Manualios.com

Alfa Network AWAP602HW Operation & User’s Manual

Alfa Network AWAP602HW Manual Online:

3.45, 2314 votes
Alfa Network AWAP602HW User Manual
Alfa Network AWAP602HW User Guide
Alfa Network AWAP602HW Online Manual

Text of Alfa Network AWAP602HW User Guide:

  • Alfa Network AWAP602HW, Screen snapshot – LAN Interface Setup Item Description IP Address Fill in the IP address of LAN interfaces of this WLAN Access Point. Subnet Mask Fill in the subnet mask of LAN interfaces of this WLAN Access Point. Default Gateway Fill in the default gateway for LAN interfaces out going data packets. DHCP Click to select Disabled, Client or Server in different operation mode of wireless Access Point. DHCP Client Range Fill in the start IP address and end IP address to allocate a range of IP addresses; client with DHCP function set will be assigned an IP address from the range. Show Client Click to open the A

  • Alfa Network AWAP602HW, recover the previous configuration setting. 2.3.8 WDS Settings Wireless Distribution System uses wireless media to communicate with other APs, like the Ethernet does. To do this, you must set these APs in the same channel and set MAC address of other AP that you want to communicate with in the table and then enable the WDS. Screen snapshot – WDS Setup Item Description Enable WDS Click the check box to enable wireless distribution system. Refer to 4.21 What is Wireless Distribution System (WDS)? MAC Address Fill in the MAC address of AP to register the wireless distribution system access capability. Comment Fill in the comment tag for the r

  • Use of such filters can be helpful in securing or restricting your local network. Screen snapshot – Firewall - IP Filtering Item Description Enable IP Filtering Click to enable the IP filtering security function. Local IP Address Protocol Comments To restrict data transmission from local network on certain IP addresses, fill in the IP address and the protoco

  • Alfa Network AWAP602HW, LAN interface, WAN interface, Wireless interface, NAT and Firewall modules are applied to this mode Bridge Each interface (LAN, WAN and Wireless) regards as bridge. NAT, Firewall and all router’s functions are not supported Wireless ISP Switch Wireless interface to WAN port and all Ethernet ports in bridge mode. Wireless interface can do all router’s functions Apply Changes Click the Apply Changes button to complete the new configuration setting. Reset Click the Reset button to abo

  • Alfa Network AWAP602HW, Screen snapshot – Management – Denial-of-Service Item Description Enable DoS Prevention Click the checkbox to enable DoS prevention. Whole System Flood / Per-Source IP Flood… Enable and setup prevention in details. Select ALL Click the checkbox to enable all prevention items. Clear ALL Click the checkbox to disable all prevention items. Apply Changes Click the Apply Changes button to save above settings.

  • Alfa Network AWAP602HW, 6. Select TCP/IP and click the properties button on the Network dialog box. 7. Select Specify an IP address and type in values as following example. 9 IP Address: 192.168.1.1, any IP address within 192.168.1.1 to 192.168.1.253 is good to connect the Wireless LAN Access Point. 9 IP Subnet Mask: 255.255.255.0 8. Click OK to complete the IP parameters setting. 2.2 Connect to the WLAN Broadband Router Open a WEB browser, i.e. Microsoft Internet Explore, then enter 192.168.1.254 on the URL to connect the WLAN Broadban

  • Alfa Network AWAP602HW, Screen snapshot – Operation Mode z Time Zone Setting This page is used to enable and configure NTP client Screen snapshot – Time Zone Settings z LAN Interface Setup This page is used to configure local area network IP address and subnet mask

  • Alfa Network AWAP602HW, Screen snapshot – Management – DDNS Item Description Enable DDNS Click the checkbox to enable DDNS service. Refer to 4.25 What is DDNS? Service Provider Click the drop down menu to pickup the right provider. Domain Name To configure the Domain Name. User Name/Email Configure User Name, Email. Password/Key Configure Password, Key. Apply Change Click the Apply Changes button to save the enable DDNS service. Reset Click the Reset button to abort change and recover the previous configuration setting. 2.3.21 Management - Time Zone Setting This page is used to configure NTP client to get current time.

  • Alfa Network AWAP602HW, Screen snapshot – Management – Time Zone Settings Item Description Current Time It shows the current time. Time Zone Select Click the time zone in your country. Enable NTP client update Click the checkbox to enable NTP client update. Refer to 4.26 What is NTP Client? NTP Server Click select default or input NTP server IP address. Apply Change Click the Apply Changes button to save and enable NTP client service. Reset Click the Reset button to abort change and recover the previous configuration setting. Refresh Click the refresh the current time shown on the screen. 2.3.22 Management – Denial-of-Service This page is used to enable a

  • Alfa Network AWAP602HW, 2.3.14 Firewall - MAC Filtering Entries in this table are used to restrict certain types of data packets from your local network to Internet through the Gateway. Use of such filters can be helpful in securing or restricting your local network. Screen snapshot – Firewall - MAC Filtering Item Description Enable MAC Filtering Click to enable the MAC filtering security function. MAC Address Comments To restrict data transmission from local network on certain MAC addresses, fill in

  • Alfa Network AWAP602HW, Screen snapshot – WDS AP Table Item Description MAC Address It shows the MAC Address within WDS. Tx Packets It shows the statistic count of sent packets on the wireless LAN interface. Tx Errors It shows the statistic count of error sent packets on the Wireless LAN interface. Rx Packets It shows the statistic count of received packets on the wireless LAN interface. Tx Rare (Mbps) It shows the wireless link rate within WDS. Refresh Click to refresh the statistic counters on the screen. Close Click to close the current window. 2.3.9 Site Survey This page is used to view or configure other APs near yours.

  • Alfa Network AWAP602HW, settings. Reset Click the Reset button to abort change and recover the previous configuration setting. Delete Selected Click to delete the selected URL address that will be removed from the URL Filtering list. Delete All Click to delete all the registered entries from the URL Filtering list. Reset Click the Reset button to abort change and recover the previous configuration setting. 2.3.17 Firewall - DMZ A Demilitarized Zone is used to provide Internet services without sacrificing unauthorized access to its local private network. Typically, the DMZ host contains devices accessible to Internet traffic,

  • Alfa Network AWAP602HW, Attain IP Protocol It shows how the WLAN Broadband Router gets the IP address. The IP address can be set manually to a fixed one or set dynamically by DHCP server or attain IP by PPPoE / PPTP connection. IP Address It shows the IP address of WAN interface of WLAN Broadband Router. Subnet Mask It shows the IP subnet mask of WAN interface of WLAN Broadband Router. Default Gateway It shows the default gateway setting for WAN interface outgoing data packets. DNS1/DNS2/DNS3 It shows the DNS server information. MAC Address It shows the MAC address of WAN interface

  • Alfa Network AWAP602HW, Screen snapshot – WAN Interface Setup – PPPoE Item Description PPPoE Click to select PPPoE support on WAN interface. There are user name, password, connection type and idle time settings need to be done. User Name If you select the PPPoE support on WAN interface, fill in the user name and password to login the PPPoE server. Password If you select the PPPoE support on WAN interface, fill in the user name and password to login the PPPoE server. Service Name Fill in the service name of Service Name. The default value is empty. Connection Type Select the connection type from pull-down menu. There are Continuo

  • 2.3.23 Management - Log This page is used to configure the remote log server and shown the current log. Screen snapshot – Management – Log Item Description Enable Log System all Wirelessy DoS Click the checkbox to enable log. Show all log of wireless broadband router Only show wireless log Only show Denial-of-Service log Enable Remote Log Log

  • Alfa Network AWAP602HW, 2.3.18 VPN Setting This page is used to show VPN connection table, configure IPSEC VPN, NAT Traversal, Generate RSA Key, Show RSA Public Key. Screen snapshot – VPN Setup Item Description Enable IPSEC VPN Click to enable IPSEC VPN function. Refer to 4.27 What is VPN? and 4.28 What is IPSEC? Enable NAT Traversal Click to enable NAT Traversal function. Generate RSA Key Click to generate RSA key. Show RSA Public Key Click to show RSA public key that we generate. Apply Changes Click the Apply Changes button to enable IPSEC VPN, NAT Traversal settings. Current VPN Connection Table It shows current WAN interface info

  • z Wireless Security Setup This page is used to configure wireless security Screen snapshot – Wireless Security Setup 2.3.3 Operation Mode This page is used to configure which mode wireless broadband router acts Screen snapshot – Operation Mode Item Description Gateway Traditional gateway configuration. It always connects internet via ADSL/Cable Modem.

  • Alfa Network AWAP602HW, 2 Software configuration There are web based management and configuration functions allowing you to have the jobs done easily. The WLAN Broadband Router is delivered with the following factory default parameters on the Ethernet LAN interfaces. Default IP Address: 192.168.1.250 Default IP subnet mask: 255.255.255.0 WEB login User Name: admin WEB login Password: 12345 2.1 Prepare your PC to configure the WLAN Broadband Router For OS of Microsoft Windows 95/ 98/ Me: 1. Click the Start button and select Settings, then click Control Panel. The Control Panel window will appear. Note: Windows M

  • Alfa Network AWAP602HW, Authentication Key Fill in authentication key. [Manual mode only] Apply Change Click the Apply Changes button to save current tunnel settings. Reset Click the Reset button to abort change and recover the previous configuration setting. Refresh It shows the current connection status. [Manual mode only] Back It returns back to VPN Setup page. z Advanced IKE Setup Screen snapshot – Advanced VPN Settings for IKE Item Description Phase 1

  • Screen snapshot – Wireless Site Survey Item Description SSID It shows the SSID of AP. BSSID It shows BSSID of AP. Channel It show the current channel of AP occupied. Type It show which type AP acts. Encrypt It shows the encryption status. Signal It shows the power level of current AP. Select Click to select AP or client you’d like t

  • Alfa Network AWAP602HW, File configuration files then click the Upload button to update the selected configuration to the WLAN Broadband Router. Reset Settings to Default Click the Reset button to reset the configuration parameter to factory defaults. 2.3.26 Management - Password Setup This page is used to set the account to access the web server of Access Point. Empty user name and password will disable the protection. + Screen snapshot – Management - Password Setup Item Description User Name Fill in the user name for web management login control. New Password Fill in the password for web management login control. Confirmed Password Becau

  • WPA2(AES) or None Show Statistics It shows the TX, RX packets, rate statistics Delete Selected Click to delete the selected clients that will be removed from the wireless distribution system. Delete All Click to delete all the registered APs from the wireless distribution system allowed list. Reset Click the Reset button to abort change and recover t

  • Alfa Network AWAP602HW, Apply Changes Click the Apply Changes button to complete the new configuration setting. Reset Click the Reset button to abort change and recover the previous configuration setting. z DHCP Client Screen snapshot – WAN Interface Setup – DHCP Client Item Description DHCP Client Click to select DHCP support on WAN interface for IP address assigned automatically from a DHCP server. Host Name Fill in the host name of Host Name. The default value is empty MTU Size Fill in the mtu size o

Related Products and Documents (Network Router):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 Laser KB-BT500 Quick start manual laser/kb-bt500-34J.pdf 27 Dec 2023 7
2 Black Box LWE100A Quick start manual black-box/lwe100a-7QG.pdf 31 Mar 2023 24
3 HP DesignJet Z3100 Printing manual hp/designjet-z3100-WRE.pdf 27 Jun 2022 8 0.35 Mb
4 Tektronix WVR6UP Instructions manual tektronix/wvr6up-5E9.pdf 06 Jun 2023 32
5 Datavideo STC-100 Operation & user’s manual datavideo/stc-100-LO1.pdf 08 Feb 2024 14 0.43 Mb
6 Dell Latitude Latitude 13 Setup and features information dell/latitude-latitude-13-551.pdf 25 Jun 2022 5 0.34 Mb

Similar Resources:

  • Delta

    Loytec LIP-3333ECTC

    (4 pages)
    Installation instructionsLIP-3333ECTC CEA-709/IP routerInstructions de montageMontageanweisungMontagevoorschriftInstruzioni di montaggioInstrucciones de montajeMonteringsanvisning15989100164601315[.512][2.362][.591][3.937][3.504][6.260][6.457]LOYTECwww.loytec.comMade in AustriaEthernet 2Ethernet 1USB 1USB 2PWR1 2 3 4+-FT FTFT FTFTFTFTFTB AL-IPEIA709/IP rout …
  • Cisco

    TelePresence Server 7010

    (17 pages)
    1Doc. No.Copyright © 1995Cisco Systems, Inc.All rights reserved.600W AC-Input Power Supply and Fan TrayReplacement Instructions78-1233-02Cisco 7010 Product Numbers: PWR-7010AC= and ACS-7010FAN=Cisco 7505 Product Numbers: PWR/5-AC= and MAS/5-FAN=Customer Order Number: DOC-781233=This document contains instructions for replacing the 600W, AC-input powersuppl …
  • Cisco

    Aironet 340 Series

    (70 pages)
    Corporate HeadquartersCisco Systems, Inc.170 West Tasman DriveSan Jose, CA 95134-1706 USAhttp://www.cisco.comTel: 408 526-4000800 553-NETS (6387)Fax: 408 526-4100Cisco Aironet Access PointHardware Installation Guide340 Series and 350 SeriesText Part Number: OL-0738-02 …
  • ZyXEL Communications

    P-660HN-T1A

    (4 pages)
    How to set up Wireless on Zyxel P-660HN-T1A Router Modem 1. Setting up Wireless LAN 1.1. The AP (Access Point) Security Key Default is WEP 5-digit should be changed to WPA for higher security …
  • Buffalo

    WHR-G54S

    (6 pages)
    www.buffalotech.comQuick Setup Guide - AirStation WHR-G54SWireless Cable/DSL Smart Routerv2.5Package Contents• WHR-G54S AirStation• Antenna• Base• AC adapter and power cable• CAT5 LAN cable • Utility CD with Manual• Quick Setup Guides• Warranty Statement …
  • Linksys

    SPA2100

    (16 pages)
    !!!!!!!!!PLEASE&READ&!"#$%!&%'(!)*+&*,!$%!-(.)!/#'!)*+&-*0/&('(!1!Jive&Communications&may&not&support&some&features&discussed&in&this&document2!!!3,'*%'!%''!.&(!.+,$+'!4.0&)'+/*/$.+!.(!0.+/*0/!&%!-.(!*!0.)5,'/'!,$%/!.-!%& …

Comments, Questions and Opinions: