Cube FC2020-P1 Quick User Manual
|
Cube FC2020-P1, Table of Contents Before Installation ................................................................................................................. 1 I. Camera Introduction .................................................................................................... 1 1. Package Contents ............................................................................................... 1 2. Hardware Installation ........................................................................................... 2 2.1
Cube FC2020-P1, 1 Before Installation Before installation, please be sure to read this quick installation guide and user’s manual carefully to complete the installation. I. Camera Introduction The following section introduces package contents, hardware installation, factory default reset, and SD card Compatibility List of each type camera. 1. Package Contents Item Descriptions 1. FC2020-P1 2. Bracket 3. Screw pack 4. Power Adaptor(DC 12V/0.5A) (Optional) 5. CD (User’s Manual and Quick Guide, NVR software included) **If any of the above items are missing, ple
Cube FC2020-P1, 2 2. Hardware Installation 1. Install with bracket Please refer to the picture for camera installation. Use the screws to lock the bracket to the wall or ceiling, and then connect the camera to the bracket. There’s a knob on the back of the bracket. Loosen the knob and you can adjust the angle of camera. Tighten it to fix the angle.
Cube FC2020-P1, 3 2. Connector Instruction The camera connectors are as below. Connect the power and the Ethernet cable with the camera, and set it according to your network environment. AUDIO OUT ETHERNET DI/DO DC 12V POWER DEFAULT BUTTON MICRO SD CARD SLOT PIR SENSOR MICROPHONE 3. I/O Configuration I/O Connection
Cube FC2020-P1, 4 a. Please connect the G & DO pin to the external relay (buzzer) device When no event happens, DO output is 5V (DO and GND are disconnected). When the camera detects event happening and triggers external alarm, DO output is 0V (DO and GND are connected). b. Please connect the G & DI pin to the external trigger device. If you select "N.O" in "Input sensor setting", when external devise or circuit makes DI and GND pin connected, the camera input alarm is triggered, and then camera will execute the action user has set, for example, send sn
5 2.1 Factory Default 1. To recover the default IP address and password, please follow the following steps. 2. Remove power and Ethernet cable. 3. Press and hold the button and connect power and Ethernet cable to the camera again and hold for round 20 seconds for system booting. 4. Release the button when camera finishes proceed. 5. Re-login the came
Cube FC2020-P1, 6 3. SD card Compatibility List FC2020-P1 is compliant with microSD/SDHC card and to ensure recording quality, and please use The following memory cards. MicroSD/SDHC card Transcend SDHC class4 32GB Transcend SDHC class10 64GB SanDisk SDHC class4 32GB SanDisk SDHC class10 64GB
Cube FC2020-P1, 8 III. IP Assignment There are two ways to find IP Cameras: Finding IP Camera by using the “NXU Lite recording software” Finding IP Camera by using the “AVer IPCam Utility” Finding IP Camera by using “NXU Lite recording software” 1. The NXU Lite software is in the attached software CD. Before launching it, please install the software first. During the installation process, users will be required to input a User name and Password for login NXU Lite system. Users can define the User name and Password as desired. Please refer to the NXU Lite user manua
Cube FC2020-P1, 10 6. Enter IP Camera’s ID and Password (default is admin/admin) and click “Auto Search” to find camera. 7. In the Search Result window, click the IP camera model that the user has purchased (Please ignore ONVIF connection item); the camera is in red text that is configurable. Users can double-click on the camera in the red text and configure the IP camera’s settings; even if the IP camera is not in the same IP segment. Press “OK” to go back to the previous screen and press ”Connect” to start live view. Double-click the IP camera model
Cube FC2020-P1, 11 Finding IP Camera by using “AVer IPCam Utility” 1. Use the software, “AVer IPCam Utility” to assign the IP address of the IP camera. The software is in the attached software CD. 2. Run the IPCam Utility 3. Select the proper network adapter and click [Search] to begin searching. 4. Select and double click the IP camera you want to access. If you want to change the setting of the selected IP camera, enter the user ID, correct password, and change the settings and then click Apply button. This will change the setting and
12 5. The IE browser will open and direct you to the IP camera login page. This requires IPViewer.ocx to run. If the IE ActiveX warning message appears, click to allow running the add-on. [Note] The default IP address is: 192.168.1.168 The default ID and Password are both ”admin”. You can’t enter a device name in Chinese or any other special characters (&
Cube FC2020-P1, 13 Using NON-DHCP Server/Router Network In Non-DHCP server/router network, the static IP address must be assigned to the device each time when adding another IP camera to the network; the default IP address of the current one must be changed to avoid conflict. Please make sure the Subnet of the PC’s IP address and the IP camera’s IP address are the same. [Example] The same Subnet: IP camera IP address: 192.168.1.168 PC IP address: 192.168.1.100 Different Subnets: IP camera IP address: 192.168.1.168 PC
Cube FC2020-P1, 14 IP camera IP addresses: A quick way to access remote monitoring is to double-click on a selected IP camera in “Camera Name list” in AVer IPCam Utility. Then, the IE browser will open and connect to IP camera. Then, please key in the default “ID” and “Password”, both of which are “admin”.
Cube FC2020-P1, 15 IV. Connecting the IP Camera Launch the Internet Explorer browser, type the IP address of the IP camera in the address field. It will show the following dialogue box. Key-in the ”ID” and “Password”. The default ”ID” and “Password” are both “admin”. Once connected to the IP camera, the following program interface will appear.
Cube FC2020-P1, 16 FCC NOTICE (Class A) This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Federal Communications Commission Statement NOTE- This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
Cube FC2020-P1, 17 THE MARK OF CROSSED-OUT WHEELED BIN INDICATES THAT THIS PRODUCT MUST NOT BE DISPOSED OF WITH YOUR OTHER HOUSEHOLD WASTE. INSTEAD, YOU NEED TO DISPOSE OF THE WASTE EQUIPMENT BY HANDING IT OVER TO A DESIGNATED COLLECTION POINT FOR THE RECYCLING OF WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT. FOR MORE INFORMATION ABOUT WHERE TO DROP OFF YOUR WASTE EQUIPMENT FOR RECYCLING, PLEASE CONTACT YOUR HOUSEHOLD WASTE DISPOSAL SERVICE OR THE SHOP WHERE YOU PURCHASED THE PRODUCT. Limited Warranty AVer Information, Inc. (“AVer
18 Limitation of Liability In no event shall aver be liable for indirect, incidental, special, exemplary, punitive, or consequential damages of any nature including, but not limited to, loss of profits, data, revenue, production, or use, business interruption, or procurement of substitute goods or services arising out of or in connection with this limited warrant
Cisco Nexus 7000 Series IP Camera Configuration manual
Nexus 7000 Series |
Q-See QC Series IP Camera Operation & user’s manual
QC Series |
Zavio F312A IP Camera Hardware user manual
F312A |
Voltek SuperCam 2 CT150 IP Camera Installation instructions manual
SuperCam 2 CT150 |
Jabra PRO 920 IP Camera Quick start manual
PRO 920 |
Foscam FI9805W IP Camera Operation & user’s manual
FI9805W |
Foscam FI8919W IP Camera Operation & user’s manual
FI8919W |
Axis Network Camera AXIS 221 IP Camera Brochure
Network Camera AXIS 221 |
# | Manufacturer | Model | Document Type | File | Updated | Pages | Size |
---|---|---|---|---|---|---|---|
1 | Amana | Automatic Dryer | Installation instructions manual | amana/automatic-dryer-8FY.pdf | 18 Feb 2024 | 37 | 0.98 Mb |
2 | American DJ | DJ Scan 250 | User instructions | american-dj/dj-scan-250-FCD.pdf | 23 Jul 2023 | 8 | 0.67 Mb |
3 | Zvork | Oberon | Operation & user’s manual | zvork/oberon-1I6.pdf | 14 Dec 2023 | 28 | |
4 | VXI | TalkPro Headset | Operation & user’s manual | vxi/talkpro-headset-85C.pdf | 06 Sep 2023 | 2 | 0.13 Mb |
5 | Zoom | 505 GUITAR | Operation manual | zoom/505-guitar-QFT.pdf | 17 Feb 2023 | 6 | 0.19 Mb |
6 | SEVERIN | WK3496 | User manual manual | severin/wk3496-2O6.pdf | 02 Sep 2023 | 6 |
Honeywell
Performance Series Network Video Recorder User Guide HEN081*4 HEN162*4 HEN163*4 HEN161*4 HEN322*4 HEN323*4 HEN321*4 HEN642*4 HEN643*4 HEN041*3 HEN081*3 HEN161*3 HEN04103L HEN08103L HEN16103L HEN32103L (* = Storage in TB)
…
2450Cm Series(276 pages) |
Siqura
Step 2: Determine installation location Determine where you are going to install your BC820H1-SFP. Use the Siqura WM04 Wall Bracket sold separately for BC series cameras (figure 2). Make sure that the provided surface has sufficient strength to support the camera. Figure 2 The BC820H1-SFP camera screws onto a mounted wall bracket Step 1: Ch …
BC820H1-SFP(2 pages) |
Lorex
4K Ultra HD Bullet IP CameraE861AB_QSG_EN_R2Quick Start GuideEnglish Version 2.0Copyright © 2019 Lorex Corporation As our products are subject to continuous improvement, Lorex reserves the right to modify product design, specifications and prices, without notice and without incurring any obligation. E&OE. All rights reserved.• For a full list of comp …
E861AB Series(2 pages) |
D-Link
VIDEO ON-THE-GOThe D-Link Wireless Pan/Tilt Internet Camera (DCS-5220) is the ultimate remote surveillance solution that allows viewing of a live video feed on a compatible 3G mobile phone or PDA. It is perfect for users that are often on the road and desire around-the-clock monitoring for applications such as home/offi ce surveillance, checking up on infan …
DCS-5220(2 pages) |
Cisco
Corporate Headquarters:Copyright © 2004 Cisco Systems, Inc. All rights reserved.Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USAPrefaceThis preface describes the objectives, audience, organization, and conventions of the software configuration documentation for your router. It contains the following sections: •Objectives, page 1 …
2800 Series(266 pages) |
ETS
459a_359a_459ah_359ah_565a_561_552a_V0.9 IP CAMERA SERIES OPERATION GUIDE Please read instructions thoroughly before operation and retain it for future reference.
…
IP CAMERA SERIES(39 pages) |
Victory Refrigerator VUR3-BTVUR3-BT Installation, operation and troubleshooting instructions - ZMVL2P VUR3-BT, 17 |
Karcher Pressure Washer K 2.16#7OEQP2: K 2.16 Pressure Washer Operator's manual K 2.16, 48 |
Truma Air Conditioner Frostair 1500Frostair 1500 Installation instructions manual - SX6D8J Frostair 1500, 8 |
TufFlight Toy BouncerTufFlight Toy Instruction manual (File: tufflight-bouncer-toy-32, 12th Dec 2023) Bouncer, 32 |
First Alert Security Sensors CO615First Alert Product User Manual: CO615 PDF Operation & user’s manual - N574WZ CO615, 2 |
Lennox Furnace ML193DF#5RUN6X ML193DF: Lennox Furnace Owner Documentation ML193DF, 48 |
Cooper Lighting Landscape Lighting CML SQUARE CML40MN3VSGBKLCooper Lighting CML SQUARE CML40MN3VSGBKL Manual (Specification sheet), @L74RPS CML SQUARE CML40MN3VSGBKL, 2 |
Samsung Computer Accessories BG68-01825AUser Manual: Samsung BG68-01825A (MIG81Z, Upd.11th Nov 2023) BG68-01825A, 2 |
Schumacher Racing Products Battery Charger UDC-10Instruction manual for Schumacher Racing Products UDC-10 Battery Charger UDC-10, 2 |
Homelite Trimmer UT44172Homelite Trimmer UT44172 Operator's manual UT44172, 38 |
NETGEAR Switch JGS524EJGS524E Installation manual - X3TPH7 JGS524E, 2 |
Maytag Dryer Electric and gas dryerDryer PDF Use and care manual Electric and gas dryer, 28 |