Afinia H800+ Quick Start Manual

Text of Afinia H800+ User Guide:

• Afinia H800+, 1 ¥ Accessory Pack Contents Verify the following items are in the H800+ packaging. 1. Filament 2. USB Cable 3. Power Cord 4. Power Supply 5. Putty Knife 6. FR-4 (Cell Perf) Boards (Four (4) total) Two (2) Flex Boards with BuildTak surface Two (2) Cell Perf Boards without BuildTak 7. Snipping Pliers 8. Nozzle Wrench 9. Spare Nozzle 10. Hex Wrenches 10 1 2 3 4 5 6 7 8 9

• 2 ¥ Unpacking 1. Remove foams from the H800+. Cut and remove the nylon ties (yellow labelled). There is no need to lift the platform to remove the bottom foams. 90° Note: Lay down the foam at the bottom, then turn it 90 degrees to remove.

• Afinia H800+, Install Print Board L ockedUnlocked guiding tube. Warning: Do not touch the platform while it is hot to avoid burns. 3 ¥ AFINIA Position the perf board on the build platform, and make sure that all the flat head screws on the heating plate are inside the holes of the perf board. Press the perf board and the heating plate together at the lower left and the lower right corners, then slide the perf board towards the back of the unit to lock it onto the heating plate. Make sure all holes are locked properly to ensure the perf board is flat. Install the filament spool and insert the filament int

• Build Download and install the latest Studio software from the support section of the Afinia website at www.afinia.com/support/downloads/. For the iPad or Install Software At the main menu “Build” 2 1 Connect power the Studio software. Click “Build” in the main screen, then “Initailize” . iPhone app, please visit the Apple app stor

• Afinia H800+, 500g the printer will beep two times and start to Next, go to the Maintenance Section, and click “Extrude”. In the “Build” menu, click “Calibrate” the auto leveling function. This process will take a minute to complete. Setup Printer 5 ¥ , then “Auto Level” to initiate When reaching printing temperature, extrude. Now gently push the filament into the small hole in the top of the printhead until extrusion occurs at the nozzle. When the extrusion completes, remove the thin line of extruded filament and discard.

• Afinia H800+, Setup Wi-Fi Go to “Printer” tab, select connected printer and click the stacked lines and enter the password for the Wi-Fi network. Open the “Settings” menu . Your_Network Your_Network 6 ¥ button to see printer details. Choose Network to connect to a Wi-Fi network

• Afinia H800+, Connect Printer Through Wi-Fi Disconnect the USB cable. Language Printer JSZ_BOX+_01 7 ¥ In the “Printer” section, all the printers in the network will be displayed. Click the H800+ you want to connect. If connected successfully, the printer will have a check mark displayed.

• Afinia H800+, open cancel 1. 2. Use the wheel to adjust the model’s size, location, and rotation. (see full manual details) 4. 5. 3. Click “Print”. Load and Print 3D Model Build 8 ¥ Click the “+” button, and choose an .STL or .UP3 file to load into the program. The progress of slicing and data processing is shown on the status bar. After data transfer is finished, the amount of material to be used and estimated print time will be shown.

More Instructions:

	Afinia H800+ Installation & setup manual 02-09-2023 2	DOWNLOAD
	Afinia H800+ Manual  03-08-2023 21	DOWNLOAD
	Afinia H800+ Operation & user’s manual 06-02-2023 46	DOWNLOAD

Related Products and Documents (Printer):

Comparable Devices:

Similar Resources:

• Posnet TEMO ONLINE (2 pages) Full version of the manual is available at www.posnet.com. This manual describes basic printer elements, installation of standard controllers and connecting the printer to a computer. Description of installation and configuration of controllers (USB(NET)) for online connections has been described in the Quick OnLine instruction attac …

• Xerox DocuColor 3535 (12 pages) QUICK START GUIDE Part Number: 450296742003  Electronics For Imaging, Inc. This Quick Start Guide provides system requirements and an overview of how to set up the Fiery Network Controller for DocuColor 3535 ™ so you can begin printing. The guide describes the initial tasks you must perform and points you to sections in the user documentation wher …

• Epson DM-D500 (2 pages) ENStart HereFor information on safety recommendations and basic operations, see User's Manual included on Manual CD. For detailed information, see Technical Reference Guide. You can access Technical Reference Guide from the included Manual CD.FRCommencer IciPour obtenir des informations sur les recommandations concernant la sécurité et le fonctionneme …

• Xerox PHASER 6250 (5 pages) Phaser® 6250 Color Laser PrinterCopyright © 2003 Xerox Corporation. All Rights Reserved.3-9Printer Management SoftwareThis topic includes:■ "Using CentreWare Software" on page 3-9■ "Using Printer Management Features" on page 3-11Using CentreWare SoftwareCentreWare Internet Service (IS)CentreWare IS is a printer administration and su …

• Canon imageRUNNER 8500 (2 pages) In order to be successful in the high-volume, Print-on-Demand envi-ronment, a device must consistently deliver high levels of outputwhile maintaining excellent image quality and machine reliability—day in and day out. Introducing the imageRUNNER™8500 NetworkedProduction System...a high-volume, high-performance networkedprinting solution engi …

• HP OFFICEJET 9100 SERIES ALL-IN-ONE 9110 (4 pages) HP Officejet 9100 series all-in-one 9110 • 9120 • 9130 Powerful performance • Enjoy fast printing and copying. Improve business productivity with speeds of up to 25 pages per minute (ppm) black and 22 ppm color in Fast mode. Reduce time waiting for your documents with a first copy out speed of 12 seconds. • Create professional color …

Comments, Questions and Opinions: