Cisco RV132W Administration Manual

Text of Cisco RV132W User Guide:

• Cisco RV132W, Networking Configuring LAN Settings Cisco RV132W ADSL2+ Wireless-N and RV134W VDSL2 Wireless-AC VPN Router Administration Guide 20 3 In the IPv6 Settings section for both the ATM and PTM (RV134W) transfer modes, enter the following information: For IPv6 For 6rd Static DNS 1 & 2 Enter the IP address of the primary and or secondary Static DNS in the fields (Hint 1.2.3.4). Mode IPv6 Address Mode Select Dynamic or Static. If you select Dynamic, it means that if the RA (Router Advertisement) message that the device rece

• Cisco RV132W, Networking Configuring LAN Settings Cisco RV132W ADSL2+ Wireless-N and RV134W VDSL2 Wireless-AC VPN Router Administration Guide 51 3 STEP 4 In the Failover Check Interval field, enter the frequency (in seconds) with which the device must attempt to detect the physical connection or presence of traffic on the mobile network link. If the link is idle, the device attempts to ping a destination at this interval. If there is no reply to the ping packet, the device assumes the link is down and retries the Ethernet WAN interface. STEP 5 In the Recovery Check Interval field, enter the frequency (in seconds) with which the device must attempt to

• Cisco RV132W, Firewall Services Management Configuration Cisco RV132W ADSL2+ Wireless-N and RV134W VDSL2 Wireless-AC VPN Router Administration Guide 91 5 The Services Management page allows you to create custom services against which firewall rules can be defined. Once defined, the new service appears in the List of Available Custom Services table. To create a custom service: STEP 1 Select Firewall > Service Management. STEP 2 Click Add Row. STEP 3 In the Service Name field, enter the service name for identification and management purposes. STEP 4 In the Protocol field, select the Layer 4 protocol that the service uses from the drop-down list: - TCP - UDP - TCP & UDP - ICMP - ICMPv6

• Cisco RV132W, Networking Configuring LAN Settings Cisco RV132W ADSL2+ Wireless-N and RV134W VDSL2 Wireless-AC VPN Router Administration Guide 65 3 STEP 4 Click Save. To edit the settings of a route, select the route and click Edit. To delete a selected route, click Delete. Click Save to apply changes. Configuring Routing (RIPng) RIP Next Generation (RIPng) is a routing protocol based on the distance vector (D-V) algorithm. RIPng uses UDP packets to exchange routing information through port 521. RIPng uses a hop count to measure the distance t

• Cisco RV132W, Networking Configuring LAN Settings Cisco RV132W ADSL2+ Wireless-N and RV134W VDSL2 Wireless-AC VPN Router Administration Guide 43 3 VLAN & VLAN ID If enabled, all outbound traffic through this interface is tagged with the configured VLAN ID. 802.1p Priority Enter a range from 0 to 7. All outbound traffic of this interface will be tagged with the configured 802.1p priority. If it conflicts with the QoS setting, the QoS setting will take precedence. MTU (Maximum Transmission Unit) MTU is an advanced configuration that allows you to determ

• Cisco RV132W, Networking Configuring LAN Settings Cisco RV132W ADSL2+ Wireless-N and RV134W VDSL2 Wireless-AC VPN Router Administration Guide 26 3 In the IPv6 Settings section for both the ATM and PTM (RV134W) transfer modes, enter the following information: For IPv6 Connect on Demand Max Idle Time Select this option if your ISP charges when you are connected to the Internet. If you select this option, the Internet connection is on - only when traffic is present. If the connection is idle - no traffic is flowing - the connection is closed. If you Connect on Demand, enter the number of minutes after which the connection shuts off in the Max Idle Time field.

• Wireless Networks Configuring Advanced Wireless Settings Cisco RV132W ADSL2+ Wireless-N and RV134W VDSL2 Wireless-AC VPN Router Administration Guide 82 4 CTS Protection Mode The device automatically uses CTS (Clear-To-Send) Protection Mode when your Wireless-N and Wireless-G devices are experiencing severe problems and are not able to transmit to the devi

• Cisco RV132W, Firewall Internet Access Policy Configuration Cisco RV132W ADSL2+ Wireless-N and RV134W VDSL2 Wireless-AC VPN Router Administration Guide 96 5 STEP 5 From the Action drop-down list, select the type of access restriction you need: • Always block—Always block Internet traffic. This blocks Internet traffic to and from all endpoints. If you want to block all traffic but allow certain endpoints to receive Internet traffic, see Step 7. • Always allow—Always allow Internet traffic. You can refine this to block specified endpoints from Internet traffic; see Step 7. You can also allow all Internet traffic except for certain websites; see Step 8. • Block by schedule—Blocks Intern

• Cisco RV132W, Administration Firmware Upgrade Cisco RV132W ADSL2+ Wireless-N and RV134W VDSL2 Wireless-AC VPN Router Administration Guide 138 8 The router allows you to generate an encryption key to protect the backup files. To generate an encryption key: STEP 1 Select Administration > Download/Backup Configuration File. STEP 2 Click Show Advanced Settings. STEP 3 In the box, enter the seed phrase used to generate the key. STEP 4 Click Save. Firmware Upgrade You can upgrade to a newer version of the firmware for the router by using the Administration > Firmware Upgrade page. ! CAUTION During a firmware upgrade, do not try to go o

• Cisco RV132W, Cisco RV132W ADSL2+ Wireless-N and RV134W VDSL2 Wireless-AC VPN Router Administration Guide Contents Configuring Routing 59 Configuring Basic Routing 59 Configuring Dynamic Routing Information Protocol (RIP) 59 Viewing the Routing Table 61 Configuring Dynamic DNS 61 Configuring the IP Mode 62 Configuring IPv6 63 Configuring IPv6 LAN Connections 63 Configuring IPv6 Static Routing 65 Configuring Routing (RIPng) 66 Configuring Router Advertisement 67 Configuring Advertisement Prefixes 68 Chapter 4: Wireless Networks 70 Wireless Security 70 Basic Wireless Settings 72 Configuring Advanced Wireless Settings 80 Configuring WPS 83 Chapter 5: Firewall 85 Basic Firewall Settings 86 Schedule Man

• Cisco RV132W, Firewall Attack Protection Configuration Cisco RV132W ADSL2+ Wireless-N and RV134W VDSL2 Wireless-AC VPN Router Administration Guide 100 5 To add a port triggering rule: STEP 1 Select Firewall > Port Range Triggering. STEP 2 In the Application field, enter the name of the application for which to configure port forwarding. STEP 3 In the Triggered Range fields, enter the port number or range of port numbers that will trigger this rule when a connection request from outgoing traffic is made. If the outgoing connection uses only one port, enter the same port number in both fields. STEP 4 In the Forwarded Range fields, enter the port number or range of port

• Cisco RV132W, Networking Configuring LAN Settings Cisco RV132W ADSL2+ Wireless-N and RV134W VDSL2 Wireless-AC VPN Router Administration Guide 59 3 To configure dynamic RIP: STEP 1 Select Networking > Routing> RIP. STEP 2 In the RIP Basic Settings, configure the following settings: STEP 3 In the RIP Members area, check Enable RIP to enable RIP on all available interfaces (i.e. VLAN1, DSL_ATM, ETH_WAN, DSL_PTM). STEP 4 Click Edit to specify the following RIP authentication settings for an interface: STEP 5 In the RIP Authentication Settings, in Authentication, specify the authentication method fo

• Cisco RV132W, Administration Discovery Bonjour Configuration Cisco RV132W ADSL2+ Wireless-N and RV134W VDSL2 Wireless-AC VPN Router Administration Guide 132 8 STEP 4 In the Send E-Mail Logs by Schedule section, configure the following settings: STEP 5 In the Email Alert section, configure the following settings: STEP 6 Click Save. Discovery Bonjour Configuration Discovery Bonjour is a service advertisement and discovery protocol. On your device, Bonjour only advertises the default services configured on the device when Bonjour is enabled. To enable Discovery Bonjour: STEP 1 Select Administration > Discovery Bonjour. STEP 2 Check Enable to enable Bonjour. E-mail Authenticatio

• Cisco RV132W, Wireless Networks Basic Wireless Settings Cisco RV132W ADSL2+ Wireless-N and RV134W VDSL2 Wireless-AC VPN Router Administration Guide 76 4 Configuring the Security Mode You can configure one of the following security modes for wireless networks: Configuring WEP The WEP security mode offers weak security with a basic encryption method that is not as secure as WPA. WEP may be required if your network devices do not support WPA. NOTE If you do not have to use WEP, we recommend that you use WPA2. If you are using the Wireless-N only mode, you must u

• Cisco RV132W, Administration Session Timeout Configuration Cisco RV132W ADSL2+ Wireless-N and RV134W VDSL2 Wireless-AC VPN Router Administration Guide 124 8 NOTE You may download the user template to create your own list of user name and passwords. To download the template, click Download in the Download User template field. Session Timeout Configuration The timeout value is the number of minutes of inactivity that are allowed before the Device Manager session is ended. You can configure the timeout for the Admin and Guest accounts. To configure session timeout: STEP 1 Select Administrati

• Cisco RV132W, Cisco RV132W ADSL2+ Wireless-N and RV134W VDSL2 Wireless-AC VPN Router Administration Guide Contents Network Tools 127 Port Mirroring 128 Remote Support Key Settings 129 Logging Configuration 129 Configuring Log Settings 129 Configuring E-Mail Settings 131 Discovery Bonjour Configuration 132 LLDP Properties Configuration 134 Time Settings Configuration 134 Download and Backup Configuration File 135 Firmware Upgrade 138 Firmware Recovery Steps 139 Reboot 140 Restoring the Factory Defaults 140

• Networking Configuring LAN Settings Cisco RV132W ADSL2+ Wireless-N and RV134W VDSL2 Wireless-AC VPN Router Administration Guide 18 3 When the Internet Connection Type is RFC2684 Bridged (DHCP or Static mode) In the DSL Settings for the ATM transfer mode, enter the following information: Size Enter the size of bytes. (Range 576 - 1500, Default 1500). Transfer Mode A

• Cisco RV132W, Networking Configuring LAN Settings Cisco RV132W ADSL2+ Wireless-N and RV134W VDSL2 Wireless-AC VPN Router Administration Guide 27 3 For 6rd In the Other Settings section for the ATM and PTM (RV134W) transfer modes, enter the following: Address Mode Select Dynamic or Static. If you select Dynamic, it means that if the RA (Router Advertisement) message that the device receives, has an M Flag “0”, the device uses SLAAC (Stateless Address Auto-configuration) to get the IPv6 address; if the M Flag is “1”, the device uses DHCPv6 to get the IPv6 address. If you select Static, enter the following information: • IPv6

• Cisco RV132W, Networking Configuring LAN Settings Cisco RV132W ADSL2+ Wireless-N and RV134W VDSL2 Wireless-AC VPN Router Administration Guide 29 3 When the Internet Connection Type is PPPoA: In the DSL Settings section, enter the following information: MAC Address To set the MAC address of the device WAN port, do one of the following: To set the MAC address of the WAN port to your PC MAC address, click Clone My PC’s MAC. To specify a different MAC address, enter it in the MAC Address field. Transfer Mode AT M Multiplexing Defines the way in which different protoco

• Quality of Service (QoS) Configuring CoS Settings Cisco RV132W ADSL2+ Wireless-N and RV134W VDSL2 Wireless-AC VPN Router Administration Guide 120 7 Configuring CoS Settings Use the link to the QoS Port-Based Settings Page to map the CoS priority setting to the QoS queue. To map CoS priority settings to the traffic forwarding queue: STEP 1 Select QoS > CoS Settings. STEP 2 For each CoS pr

• Cisco RV132W, Wireless Networks Configuring Advanced Wireless Settings Cisco RV132W ADSL2+ Wireless-N and RV134W VDSL2 Wireless-AC VPN Router Administration Guide 81 4 Basic Rate The Basic Rate setting is not the rate of transmission but a series of rates at which the Services Ready Platform can transmit. The device advertises its basic rate to the other wireless devices in your network, so they know which rates will be used. The Services Ready Platform will also advertise that it will automatically select the best rate for transmission. The default setting is Default, w

• Cisco RV132W, Status and Statistics View Logs Cisco RV132W ADSL2+ Wireless-N and RV134W VDSL2 Wireless-AC VPN Router Administration Guide 11 2 View Logs The View Logs page can only be displayed if the user enables log at Administrator > Logging > Log Setting. Once this is enabled to view the logs, select Status and Statistics> View Logs. Click Refresh Rate, to display latest log entries. To filter logs or specify the severity of the logs to display, in the System Log Table, check the boxes next to the log type and click Go. Note that all log types above a selected log type are automatically included and you cannot deselec

• Administration Configuring TR-069 Settings Cisco RV132W ADSL2+ Wireless-N and RV134W VDSL2 Wireless-AC VPN Router Administration Guide 125 8 To update the Post-Login Banner Text fields, enter the login banner text in the text box. It is displayed on the CLI after user login. Configuring TR-069 Settings TR-069 is a DSL Forum specification for the CPE WAN Management Pr

• Cisco RV132W, Networking Configuring LAN Settings Cisco RV132W ADSL2+ Wireless-N and RV134W VDSL2 Wireless-AC VPN Router Administration Guide 67 3 STEP 3 Click Save. Configuring Advertisement Prefixes To configure the RADVD available prefixes: STEP 1 Select Networking > IPv6 > Advertisement Prefixes. STEP 2 Click Add Row. STEP 3 Enter the following information: Router Preference Select low, medium, or high from the drop-down menu. The default is medium. The router preference provides a preference metric for default routers. The low, medium, and high values are signaled in unused bits in RA messages. This extension is backward compatible, both for routers (se

• Networking Configuring LAN Settings Cisco RV132W ADSL2+ Wireless-N and RV134W VDSL2 Wireless-AC VPN Router Administration Guide 21 3 In the Other Settings section for both the ATM and PTM (RV134W) transfer modes, enter the following information: NAT (Network Address Translation) If enabled, all outbound traffic through this interface is NAT’ed. If disable, all outbound traff

• Cisco RV132W, Networking Configuring LAN Settings Cisco RV132W ADSL2+ Wireless-N and RV134W VDSL2 Wireless-AC VPN Router Administration Guide 47 3 Configuring a Mobile Network Choose Networking > WAN > Mobile Network to configure the device to connect to a Mobile Broadband USB modem that is connected to its USB interface. 802.1p Priority Enter a range from 0 to 7. All outbound traffic of this interface will be tagged with the configured 802.1p priority. If it conflicts with the QoS setting, the QoS setting will take precedence. MTU (Maximum Transmission Unit) MTU is an advanced configuration that allows you to determine the largest data size per

More Instructions:

	Cisco RV132W Quick start manual 18-02-2024 13	DOWNLOAD
	Cisco RV132W Quick start manual 26-07-2023 13	DOWNLOAD
	Cisco RV132W Command line interface reference manual 10-11-2022 52	DOWNLOAD

Related Products and Documents (Wireless Router):

Comparable Devices:

Similar Resources:

• Linksys WRT54G3G - Wireless-G Router For Verizon Wireless Broadband (2 pages) Model No.Product DataWirelessWRT54G3G (EU)Share your 3G Internet Connection!All-in-one Internet-sharing Router, 4-port Switch, and Wireless-G (802.11g) Access PointHigh security: Wi-Fi Protected Access™ (WPA/WPA2 Personal), wireless MAC address filtering, powerful SPI firewallShares a Vodafone 3G/UMTS or GPRS Internet connection and other resources with Et …

• TP-Link Archer CR700 (2 pages) Quick Installation GuideAC1750 Wireless Dual Band DOCSIS 3.0Cable Modem RouterConnect to the Internet4Upstream: Solid Online: SolidWireless: SolidDownstream: Solid Power: Solid Wait about 15 minutes for the modem router to synchronize with the Internet service provider's (ISP) server and make sure the following LEDs are on.7106505264 REV1.0.1Archer …

• GlobalScale MiraBox (27 pages) MiraBoxUser Guide –page1 / 27 MiraBox User Guide Contents A. Package contents.............................................................................................................................................. 2 B. MiraBox appearance and connecting ports.................................................................................. …

• Cisco AIR-AP1230B-A-K9 - Syst. 1230 Aironet WLAN AP (138 pages) Americas HeadquartersCisco Systems, Inc.170 West Tasman DriveSan Jose, CA 95134-1706 USAhttp://www.cisco.comTel: 408 526-4000800 553-NETS (6387)Fax: 408 527-0883Cisco Aironet 1200 Series Access Point Hardware Installation Guide December 2006Text Part Number: OL-8370-04 …

• Cisco AIR-AP1121G-E-K9 (122 pages) Corporate HeadquartersCisco Systems, Inc.170 West Tasman DriveSan Jose, CA 95134-1706 USAhttp://www.cisco.comTel: 408 526-4000800 553-NETS (6387)Fax: 408 526-4100Cisco Aironet 1100 Series Access Point Hardware Installation GuideOctober 2003Text Part Number: OL-4309-02 …

• Verizon Jetpack MiFi 8800Li (4 pages) Jetpack MiFi 8800Li HOTSPOT Instructions1. Most Jetpacks come with the SIM card and battery already installed! Jetpack MiFi 8800 Li HOTSPOTJetpack MiFi 8800Li Hotspot SetupThe Jetpack MiFi 8800Li hotspot that was provided to you from Boston Public Schools is serviced through Verizon. The hotspot comes with 3 months of pre-paid internet service provided by BP …

Comments, Questions and Opinions: