Alarm Lock PG21 Series Installation Instructions Manual

Text of Alarm Lock PG21 Series User Guide:

• Alarm Lock PG21 Series, 1 PG21 Series Pilfergard Door Alarms INSTALLATION INSTRUCTIONS WI738F 1/06 345 Bayview Avenue Amityville, New York 11701 For Sales and Repairs, (800) 645-9445 For Technical Service, (800) 645-9440 © ALARM LOCK 2006 ALARM LOCK DESCRIPTION The PG21 is a microprocessor-controlled door alarm for sur- face mounting on a door or door frame. Typical applications include emergency fire escape doors, nursing home stairwell doors, rear restaurant and theater doors. The PG21 is de- signed to continually monitor the status of a doo

• Alarm Lock PG21 Series, 2 7. Position the Magnetic Actuator as indicated by the red sticker on the side of the Housing Cover. If stickers were removed, use the Magnet Alignment Mode (see page 3) or place the Magnetic Actuator 1½ " from the bottom edge of the Baseplate. Mark holes and (as with the Baseplate) use a 1/8" (0.125") bit, and drill the hole 1" deep. 8. Install the Magnetic Actuator with the supplied #8 sheet- metal screws (1"). Be sure to insert the Magnet (P1358) and Magnet Cover (P0291) into the Magnet Housing (P0290) before mounting. B.

• 3 2. Reed selection jumper W1 is located in the center of the PCB. The jumper should be set to the side of the unit that will have the magnet installed. (See Figure 5 below). 3. Select jumper options (J1- J9) as follows. (Refer to the Jumper Options table, below and page 5). Important: The jumpers are only read at startup and when- ever the

• 4 D. MOUNTING Before mounting, install a mortise cylinder into the Housing Cover (H354-28) as follows: 1. Referring to the Figure 5 at right, (a) install mortise cylinder (Alarm Lock Model CEM, optional) into the Housing Cover from the outside with the key slot at the 6 o'clock position; (b) install the Locking Arm (HW1154). Be sure to

• Alarm Lock PG21 Series, 5 MODE NAME FEATURE DETAILS JUMPER POSITIONS Factory Default Highest Security Fire/Emergency Exit Door Nursing Home Stairwell Door Delivery Door--Latching Alarm Opening door without key while armed causes a latching alarm (key required to silence). Key required to exit and to turn off siren after an alarm. Alarm siren time-out: 2 minutes. After time-out, LED flashes. Door can be propped open indefinitely, as follows: Turn key to the left while opening door (this avoids alarm). After door is opened, re- lease key. Door can be

• Alarm Lock PG21 Series, 6 MODE NAME FEATURE DETAILS JUMPER POSITIONS For Multiple Door Installa- tions A PG21 installed on several doors each with its unique siren sound. Four siren sounds: Sweep, Pulsing Sweep, Steady, Pulsing Steady. Set a different siren sound for each door in order to easily identify which door has been accessed. Jumpers 1 and 2 are config- ured. Sweep Pulsing Sweep Steady Pulsing Steady Door Ajar Mode Exit/Entry Door without Key Needed No Key Passage Mode Friendly Mode You can en

• Alarm Lock PG21 Series, 8 ALARM LOCK LIMITED WARRANTY ALARM LOCK SECURITY SYSTEMS, INC. (ALARM LOCK) warrants its products to be free from manufacturing defects in materials and workmanship for 24 months following the date of manufacture. ALARM LOCK will, within said period, at its option, repair or replace any product failing to operate correctly without charge to the original purchaser or user. This warranty shall not apply to any equipment, or any part thereof, which has been repaired by others, improperly installed, improperly used, abused, altered, damaged

More Instructions:

Alarm Lock PG21 Series Installation template 02-08-2022 2

DOWNLOAD

Related Products and Documents (Security System):

Comparable Devices:

Similar Resources:

• Digicom Pocket AL I/O (36 pages) Pocket AL I/OUser’s Guiderev. 1.0 04/2010Alarm System via SMS 900/1800MHz Dual Band GSM Module Remote control of sensors Configuration through GSM phone Rechargeable Backup Battery6 IN & 6 OUT …

• My ADT Ademco Vista-10P (4 pages) For a detailed review of the entire system, please view the Ademco Vista – 10P system manual. Arm and Disarm Arm:  To arm in STAY mode when you are not leaving the premises, enter your [security code] + [STAY].  To arm in AWAY mode when you are leaving the premises, enter your [security code] + [AWAY]. …

• Cisco 500 Series (42 pages) Americas Headquarters:© 2008 Cisco Systems, Inc. All rights reserved.Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USARegulatory Compliance and Safety Information for the Cisco Secure Router 500 SeriesRead this document before installing or servicing the Cisco Secure Router 520 Series router.Note Only trained and qualified service per …

• KE2 Local Area (24 pages) KE2 Therm’s Local Area Dashboard & Alarms (LDA) is the perfect addition to the Refrigeration Network. When the KE2 LDA is connected to the same network as KE2 Therm controllers, it immediately and automatically scans and finds all KE2 Therm controllers – Ethernet or Serial-ModBus. Serve as a Permanent WiFi Service Tool Display a Local Area Dashboa …

• Heath Zenith CB-2010 (12 pages) OPERATIONModel CB-2010Motion SensorLight Control withProtective LampShields© 2000 Heath Co. a div. of DESA International 598-1090-00* resets to Auto Mode at dawn.TESTLight ControlSensorCoverPlateLampHolders6 Screws(3 sizes included)GasketFeatures• Turns on lighting when motion is detected.• Automatically turns lighting off.• Photocell keeps the lighti …

• Pfannenberg PY L-S (10 pages) Sicherheitshinweise / Kurzanleitung PY L-S GEFAHR - Kennzeichnet eine außergewöhnlich große Gefahrensituation. Wird dieser Hinweis nicht beachtet, kommt es zu schweren irreversiblen Verletzungen oder zum Tod. WARNUNG - Kennzeichnet eine außergewöhnlich große Gefahrensituation. Wird dieser Hinweis nicht beachtet, sind schwere irreversible oder tödliche …

Comments, Questions and Opinions: