Cisco Smart+Connected Residential products, see the following documents and websites: www.cisco.com/go/smartconnectedresidential Cisco 1-Year Limited Hardware Warranty Terms www.cisco.com/go/smartconnectedresidential warranty www.cisco.

  • 12 Cisco Smart+Connected Controller 200 Reference Guide OL-27357-01 Warranty Warranty A Cisco 1-year warranty applies. Go to the following URL for more information: www.cisco.com/go/smartconnectedresidentialwarranty Service and Support Cisco offers a wide range of support programs to accelerate customer success. These innovative programs are delivered through a uniq

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 Metra Electronics 95-7321 Installation instructions manual metra-electronics/95-7321-R4T.pdf 18 Jul 2022 8
2 Vizio VF551XVT1A Operation & user’s manual vizio/vf551xvt1a-68E.pdf 25 Mar 2024 76 4.31 Mb
3 Porter-Cable CMB15-B3 Instruction manual porter-cable/cmb15-b3-Z87.pdf 16 Oct 2023 40
4 SignaMax 065-7734 Operation & user’s manual signamax/065-7734-8M9.pdf 19 Feb 2023 175
5 Uniden 900 MHz Owner's manual uniden/900-mhz-6HK.pdf 31 Aug 2022 12 1.09 Mb
6 Naturela NHC-H41 Operation & user’s manual naturela/nhc-h41-QK4.pdf 05 Mar 2023 15

Similar Resources:

  • Siemens

    SINUMERIK 802D sl

    (212 pages)
    Valid forControl Software versionSINUMERIK 802D sl 106/2006 EditionSINUMERIK 802D slOperation and ProgrammingNibblingIntroduction 1Turning On, Reference Point Approach2Setup 3Manually Controlled Mode 4AUTOMATIC Mode 5Part Programming 6System 7Programming 8 …
  • Chore-Time

    PDS

    (38 pages)
    Pneumatic Drinking System (PDS) ControlInstallation and Operators Manual4-32 StationChore-Tronics® 3 PDS™(Part No. 56039-X)PDS™ 4 & 8 Station(Part No. 52430-X)12-40 Station PDS™(Part No.54373-X)MW2467BFebruary 2020 …
  • JEAN LUTZ

    TARALOG

    (158 pages)
    Version TG2TCT231FR Version TG2TCT231EN Fr En DUC 2 rue du Forbeth – 64110 JURANÇON – FranceTél. (33) 05 59 06 34 22 – Fax (33) 05 59 06 15 99 – [email protected] – www.jeanlutzsa.fr __________ TG2TCT231DUCFrEn.doc Français/English …
  • Rowe

    HASCP

    (79 pages)
    1 HASCP Horizontal acoustic sediment & current profiler OPERATION MANUAL H A S C P Rowe Technologies Inc. 12655 Danielson Court, Suite 306 Poway, CA 92064 USA Tel: +1 858 842 3020 Fax: +1 858 842 3021 …
  • Cisco

    SCH-CONTROL-200

    (12 pages)
    Americas Headquarters:Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USACisco Smart+Connected Controller 200 Reference GuideThis document provides information about the available ports, technical specifications and features of the Cisco Smart+Connected Controller 200 (SCH-CONTROL-200). • Overview, page 2 • Package Contents, page …
  • Siemens

    Albatros2 RVS46

    (26 pages)
    Edition 1.0 Controller series A CE1U2353en01a 22. November 2006 Building TechnologiesHVAC Products Albatros2 Zone controler User Manual OEM RVS46..AVS75..AVS37..QAA75..QAA78..QAA55.. …

Comments, Questions and Opinions: