Manualios.com

COBHAM sailor 6210 Installation Manual

COBHAM sailor 6210 Manual Online:

3.85, 2216 votes
COBHAM sailor 6210 User Manual
COBHAM sailor 6210 User Guide
COBHAM sailor 6210 Online Manual

Text of COBHAM sailor 6210 User Guide:

  • COBHAM sailor 6210, SAILOR 6217 VHF DSC - AIS Receiver System configuration examples Chapter B: System configurations B-41 BBBB System configurations B.1.2 How to install a SAILOR 6205 close to the VHF radio Figure B-2: How to install a SAILOR 6205 close to the VHF radio SAILOR 6201/03 CTRL RX/TX 12VDC SAILOR 6208 Connection box 1 2 3 8 110VAC/230VAC SAILOR N163S Power Supply 24VDC 24VDC Shield/GND -battery Yellow Black Red Pink Grey Brown/Drain Blue CAN_H CAN_L -battery RX+ telephony out RX- telephony out On/off from CSM TX- telephony in TX+ telephony in Oran

  • Cable requirements SAILOR 6248 VHF B-30 Appendix B: System configurations Cable 18 Cable between the connection box and terminals to extend the power supply wires. 4 leads, screened wires of 0.5mm 2 . Supply for 6204 CSM for extended CAN BUS connections. Cable 19 The voltage drop along the cable increases with the length of the cable. Separate supply cables can b

  • COBHAM sailor 6210, Accessories SAILOR 6217 VHF DSC - AIS Receiver 2-26 Chapter 2: Installation 2.7.2 Connection box SAILOR 6207 The SAILOR 6207 Connection Box is used to connect GPS (NMEA), GPS/AIS DSC modem and further SAILOR 6201 Handsets. For wiring and cabling details see System configuration examples on page B-1 . Figure 2-19: SAILOR 6207 Connection Box for parallel handsets, mounting Figure 2-20: Connection Box for parallel handsets, wiring 12 11 10 9 8 7 6 5 4 3 2 1 12 11 10 9 8 7 6 5 4 3 2 1 12 11 10 9 8 7 6 5 4 3 2 1 VHF 62XX Handset 2 Handset 1 99-132868-A J1 J2 J3 Wire color Pin Brown 1 Blue 2 White 3 Green 4 Yellow 5 Grey 6 Pink 7 Red 8 Black 9 10 Orange NMEA in+ NMEA i

  • System configuration examples SAILOR 6248 VHF B-18 Appendix B: System configurations B.1.16 How to install a CAN bus with 3 CSMs in bridge wings Figure B-17: System configuration: CAN bus, 3 SAILOR 6204 CSMs, in bridge wings

  • COBHAM sailor 6210, Returning units for repair SAILOR 6217 VHF DSC - AIS Receiver 4-36 Chapter 4: Service & maintenance 4.3 Returning units for repair Should your Cobham SATCOM product fail, please contact your dealer or installer, or the nearest Cobham SATCOM partner. You will find the partner details on www.cobham.com/satcom where you also find the Cobham SATCOM Self Service Center web-portal, which may help you solve the problem. Your dealer, installer or Cobham SATCOM partner will assist you whether the need is user training, technical support, arranging on-site repair or

  • COBHAM sailor 6210, VHF antenna installation SAILOR 6210 VHF 2-22 Chapter 2: Installation Figure 2-16: Antenna positioning Figure 2-17: Antenna positioning 1/2 RX/TX DSC RX/TX DSC No. 1 VHF No. 2 VHF No. 2 VHF No. 1 VHF 39679 RX/TX DSC RX/TX DSC No. 1 VHF No. 2 VHF No. 2 VHF No. 1 VHF 39679

  • COBHAM sailor 6210, ii SAILOR 6248 VHF Disclaimer Any responsibility or liability for loss or damage in connection with the use of this product and the accompanying documentation is disclaimed by Thrane & Thrane A/S. The information in this manual is provided for information purposes only, is subject to change without notice and may contain errors or inaccuracies. Manuals issued by Thrane & Thrane A/S are periodically revised and updated. Anyone relying on this information should acquire the most current version e.g. from www.cobham.com/satcom, Service and support, or from the distributor. Thrane & Thrane A/S is not responsible for the content or accur

  • COBHAM sailor 6210, SAILOR 6222 VHF DSC Cable requirements Appendix B: System configurations B-27 BBBB System configurations B.2 Cable requirements The following cable information relates to the cable numbers in the system configuration drawings on the previous pages. Cable Part number Description Specification Remarks 1 Antenna cable RG214 or better 2 Handset cable 1 m, spiraled Part of handset 3 TT-37- 131344 Power cable 1.5 m power cable Included in 406222A 4 Not a T&T part 3-wire power cable, shielded Depends on length 24 VDC, 4 A 5 406209-941 5 m cable for SAILOR 6207 Connection Box 10-pole LTW cable with screen Included

  • COBHAM sailor 6210, SAILOR 6248 VHF Cable requirements Appendix B: System configurations B-27 BBBB System configurations Cable 8 (AUX) Part number: 406208-941 SAILOR 6248 VHF AUX connector LTW 12-pin, circular male Signal designation Cable pin 406208- 941 (5 m) SAILOR 6208 Conn. Box In from VHF SAILOR 6208 Conn. Box Out of box SAILOR 6208 Conn. Box Out of box Signal description Ships cable 6 twisted pairs overall screen Pin 1 Shield/GND Brown J1-1 J2-1 J3-1 Equipment ground paired with no. 8 Pin 2 Lo Power Blue J1-2 J2-2 J3-2 Low power forced control. Active when connected to ground paired with no. 3 Pin 3 Not used White J1-3 J2-3 J3-3 Impedan

  • COBHAM sailor 6210, Entering the MMSI number SAILOR 6217 VHF DSC - AIS Receiver 3-32 Chapter 3: First-time power up 3.2 Entering the MMSI number When the VHF radio is powered on for the first time, you must enter the vessel’s MMSI number. Hereafter the MMSI number is briefly displayed after power up. The MMSI is a unique, 9-digit identifier assigned to your ship. Entering the MMSI number When being prompted after power up enter the MMSI number as described below: 1. Enter the 9 digits one by one by turning the selector wheel knob to the desired digit, press the

  • COBHAM sailor 6210, iv SAILOR 6222 VHF DSC Preface Radio for occupational use The SAILOR 6222 VHF DSC meets the requirements of the SOLAS and is intended for use in a maritime environment. SAILOR 6222 VHF DSC is designed for occupational use only and must be operated by licensed personnel only. SAILOR 6222 VHF DSC is not intended for use in an uncontrolled environment by general public. SAILOR 6222 VHF DSC is designed for installation by a skilled service person. Training information The SAILOR 6222 VHF DSC is designed for occupational use only and is also classified as such. It must be operated by licensed personnel only. It must only be used in the

  • COBHAM sailor 6210, Accessories SAILOR 6222 VHF DSC 2-22 Chapter 2: Installation 2.5.2 Connection box SAILOR 6207 The SAILOR 6207 Connection Box is used to connect GPS (NMEA), GPS/AIS DSC modem and further SAILOR 6201 Handsets. For wiring and cabling details see System configuration examples on page B-1 and How to install LAN on page B-24. Figure 2-15: SAILOR 6207 Connection Box for parallel handsets, mounting Figure 2-16: SAILOR 6207 Connection Box for parallel handsets, wiring 12 11 10 9 8 7 6 5 4 3 2 1 12 11 10 9 8 7 6 5 4 3 2 1 12 11 10 9 8 7 6 5 4 3 2 1 VHF 62XX Handset 2 Handset 1 99-132868-A J1 J2 J3 Wire color Pin Brown 1 Blue 2 White 3

  • COBHAM sailor 6210, 4-33 Chapter 4 4444 Service & maintenance Service & maintenance 4 4.1 Contact for support Contact your authorized dealer for technical service and support of the VHF radio. Before contacting your authorized dealer you can go through the troubleshooting guide to solve some of the most common operational problems. 4.2 Maintenance 4.2.1 Preventive maintenance Maintenance of the SAILOR 6210 VHF can be reduced to a maintenance check at each visit of the service staff. Inspect the radio for mechanical damages, salt deposits, corrosion and any foreign material. Due to its robust construction and ruggedness the radio has a long lifetime. Anyway it must carefully be checked at

  • COBHAM sailor 6210, SAILOR 6248 VHF Connectors Chapter 2: Installation 2-11 2222 Installation 2.3.2 Connectors at the rear panel Figure 2-11: Connections at the rear panel 4 1 2 3 5 6 7 l 1. ACC connector for accessories 2. AUX connector for VDR, external speaker 3. Power connector PWR FUSE with fuse 10 A mini ATO 4. Ground stud for grounding 5. ANT connector for VHF antenna 6. CTRL connector 7. Ethernet connector: LAN

  • COBHAM sailor 6210, Table A-1: Technical specifications, part 1 Item Specification Weight SAILOR 6248 VHF < 1.50 kg (3.3 lbs) approximately Box weight SAILOR 6248 VHF 3.8 kg (8.4 lbs) approximately, including SAILOR 6201 Handset and wall mount cradle, SAILOR 6090 Power Converter and Installation and user manual in box. Dimensions Height: Outer dimension 107 mm, hole height for flush mount 89 mm Width: Outer dimension 241 mm, hole width for flush mount 227 mm Depth: Outer dimension from front of knobs 132 mm, de

  • COBHAM sailor 6210, SAILOR 6249 VHF Survival Craft Connectors Chapter 2: Installation 2-11 2222 Installation 2.3.3 ACC connector Use the connector marked ACC to connect a SAILOR 6201 Handset. You may also connect a waterproof SAILOR 6203 Handset or SAILOR 6202 Handmicrophone. Connector type: Circular connector, 10-pin, male. 1 2 3 4 10 5 6 7 8 9 Panel lock, 10 pin male Connection cable with plug, part number 406209-941. Pin assignment: Connector front view on the VHF radio. Table 2-3: Pin allocation, ACC connector Pin Description Wire color 1 Brown 2 Blue 3 White 4 Green 5 Mike 2 / Line in Yellow 6 EAR 2 / Line out Grey 7 Hook_PTT Pink 8 Battery supply when radio is on Red 9 Internal GND = - Batte

  • COBHAM sailor 6210, System configuration examples SAILOR 6217 VHF DSC - AIS Receiver B-42 Chapter B: System configurations B.1.3 How to install a SAILOR 6205 very close to the VHF radio Figure B-3: How to install a SAILOR 6205 very close to the VHF radio SAILOR 6201/03 CTRL RX/TX 12VDC 1 2 110VAC/230VAC SAILOR N163S Power Supply 24VDC 24VDC 15 SAILOR 6205 Control Speaker Microphone (With DSC) SAILOR 6215/16/17 VHF 5m SAILOR 6202 3 Place jumper so power supply always is switched on Screen/ground -Vin +Vin Ground -Vout (Black) +Vout (Red) NC 10 10 10 NC 2

  • COBHAM sailor 6210, SAILOR 6215/6216 VHF DSC Maintenance Chapter 4: Service & maintenance 4-35 4444 Service & maintenance DSC routine testing Check the DSC function regularly. Verify the complete DSC installation, with antennas, by transmitting a Safety Test call to another station (coast or ship). The test call is generated using the DSC call flow via menu CALL. The call should normally be replied by the receiving station without questioning. The default configuration of a DSC VHF radio is auto- acknowledgement of any received Safety test call requests. If a ship is equipped with mul

  • Power, VHF antenna and external equipment SAILOR 6215/6216 VHF DSC 2-16 Chapter 2: Installation 2.3.1 ACC connector Use the connector marked ACC to connect GPS input. The interface for GPS is NMEA 0183 (EN61162-1)/NMEA. Connector type: Circular connector, 10-pin. Connection cable with plug, part number 406209-941. Pin assignment: Connector front view on the VHF radio. P

  • COBHAM sailor 6210, Installing the VHF radio SAILOR 6210 VHF 2-10 Chapter 2: Installation Mounting with U mounting bracket To mount the VHF radio as tabletop, do as follows: 1. Find a suitable location for the VHF radio. Check that the space is wide/deep enough to accommodate the VHF radio. 2. Fasten the bracket with 4 screws (included in the delivery.) 3. Insert the VHF radio in the bracket and fasten it with the two knobs. 4. The display of the VHF radio should be at an angle of approximately 90° to your line of sight when operating it. Figure 2-3: Mounting with U mounting bracket

  • COBHAM sailor 6210, SAILOR 6222 VHF DSC Troubleshooting guide Chapter 4: Service & maintenance 4-3 4444 Service & maintenance 4.3 Troubleshooting guide Action Symptom Remedy The radio will not turn on The display is empty. Check if power is present. Check fuse which is placed in the power connector. Check performance of power supply if connected to one. No commu- nication The loud- speaker is mute. Check the antenna installation. Check antenna cable. Check handset/Handmicrophone and cable. GPS Position requested. Check the GPS input - see the Installation gui

  • COBHAM sailor 6210, SAILOR 6217 VHF DSC - AIS Receiver Cable requirements Chapter B: System configurations B-47 BBBB System configurations The voltage drop along the cable increases with the length of the cable. Separate supply cables can be installed in parallel with the CAN cable to reduce voltage drop in long cables. The maximum allowed voltage drop from VHF to CSM is 2 VDC. It means 1 VDC forward and 1 VDC return. Max current consumption for each CSM is 0.5A. Formula to calculate DC resistance in a wire: L = length of wire one way, in metre a = cross section of the wire in mm² Contact your local dealer for further informat

  • SAILOR 6217 VHF DSC - AIS Receiver System configuration examples Chapter B: System configurations B-43 BBBB System configurations B.1.4 How to install an AIS chart plotter to 6217 Figure B-4: How to install an AIS chart plotter SAILOR 6201/03 ACC RX/TX 12VDC 1 2 110VAC/230VAC SAILOR N163S Power Supply 24VDC 24VDC SAILOR 6217 VHF DSC – AIS Receiver 5m SAILOR 6202 3 10 10 2 6-27-2012 Chart pl

  • COBHAM sailor 6210, VHF antenna installation SAILOR 6248 VHF 2-18 Chapter 2: Installation 2.4.2 VHF RX/TX antenna In installations with two or more VHF radios it is important to ensure the optimum performance of these by carefully selecting the antenna positions for both radios. It is recommended to maximize the RF attenuation between the VHF RX/TX antennas in the installation. You can ensure this by not having the RX/TX antennas positioned at the same horizontal level, i.e. the RX/TX antennas for each radio must be installed at shifted elevations as shown in the following drawing. If sufficient vertical d

  • COBHAM sailor 6210, VHF radio with DSC SAILOR 6215/6216 VHF DSC 1-2 Chapter 1: Introduction Controls on the front plate 1. Loudspeaker. 2. Four soft keys with function title in the display. 3. Quick selection key for channel 16 and the programmed call channel. 4. Large display. 5. Connector for Handmicrophone or handset. If not used, put the cap from the ACC connector on the front connector to prevent water ingress. 6. Button for sending a DSC Distress alert. 7. Squelch control to mute background noise. 8. Replay button to play back u

  • SAILOR 6215/6216 VHF DSC System setup Chapter 2: Installation 2-23 2222 Installation 2.5 System setup To change a setting in the SYSTEM SETUP, do as follows: 1. Press the soft key SETUP. If it is not in the display, press the soft key MORE until SETUP appears. 2. Press the arrow soft key or to advance to SYSTEM SETUP. 3. Turn the selector wheel knob to go to a setting, then press the sele

Related Products and Documents (Radio):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 HP 3390 - LaserJet All-in-One B/W Laser Getting started manual hp/3390-laserjet-all-in-one-b-w-laser-Z15.pdf 02 Jul 2022 36 1.4 Mb
2 CyberResearch COML 2232F Operation & user’s manual cyberresearch/coml-2232f-4L1.pdf 05 Oct 2023 20 0.24 Mb
3 Makita BO6040 Instruction manual makita/bo6040-2AB.pdf 11 Sep 2022 36
4 Miller HDC 1500DX Owner's manual miller/hdc-1500dx-71Z.pdf 13 Sep 2022 44
5 Dodge 2014 Dart Operation & user’s manual dodge/2014-dart-86F.pdf 16 Dec 2023 140
6 Kettler Ergoracer GT Brochure kettler/ergoracer-gt-53D.pdf 02 Aug 2022 1

Similar Resources:

  • THOMSON

    DPL907U

    (7 pages)
    Type of set:Type d'appareil:Geräteart:Tipo d'apparecchio:Tipo de aparato:Power supply:Alimentation:Stromversorgung:Alimentazione:Alimentación:FM - MF:MW - PO:FM - MF:MW - PO:Frequency response:Courbe de réponse:Frequenzgang:Curva di risposta:Curva de respuesta:Total harmonic distorsion:Distorsion harmonique:Klirrfaktor:Distorsione armonica:Disto …
  • Panasonic

    RCDC1 - IPOD/IPHONE ALARM CLOCK

    (48 pages)
    Operating InstructionsManuel d’utilisationInstrucciones de funcionamientoClock RadioRadio-réveilRadio RelojModel No. / Modèle / No de modelo RC-DC1RQTX1207-YIf you have any questions contactIn the U.S.A and Puerto Rico:1-800-211-PANA (7262)In Canada:1-800-561-5505Pour toute demande de renseignements, appeler au1-800-561-5505As an ENERGY STAR® Partner, …
  • Philips

    AE6580

    (2 pages)
    PhilipsPortable Radiopocket sizeStereo earphoneAE6580Portable radio on the goThis super-compact pocket-size Philips FM/MW portable radio is supplied with stereo in-earphones cable winder, making this the ideal radio on the go.Enjoy your favorite stations• FM/MW analogue radio tuningEasy to use• Headphone jack for better personal music enjoyment• Pock …
  • Fisher-Price

    72777

    (8 pages)
    ®Chatter RadioTMInstructionsProduct Number: 72777Please save these instructions for future reference.Adult assembly is required to install batteries.Tool needed to install batteries: Phillips ScrewdriverThis product requires three, size “AA” batteries (included). …
  • Motorola

    RADIUS GM300

    (2 pages)
    Operating Instructions for the MotorolaRadius® GM300 8-Channel, Conventional FM Radio To turn the radio on Turn the ON/OFF VOLUME knob to the right until it clicks. The LED lights will show the last sta-tus of the radio, and a start-up tone will be heard. To receive Set the volume by turning the ON/OFF VOLUME knob clockwise. Select the channel by pressing …
  • Kobian

    IXA321i

    (45 pages)
    Subject Operational Notes..........................................................3 Player overview.............................................................5 Accessories....................................................................8 LCD...............................................................................9 Turning the power on/off....... …

Comments, Questions and Opinions: