Manualios.com

Alcorn Mcbride Digital Binloop HD Operation & User’s Manual

  • Digital Binloop HD Car Video System
  • ma3lQ9Hb4yXAU
  • Operation & User’s Manual
  • PDF / Adobe Acrobat Reader
  • 137

Alcorn Mcbride Digital Binloop HD Manual Online:

4.4, 663 votes
Alcorn Mcbride Digital Binloop HD User Manual
Alcorn Mcbride Digital Binloop HD User Guide
Alcorn Mcbride Digital Binloop HD Online Manual

Text of Alcorn Mcbride Digital Binloop HD User Guide:

  • Alcorn Mcbride Digital Binloop HD, Alcorn McBride Binloop User’s Manual Page 29 Get/Set SMPTE Start time Description: This command will get or set the SMPTE start time. Parameters: hh = hours mm = minutes ss = seconds ff = frames Get Command: RT Response: hh:mm:ss.ff Example: Command: RT Response: 00:00:01.00 Set Command: hh:mm:ss.ffRT Response: R Example: Command: 00:00:01.00RT Response: R Get/Set SMPTE End time Description: This command will get or set the SMPTE end time. Parameters: hh = hours mm =

  • Alcorn Mcbride Digital Binloop HD, Alcorn McBride Binloop User’s Manual Page 61 Download Configuration … Note: If the optional CobraNet card is installed, please disconnect the CobraNet interface before downloading the CobraNet configuration otherwise it may fail. This option allows you to download the configuration you are currently viewing. This includes all of the SMPTE interfaces settings, unit configuration settings, as well as any programmed timecode triggers. A confirmation window will appear. Upload Configura

  • Alcorn Mcbride Digital Binloop HD, Alcorn McBride Binloop User’s Manual Page 67 CobraNet Description CobraNet is an industry standard interface for distributing multiple channels of audio over an Ethernet based network. This is useful for both transmitting audio over long distances, as well as easily interfacing to CobraNet compatible systems using a simple Ethernet cable rather than many individual analog connections. Details CobraNet is digitally encoded audio over Ethernet, and as such it does not suffer the effects of long distance analog transmission issues. It is not within the scope of this manual to provide a detail

  • Alcorn Mcbride Digital Binloop HD, Alcorn McBride Binloop User’s Manual Page 65 Segment This is the number of the video clip that you want to play (for Play triggers). Offset This field is used for reproducers that support playback from a specified offset into a video or audio file. The Digital Binloop HD does not support this feature. Stereo or Mono versus Independent For Binloops that support audio playback, this option is used to trigger independent audio playback on the left or right channel. The Digital Binloop HD does not support this type of audio playback, so leave this settin

  • Alcorn Mcbride Digital Binloop HD, Alcorn McBride Binloop User’s Manual Page 50 If you intend to communicate with RS-232, you must select the Serial option and specify the COM port in your PC that is connected with the Binloop. If you are using Ethernet, you must select Ethernet as the communication method and then enter the Binloop’s IP address in the provided box. Once you have setup the appropriate connection, click the OK button to close this window. To make sure that the connection is working properly, click on the icon at the top of the Bi

  • Alcorn Mcbride Digital Binloop HD, Alcorn McBride Binloop User’s Manual Page 121 Appendix C - Updating Firmware The various components of the Binloop are all capable of accepting firmware updates. The following guides will instruct you on how to update the firmware of each component. Reproducer Card Firmware The ReproHD High-Definition Video Reproducers within the Binloop can be updated by copying a firmware update file to a Compact Flash card and inserting that card into the Reproducer’s CF socket. These step-by-step instructions will walk you through this process:

  • Alcorn Mcbride Digital Binloop HD, Alcorn McBride Binloop User’s Manual Page 25 Get/Set Subnet Mask number Description: This command will get or set the number used to isolate the subnet. Parameters: xxx.xxx.xxx.xxx is a standard IPv4 subnet mask. Get Command: SM Response: xxx.xxx.xxx.xxx Example: Command: SM Response: 255.255.255.0 Set Command: xxx.xxx.xxx.xxxSM Response: R Example: Command: 255.255.255.0SM Response: R Get/Set Gateway address Description: This command will get or set the IP address of the network gateway. Parameters: xxx.xxx.xxx.xxx is a standard IPv4 IP gateway

  • Alcorn Mcbride Digital Binloop HD, Alcorn McBride Binloop User’s Manual Page 68 Note: the second, slave CobraNet interface for reproducers 9-16 must be connected to the same CobraNet network as the first, master CobraNet interface for reproducers 1-8 for proper operation. Reproducer Configuration

  • Alcorn Mcbride Digital Binloop HD, Alcorn McBride Binloop User’s Manual Page 10 How the Binloop Works Now that you’re more familiar with the various hardware components that comprise the Binloop, let’s get more familiar with how those components actually work together. The diagram below outlines the different components we’ve covered as well as their functional relationship with one another. The sections that follow will cover the various systems you see in this diagram, so please use it as a visual reference.

  • Alcorn Mcbride Digital Binloop HD, Alcorn McBride Binloop User’s Manual Page 86 File Naming A specific file naming convention is used so that the Digital Binloop HD can identify the file type, as well as associate the file with a number. Here is a table that shows the naming conventions based on the type of file that is being named: File Type File Naming Style MPEG2 Video Elementary Stream VIDnnnnn.M2V H.264 Video Elementary Stream VIDnnnnn.H264 VC-1 Video Elementary Stream VIDnnnnn.VC1 MPEG Transport Stream VIDnnnnn.MPG As you can see from this table, the files are identified based on the file extension. For example, the Binloop will identi

  • Alcorn McBride Binloop User’s Manual Page 74 Control Buttons Directly beneath the Unit Status LED's, there are four control buttons. Their functions are defined briefly here but they will be discussed in more detail over the course of the next two chapters: Start - If the Binloop is programmed to generate SMPTE, pushing this button start

  • Alcorn McBride Binloop User’s Manual Page 106 Before modifying the new script, click on File  Save to give it a descriptive name and store a copy of the script on your PC. For this example, we will save our script as Interactivator-blHD. Port Configuration Next, we need to tell WinScript that a Digital Binloop HD is connected to Port 1 of the show controller. Cl

  • Alcorn Mcbride Digital Binloop HD, Alcorn McBride Binloop User’s Manual Page 60 You can assign a Reproducer to be a member of more than one Group. Below is a screenshot showing the Group assignment window. This example assigns Reproducers 5, 6, 7, and 8 to be members of Group 1. Status… You can determine that current playing status of each Reproducer by opening the Status window. When this window opens, select Refresh and after a brief moment each Reproducer will report their current status. A timeout message appears i

  • Alcorn Mcbride Digital Binloop HD, Alcorn McBride Binloop User’s Manual Page 113 Configuring the Network Settings of the Binloop This application note requires your Binloop is configured for the factory default network settings, which are as follows: IP Address 192.168.0.254 Subnet Mask 255.255.255.0 Gateway 192.168.0.1 If you believe that these settings may have been altered, you should verify them using the front-panel menu wheel interface of the Binloop. Browse to the Network Setup screen and make sure that all of th

  • Alcorn Mcbride Digital Binloop HD, Alcorn McBride Binloop User’s Manual Page 108 Your script should look like this. Now, the PlayClip sequence will be triggered when Button #1 on the front of the controller is pushed. Editing the PlayFile Sequence At this point, the PlayClip sequence is empty, so nothing will happen when it is activated. That means that the next step is to add events in the PlayClip sequence so that it commands the Binloop to play a file. To access the event list for the PlayClip sequence, right-click on PlayClip and select Edit Sequence Events. You can also double-click the sequence number on the left-hand side (i.e. 002

  • Alcorn Mcbride Digital Binloop HD, Alcorn McBride Binloop User’s Manual Page iii Document Revision 1.4 September 22, 2010 Copyright  1996-2010 Alcorn McBride, Inc. All rights reserved. Every effort has been made to assure the accuracy of the information contained in this manual, and the reliability of the Alcorn McBride Digital Binloop HD hardware and software. Errors can sometimes go undetected, however. If you find one, please bring it to our attention so that we can correct it for others. Alcorn McBride welcomes comments and suggestions on the content and layout of its documentation. Applications described herein are for illustrative purposes only. Alcorn McBride Inc. ass

  • Alcorn Mcbride Digital Binloop HD, Alcorn McBride Binloop User’s Manual Page 117 Appendix A - Troubleshooting Guides Card Cage Troubleshooting Guide Symptom Cause(s) Solution(s) 1) No Front Panel display or LEDs a) No Power b) Bad Power Supply a) Check Power connections b) Cycle Power 2) One or more of the reproducers not responding to test button press. a) Incompatible Video File b) Faulty Button c) Faulty Reproducer d) Faulty Controller a) Press Reproducer Test Button to see if reproducer responds. b) Press Mute Button and make sure Reproducer LED’s illuminate RED. (This verifies communication) c) Cycle Power Video Troubleshooting Guide Symptom Cause(s) Solution(s) 1) N

  • Alcorn Mcbride Digital Binloop HD, Alcorn McBride Binloop User’s Manual Page 42 MIDI Show Control Protocol The MIDI Show Control protocol is primarily used when controlling the Binloop over its dedicated MIDI port. However, it is also available as one of the configurable protocols available on the RS-232 Show Control port. If your intention is to control the Binloop with a non-MIDI based system, you should consider using the Pioneer/AMI protocol instead. It should be noted that MIDI Show Control is a very wide-ranging protocol used for many different application

  • Alcorn Mcbride Digital Binloop HD, Alcorn McBride Binloop User’s Manual Page 91 File System Limitation – 4GB File Size If the File Splitter software is no longer available, please obtain the latest manual from the Alcorn McBride website, or contact technical support for the latest recommended method for splitting files. The Binloop HD uses the FAT32 file system to store files on its Compact Flash cards. This file system is widely used, and will allow your flash cards to be accessible from any Windows based PC or MAC computer. Although the supported volume size of Compact Flash cards is much larger, the maximum file size supported

  • Alcorn McBride Binloop User’s Manual Page 51 Controlling the Binloop with the Binloop Software Note: Please refer to the Media section of this manual for more information on creating your own videos and file naming conventions for the Binloop. Now that you are connected to the Binloop using the Binloop Software, let’s go through an example of how you can use

  • Alcorn McBride Binloop User’s Manual Page 69 CobraNet Configuration Detection – The configuration process starts by locating the CobraNet hardware. Upon locating the CobraNet interface the hardware will report back the revision number for identification purposes. A Note about Downloading the CobraNet configuration – When downloading the CobraN

  • Alcorn McBride Binloop User’s Manual Page 24 Get/Set Unit ID Description: This command will get or set the unit ID number. Parameters: xx represents a decimal number between 1 – 49. Set Command: xxID Response: R Example: Command: 1ID Response R Get Command: ID Response: xx Example: Command: ID Response: 1 Get/Se

  • Alcorn Mcbride Digital Binloop HD, Alcorn McBride Binloop User’s Manual Page 73 Hardware Description Controls and Indicators The Binloop is normally controlled either internally using a configuration loaded from our Binloop software, or remotely from an external control system. However, the product does have several controls and status indicators located on the front panel. Unit Status LED’s On the front of the Binloop are nine LED's corresponding to the status of the unit. Below is a brief description of their meaning: Power (Green) - Power is be

  • Alcorn Mcbride Digital Binloop HD, Alcorn McBride Binloop User’s Manual Page 70 CobraNet Advanced Configuration CobraNet Clip - IP Address – This is the network address, which is used to identify the source of the session. The function of this address is the same as any other IP address used on the network Resolution – This is the encoded resolution of the audio source. 20 or 24 bits are the standard options Latency – This option allows the operator to set the maximum delay tolerated in the communications channel Conductor Priority – This establishes the point of control for the communications session. Bundle Assignments

Related Products and Documents (Car Video System):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 BMW X5 2002 Owner's manual bmw/x5-2002-D4U.pdf 20 Dec 2022 185 2.92 Mb
2 Sony PCWA-C800S - Wireless Lan Router Troubleshooting manual sony/pcwa-c800s-wireless-lan-router-K65.pdf 05 Jul 2022 2 0.19 Mb
3 LG LMN090HE Specifications lg/lmn090he-N36.pdf 08 Feb 2023 1
4 NEC NEC NP64 User's manual supplement nec/nec-np64-9LW.pdf 23 Dec 2023 16
5 Sony Ericsson W395 Working instruction, mechanical sony-ericsson/w395-5WN.pdf 22 Jan 2024 59
6 Eden World Tour 1205 Operation manual eden/world-tour-1205-T8Q.pdf 16 Jul 2022 21 0.07 Mb

Similar Resources:

  • Boss Audio Systems

    648UA

    (5 pages)
    iPod® is a trademark of Apple, Inc.registered in the U.S. and other countries.Boss Audio Systems is not affiliated with Apple, Inc.User’s Manual648UAIN-DASH SINGLE-DINMP3-COMPATIBLE CDAM/FM RECEIVERWITH USB AND SD MEMORY CARD PORTSAND FRONT PANEL AUX INPUTBOSS Audio Systems-VOBS$PVSUt0YOBSE$"www.bossaud …
  • Pyle

    PLCM103

    (2 pages)
    H T T P : / / W W W . P Y L E A U D I O . C O MInstruction Manual1 x Remote control1 x Instruction manual1 x CablesAccessoriesPLCM10310.2" Selectable Size 4.5'' or 5.6'' or 7'' or 8.5'' Rearview Mirror Monitor with LicensePlate Mount Rear View Camera w/ Night VisionSpecificationMONITOR* Selectable Display Sizes: 1 …
  • v.link

    VL2-PCM31

    (25 pages)
    Version 14.06..2018 HW: LVDS …….VL2-PCM31 v.LiNK Video-inserter VL2-PCM31 Compatible with PORSCHE vehicles with PCM 3.1 infotainment Video-inserter with 2 video inputs and 1 rear-view camera input with CAN control Product features  Video-inserter for factory-infotainment systems  2 video-inputs for after-market devices (e.g. DVD-Play …
  • Sony

    XS-L1536 - Subwoofer

    (1 pages)
    3-239-563-11 (1)XS-L1536Sony Corporation © 2002 Printed in ChinaThiele/Small parametersParamètres de Thiele-SmallRecommended Enclosure : Sealed typeBoîtier recommandé : de type scelléAlojamiento recomendado: Sellado推薦箱體:封閉型Impedance , Impédance ,Impedancia , 阻抗4Ωd (mm) 340d (inch) 13.4Rdc (Ω) 3.2Fs (Hz) 23.0Qts 0.42Qes 0.46Qms 5 …
  • Rosen

    DVA-3210

    (25 pages)
    Warning!THE DVA-3210 DVD/CD/MP3 PLAYER IS DESIGNED TOENABLE VIEWING OF DVD OR CD-VIDEO RECORDINGS ONLYFOR REAR-SEAT OCCUPANTS.MOBILE VIDEO PRODUCTS ARE NOT INTENDED FOR VIEW-ING BY THE DRIVER WHILE THE VEHICLE IS IN MOTION.SUCH USE MAY DISTRACT THE DRIVER OR INTERFERE WITHTHE DRIVER’S SAFE OPERATION OF THE VEHICLE, ANDTHUS RESULT IN SERIOUS INJURY OR DEATH …
  • Chevrolet

    Corvette 2015

    (16 pages)
    Review this Quick Reference Guide for an overview of some important features in your Chevrolet Corvette. More detailed information can be found in your Owner Manual. Some optional equipment described in this guide may not be included in your vehicle. For easy reference, keep this guide with your Owner Manual in your glove box. www.chevrolet.com …

Comments, Questions and Opinions: