Atlantis host power 1101rc Operation & User’s Manual
|
Atlantis host power 1101rc, 69 Fault code is shown as 27 and the icon is li g htin g on LCD display and alarm is continuously sounding. Battery volta g e is too hi g h or the charger is fault. Contact Atlantis SpA. Fault code is shown as 28 and the icon is li g htin g on LCD display and alarm is continuously sounding. Battery volta g e is too low or the charger is fault. Contact Atlantis SpA. The icon and the icon are flashin g on LCD display and alarm is soundin g twice every second. UPS is overload Remove excess loads from UPS output. Fault code is shown as 43 and The
72 A.1.5 Support For technical questions and support, please contact our help-desk by ticket on http://www.atlantis-land.com/ita/supporto.php. For generic informations, please send an e-mail to [email protected] . For presales informations, please send an e-mail to [email protected] . Atlantis SpA Via S. Antonio, 8/10 20020 Lainate (MI) Fa
Atlantis host power 1101rc, 79 CONNECTIONS Output 8 xIEC 320 (Battery Power Supplied) 4 xIEC 320 (Programmable) Computer USB/RS232 (USB port and RS-232 port can’t work at the same time) SNMP Slot Backu p Time 10 to 30 mins for t yp ical PC Load MECHANICAL Dimensions (WxHxD): 380 x 438 x 88 (2U) mm Net Weight(with Battery): 12,9 Kg 14,3 Kg ENVIRONMENTS T em p erature 0°-40° C Humidity 0-90% (non-condensin g ) Noise Level Less then 45 dB Packa g e Contents Host Power RC Line Interactive SineWave UPS
Atlantis host power 1101rc, 41 Benché il gruppo supporti la modalità Hot Swap è consigliabile spegnere e scollegare tutti i carichi, spegnere il gruppo e staccarlo dalla linea elettrica. Sostituzione del pacco batterie Step 1 (Rimuovere il pannello frontale). Step 2 (Sconnettere il pacco batterie, scollegando i 2 appositi connettori). Step 3 (Rimuovere le 2 viti ed estrarre il pacco batterie).
50 Number Explanations 1 Pro g rammable outlets: connect to non-critical loads 2 Output receptacles: connect to mission-critical loads 3 AC input 4 Input circuit breaker 5 Network/Fax/Modem sur g e protection 6 Emer g ency power off function connector (EPO) 7 USB communication port 8 RS-232 communication port 9 SNMP intelli g ent slot 10
Atlantis host power 1101rc, 66 Standb y Mode UPS is powered off and no output supply power, but still can charge batteries. 3.8 Faults Reference Code Fault event Fault code Icon Bus start fail 01 x Bus over 02 x Bus under 03 x Inverter soft start fail 11 x Inverter volta g e high 12 x Inverter volta g e Low 13 x Inverter output short 14 Battery volta g e too high 27 x Battery volta g e too low 28 Over temperature 41 x Over load 43
Atlantis host power 1101rc, 36 l’icona e l’icona è lampe gg iante mentre viene riprodotta una se g nalazione acustica (2 beep al secondo). condizioni di overload. V iene visualizzato il messa gg io di errore N°43 e l’icona è accesa mentre viene riprodotta una se g nalazione acustica continua. L’UPS si spe g ne automaticamente a causa di un overload continuativo. Sconnettere parte del carico e riavviare l’UPS. V iene visualizzato il messa gg io di errore N°14 mentre viene riprodotta una se g nalazione acustica continua. L’UPS si spe g ne automaticamente a causa di un corto circuito in uscita. Co
8 di dati da questo generati. Il software è stato testato solo in ambiente Windows (alcun supporto per Linux/MAC OS X verrà fornito). Per usufruire delle condizioni di g aranzia migliorative associate al prodotto (Fast Swap, On Site e On Center) è opportuno provvedere alla registrazione dello stesso sul sito www.atlantis- land.com entro e non oltre 15 giorni
Atlantis host power 1101rc, 31 Batter y Quando il volta gg io in in g resso è fuori finestra o assente, l’UPS alimenta il carico utilizzando l’energia delle batterie. In questo caso emette un suono ogni 10 secondi. Standb y Mode L’UPS è spento e nessun carico connesso è alimentato, ma se collegato alla rete elettrica l’UPS può caricare, se necessario, le batterie.
Atlantis host power 1101rc, 27 04: Configurazione Orientamento Display (LCD display direction setting) Interfaccia Confi g urazione R A C: Rac k display confi g urato per modalità Rack (orizzontale). TOE: Tower display configurato per modalità Tower (verticale). 00: Uscita Modalità Configurazione (Exit setting) Premere per uscire dalla modalità configurazione. Si ricorda che i pro g rammi disponibili sono 4: 0: Uscita 1: Voltaggio 2: Abilitazione Uscite programmabili 3: Configurazione timing delle Uscite programmabili 4: Configurazione orientamento Display Scollegare il cavo di connessione alla rete elettrica ed aspettare che il Display s
47 Important information for the correct recycle/treatment procedures of this equipment The crossed-out wheeled bin symbol printed on the unit label or unit packaging indicates that this equipment must not be disposed of as unsorted municipal waste but it should be collected separately. The waste of electric and electronic equipment must be treated separately, in order
Atlantis host power 1101rc, 28 3.6 Esempio di configurazione (UPS Setting) Si voglia seguire l’esempio seguente per impostare le uscite programmabili per un funzionamento sino a 3 minuti. Step LCD Confi g urazione 1 Prima di entrare in modalità configurazione l’UPS deve essere spento (con le batterie connesse) e collegato alla linea elettrica. Il display dovrebbe essere come nell’immagine a fianco. 2 Premere il bottone Select per 10 secondi per entrare in modalità configurazione (il sistema em
Atlantis host power 1101rc, 53 2.3 Setup The UPS Step 1: UPS input connection Plug the UPS into a two-pole, three-wire, grounded receptacle only. Avoid using extension cords. Step 2: UPS output connection There two kinds of outputs: programmable outlets and general outlets. Please connect non-critical devices to the programmable outlets and critical devices to the general outlets. During power failure, you may extend the backup time to critical devices by setting shorter backup time for non-critical devices. Step 3: Communication connection Communic
Atlantis host power 1101rc, 71 A.1.3 ViewPower Situation Solution How to install the Software. Once started the UPS you can connect it to PC throu g h USB cable. At this time the SO detects and installs automatically all drivers. Now you can install ViewPower on the PC. PC doesn’t find the UPS. 1. Check if the cable is properly connected 2. Use the original cable 3. Verify Your IP and please chan g e if You are usin g 192.168.5.x subnet. A.1.4 Opeartion/Storage The UPS system contains no user-serviceable parts. If the ba
Atlantis host power 1101rc, 60 3.4 LCD Display Wordings Index Abbreviation Display content Meaning ENA Enable. DIS Disable. ESC Escape. EP EPO. FA Fan. TP Temperature. CH Charger. RAC Rack display. TOE Tower display. SF Site Fault.
Atlantis host power 1101rc, 33 3.9 Allarmi Allarme Icon (Lampeggiante) Alarme Sonoro Batterie Scarica (Low Battery) Suono ogni secondo. Sovraccarico (Overload) Suono 2 volte al secondo. Batterie non connessa (Battery is not connected) Suono ogni secondo. Sovraccarico delle batterie (Overcharge) Suono ogni secondo. Connessione a terra/fase errata (Site wiring fault) Suono ogni secondo. EPO attiva (EPO enable) Suono ogni secondo. Problemi Ventola (Fan Failure) Suono ogni secondo. Temperatura elevate (Over temperature) Suono ogni secondo. Caricatore guasto (C
32 3.8 Tabella Errori Malfunzionamento Indicativo errore Icona Problemi sul BUS (Bus start fail) 01 x Tensione elevata sul Bus (Bus over) 02 x Tensione bassa sul Bus (Bus over) 03 x Problemi sul all’Inverter (Inverter soft start fail) 11 x V olta gg io Elevato sull’inverter (Inverter voltage high) 12 x V olta gg io Bassosull’inverter Inverter v
Atlantis host power 1101rc, 54 Step 4: Network connection Network/Fax/Phone surge port Connect a single modem/phone/fax line into surge-protected “IN” outlet on the back panel of the UPS unit. Connect from “OUT” outlet to the equipment with another modem/fax/phone line cable. Step 5: Disable and enable EPO function Keep the pin 1 and pin 2 closed for UPS normal operation. To activate EPO function, cut the wire between pin 1 and pin 2.
Atlantis host power 1101rc, 26 02: Attivazione Uscite Programmabile (Programmable outlets enable/disable) Interfaccia Confi g urazione ENA: Abilita le uscite (IEC) pro g rammabili. DIS: Disabilita le uscite (IEC) programmabili. 03: Uscite Programmabile (Programmable outlets setting) Interfaccia Confi g urazione E’ possibile impostare il tempo di funzionamento in minuti (tra 0-999) delle uscite (IEC) programmabili. L’UPS passato tale intervallo, dal funzionamento in modalità batteria, smetterà di alimentare queste uscite per salvare l’energia rimanente destinandola ai soli carichi critici co
Atlantis host power 1101rc, 43 Assemblaggio del Battery Kit Assembly Il pacco batteria va rimosso dall’UPS, va aperto e vanno cambiate le batterie e va poi nuovamente inserito nell’UPS. Seguire la procedura seguente per il cambio delle batterie. Step 1 (Rimuovere le batterie esauste). Step 2 (Connettere le batterie seguendo gli schemi sotto riportati, diversi a seconda del numero di batterie utilizzatae dal dispositivo). Step 3 (Appoggiare le batterie ad uno dei 3 supporti plastici). Step 4 (Chiudere il pacc
Atlantis host power 1101rc, 82 Backup TIME & Battery Code A 03-HP3351-RC 43 24 18 9 6 3 2Min A 03-HP2001-RC 31 17 13 5 2,5 Min A 03-HP1501-RC 18 9 5 1,5 Min A 03-HP1001-RC 13 4 2,5 min Power Ratin g (W) 330 480 640 880 1200 1500 2000 A 03-HP2001-RC Battery Low 44.4 V ±2VDC Battery CutOFF 40.0V ± 2VDC Battery Char g in g Volta ge 55.2V ± 1.6 V D C A 03-HP33511-RC Battery Low 66.6 V ±2VDC Battery CutOFF 60.0V ± 2VDC Battery Char g in g Volta ge 82.8V ± 2.4 V D C A 03-H P 1001-RC/1501-RC Battery Low 22.2 V ±1VD C Battery CutOFF 20.0V ± 1VD C
Atlantis host power 1101rc, 29 Selezionare il programma 02 e cliccare su OFF/Enter, cliccare su ON/MUTE sino a che sul display venga visualizzato ENA e cliccare OFF/Enter per uscire. 4 Selezionare il pro g ramma 03 e cliccare su OFF/Enter, cliccare su ON/MUTE sino a che sul display venga visualizzato 3 e cliccare OFF/Enter per uscire. Al solito ogni bottone va premuto sino a che il dispositivo non emette un fischio. 5 Selezionare il pro g ramma 04 e cliccare su OFF/Enter per uscire. Al solito ogni bottone va premuto sino a che il dispositivo non emette un fischio. 6 Scolle g are il cavo di connessione alla rete elettrica ed aspettare che il Disp
Atlantis host power 1101rc, 45 Preparation Condensation may occur if the UPS system is moved directly from cold to warm environment. The UPS system must be absolutely dry before being installed. Please allow at least four (5) hours for the UPS system to acclimate the environment. Do not install the UPS system near water or in moist environments. Do not install the UPS system where it would be exposed to direct sunlight or near heater. Do not block ventilation holes in the UPS housing. Installation Do not connect appliances or devices which would overload the UPS system (e.g. laser printers) to the
Atlantis onepower 841 UPS Operation & user’s manual
onepower 841 |
Atlantis HostPower 1102 UPS Operation & user’s manual
HostPower 1102 |
Atlantis onepower 701 UPS Manual manual
onepower 701 |
Santak C1KR(S) UPS Operation & user’s manual
C1KR(S) |
Delta Electronics INX-1K UPS Operation & user’s manual
INX-1K |
OPTI-UPS Gaming Series GS1100B UPS Specifications
Gaming Series GS1100B |
Eaton Powerware 5125 UPS Operation & user’s manual
Powerware 5125 |
Atlantis LinePower 1151 UPS Manual
LinePower 1151 |
# | Manufacturer | Model | Document Type | File | Updated | Pages | Size |
---|---|---|---|---|---|---|---|
1 | Omnia | Omnia-3 | Installation and operation manual | omnia/omnia-3-7R4.pdf | 03 Jul 2023 | 98 | |
2 | Samsung | FG87KST | Owner's instructions and cooking manual | samsung/fg87kst-1U8.pdf | 13 Mar 2024 | 24 | 1.37 Mb |
3 | H3C | LS-5100-16P-SI-OVS-H3 | Configuration | 3com/ls-5100-16p-si-ovs-h3-K57.pdf | 04 May 2023 | 313 | 4.39 Mb |
4 | ProForm | 790 Zlt Cwl Treadmill | Manual | proform/790-zlt-cwl-treadmill-3TA.pdf | 08 Nov 2023 | 32 | |
5 | Frigidaire | FAS224J2A2 | Factory parts catalog | frigidaire/fas224j2a2-924.pdf | 11 May 2023 | 12 | |
6 | Oregon Scientific | HOT WHEELS FAST TRACK LAPTOP | Manual | oregon-scientific/hot-wheels-fast-track-laptop-TUC.pdf | 17 May 2023 | 40 |
Zipato
DECLARATION OF CONFORMITY Tri plus grupa d.o.o. declares that this product is in compliance with the essential requirements and other relevant provisions of Directives as follows: Model: ZIPABOX-BACKUP-V5 Intented use: indoor EMC Directive (2004/108/EC) Low Voltage Directive (2006/95/EC) R&TTE Directive (1999/5/EC) The product is compatible wit …
ZIPABOX-BACKUP-V5(3 pages) |
Emerson
PowerSure™ PSTQuick-Start Guide for 500-650VA; 230VWHAT’S IN THE BOX• Quick-Start guide• PowerSure family user manualon CD (also at www.liebert.com)• Warranty card• USB cable (PAXXX-230U models only),1.8m (6ft.)• RJ-11 cord, 2.1m (7 ft.)• Two (2) 10A output power cords, 2.0m (6.6 ft.)For more details, refer to the PowerSure user manual on CD. …
Liebert PowerSure PST(2 pages) |
Toshiba
Uninterruptible Power System (UPS)G8000 SeriesInstallation Manual• Read this operation manual carefully beforeinstalling the UPS.• Retain this manual with the UPS for easyreference when required.• This manual was written for the consultingengineer, architect, and electrical contractor.© TOSHIBA Corporation 2005All Rights Reserved.REQUIREMENTSDocume …
G8000 Series(41 pages) |
TEC
PRELIMINARY 1 UUnniinntteerrrruuppttiibbllee PPoowweerr SSuuppppllyy Manuale d’uso Sirius 10 - 12 - 15 - 20kVA Ingresso trifase / uscita monofase MULTISTANDARD PRELIMINARY 2 INTRODUZIONE Vi ringraziamo per la scelta del nostro prodotto. La nostra azienda è specializzata nella progettazione, nello sviluppo e nella produzione di …
sirius(126 pages) |
Trust
Quick Installation Guide17238UPSwww.trust.com/17238/faqVACINPUT OUTPUT VACLINE MODE VDCHZVACINPUT BATTERY OUTPUT LOADVACHZ%LINE MODE (AVR)BACKUP MODEFAULTOUTPUTPRESS TO RESETINPUTINOUTPOWERPCMonitorMonitori2InstallationOUTPUTPRESS TO RESETINPUTINOUTADBFCE1G IH JVACINPUT OUTPUT VACLINE MODE
…
17238(66 pages) |
GE
g GE SGT5000_030-040_UPS_GE_01 SG Series 10, 20, 30 and 40 kVA OPERATING MANUAL UNINTERRUPTIBLE POWER SUPPLY Digital Energy TM SG Series 10 – 20 – 30 – 40 kVA Series 0 g General Electric Company 2500 Discovery Blvd. Rockwall, TX 75032 Telephone: (972)-290-7400 Fax: (972)-290-7500 SG Series UPS Technology for the digital world
…
Appliances 30(88 pages) |
AudioSource Subwoofer AS10SWOwner's manual for AudioSource AS10SW Subwoofer AS10SW, 4 |
ASROCK Motherboard 970 Pro3 R2.0970 Pro3 R2.0 Quick installation manual - 96FOFC 970 Pro3 R2.0, 156 |
Sony Car Speakers XS-HT130CNXS-HT130CN Instructions - 5V35R3 XS-HT130CN, 2 |
Transition Networks Media Converter C/TR-CF-01SM#ZRA2IC C/TR-CF-01SM: Transition Networks Media Converter Owner Documentation C/TR-CF-01SM, 4 |
Vista Switch QSW4Switch Instruction manual (Vista QSW4) QSW4, 2 |
Kunbus Control Unit cRIO PBGuide: Kunbus cRIO PB (KM8HPM, Upd.06th Dec 2023) cRIO PB, 11 |
Philips Vacuum Cleaner FC6050Vacuum Cleaner PDF Manual FC6050, 56 |
Omron Controller C200HE-CPU11C200HE-CPU11 (Controller ePDF User Guide, #OUX285) C200HE-CPU11, 241 |
Cabletron Systems Repeater MR-9000TPTOperation & user’s manual for Cabletron Systems MR-9000TPT Repeater MR-9000TPT, 22 |
Immergas Boiler Maior Eolo 24 4EInstallation manual for Immergas Maior Eolo 24 4E Boiler Maior Eolo 24 4E, 30 |
Aerotech Valve Positioners ABL1000WB Series#T3OQ2E ABL1000WB Series: Aerotech Valve Positioners Owner Documentation ABL1000WB Series, 40 |
Yamaha Outboard Motor F150AOutboard Motor Service manual (Yamaha F150A) F150A, 313 |