Manualios.com

Allied Data Technologies 810 Installation Manual

Allied Data Technologies 810 Manual Online:

3.9, 575 votes
Allied Data Technologies 810 User Manual
Allied Data Technologies 810 User Guide
Allied Data Technologies 810 Online Manual

Text of Allied Data Technologies 810 User Guide:

  • Allied Data Technologies 810, USB installation for Windows 2000. A: Place the CD-ROM provided in the CD-ROM drive. B: Connect your power adapter to the power outlet and into the Copperjet 81x. C: Connect your USB cable into your Copperjet 81x and your computer. D: Connect your RJ11 cable to your CopperJet 81x and into the phone outlet. 1. Click on Next. 2. Search for a suitable driver for my device, and click on Next. Allied Data Technologies 17 CopperJet 81x CJT 81x 02-10-2001 11:45 Pagina 17

  • Glossary ADSL Strictly speaking, Asymmetric Digital Subscriber Line defines only a way of transmitting broadband data (at speeds between 64kbps and 8Mbps) between a user’s premises (home or office) and the local telephone exchange. In order to increase the number of customers that it is possible to serve, the upstream speed (from the user) is lower than the downs

  • Allied Data Technologies 810, 6. ADSL Profile Configurator or Loader doesn’t detect an ADSL modem in your network - Check if the modem is in the same physical LAN as the configuring PC - Check if the modem’s IP address is in the same IP-subnet as the configuring PC. This IP-address can be found in the downloaded profile using the ADSL Profile Configurator. If the configured IP-address is not in the same subnet, then use the ADSL Profile Configurator or Loader from a PC which IP address is configured within the same subnet as your ADSL modem, or reset the modem to it’s factory default settings (see 4.). Review the profile (especially the IP-addresses

  • Allied Data Technologies 810, Configuring PPPoA. 1. Select PPPoA as profile type and click on OK. 2. Set Authentication. Fill in your Username and Password. Choose the Authentication Protocol.(PAP or CHAP) Set the LAN TCP/IP parameters. (CopperJet 81x IP-Address) The Default Gateway of your local network will be the CopperJet 81x IP-Address Set the interface type. USB when the CopperJet 81x is connected with a USB cable. Ethernet when the CopperJet 81x is connected with a Ethernet cable. Select the Line modulation.(ADSL connection Protocol) -Multimode : Modem will detect the Modulation offered by the CO (Preferred) -T1.413 : ANSI ADSL Standard -G.Lite : G.992.2 -G.Dmt : G.992.1 Annex

  • Allied Data Technologies 810, CopperJet 81x Allied Data Technologies 57 Declaration of Conformity Manufacturer’s Name: ALLIED DATA TECHNOLOGIES B.V. Manufacturer’s Address: P.O. box 788 3200 AS Spijkenisse The Netherlands declares that the product: Product Name: CopperJet 813 Conforms to the following standard(s) or other normative document(s): Safety: EN 60950 (1992/93) Safety of information technology equipment, including electrical business equipment. CE: Statement of Conformance to electrical safety & EMI requirements Supplementary Information: The product was tested in a typical configuration. Spijkeniss

  • Allied Data Technologies 810, Configuring RFC1483 Bridged. 1. Select RFC1483 Bridged as profile type and click on OK. 2. Set the TCP/IP parameters. Optional: an IP Address and Subnetmask is only needed for further management use. Select the Line modulation. (ADSL connection Protocol) -Multimode : Modem will detect the Modulation offered by the CO (Preferred) -T1.413 : ANSI ADSL Standard -G.Lite : G.992.2 -G.Dmt : G.992.1 Annex A Set the ATM PVC (Virtual Circuit) parameters. -VPI : VPI Channel Number -VCI : VCI Channel Number -PCR : Peak Cell Rate Select the forwarded Packet types. -None : This will forward all packets -Forward PPP: This will only forward PPP packets -

  • Allied Data Technologies4 CopperJet 81x Ethernet Installation Guide Note: You must have installed an Ethernet 10Base-T card in your computer first. Installation when you already have a LAN connection. 1. Connect your CopperJet 81x with the Ethernet straight cable to your Ethernet Hub. 2. Connect your RJ11 cable to your CopperJet 81x, and into the phone outlet. 3. C

  • Allied Data Technologies 810, Configuring PPTP. 1. Select PPTP as profile type and click on OK. 2. Set the LAN TCP/IP parameters. (CopperJet 81x IP-Address). The Default Gateway of your local network will be the CopperJet 81x IP-Address Set the interface type. USB when the CopperJet 81x is connected with a USB cable. Ethernet when the CopperJet 81x is connected with a Ethernet cable. Select the Line modulation.(ADSL connection Protocol) -Multimode : Modem will detect the Modulation offered by the CO (Preferred) -T1.413 : ANSI ADSL Standard -G.Lite : G.992.2 -G.Dmt : G.992.

  • Allied Data Technologies 810, CopperJet 81x Allied Data Technologies54 Declaration of Conformity Manufacturer’s Name: ALLIED DATA TECHNOLOGIES B.V. Manufacturer’s Address: P.O. box 788 3200 AS Spijkenisse The Netherlands declares that the product: Product Name: CopperJet 811 Conforms to the following standard(s) or other normative document(s): Safety: EN 60950 (1992/93) Safety of information technology equipment, including electrical business equipment. UL (IEC950) Statement that the equipment has been designed and built according to IEC950 and/or the compatible edition of EN60950. CE: Statement of C

  • Retrieving the profile from your CopperJet 81x. With the CopperJet configurator you will be able to retrieve your profile from your CopperJet 81x. 1. Start the CopperJet Configurator. 2. Click on the MAC address, and click on Get profile. 3. Give the profile a file name e.g Save, and click on Save. 4. Click on Ok. Allied Data Technologies40 CopperJet 81x

  • Allied Data Technologies 810, Allied Data Technologies 5 Installing the CopperJet 81x Configurator. After installing the CopperJet configurator you be able to configure the CopperJet 81x. During installation you can choose the setup you prefer, Typical this will install the most common options. Compact this will install only the CopperJet configurator. Custom you may choose the options you want to install. 1. Place the provided CD-ROM in the CD-ROM drive. Browse on the CD-ROM to the following directory. D:\CJT_810_EU\Configurator, and double click on Setup.exe. 2. Click on Next. CopperJet 81x CJT 81x 02-10-2001 11:45 Pagina 5

  • Allied Data Technologies 810, Updating the firmware in the CopperJet 81x. With the CopperJet configurator you can upload a new firmware into your CopperJet 81x. New firmware will be available on our website. Note: Don’t disconnect the power suply, USB cable or Ethernet cable during the upload. 1. Start the CopperJet Configurator. 2. Click on the MAC address, and click on Update firmware. 3. Select the binary to upload, and click on Open. Allied Data Technologies42 CopperJet 81x CJT 81x 02-10-2001 11:45 Pagina 42

  • Allied Data Technologies 810, Allied Data Technologies30 Set NAT (Network Address Translation) if needed. You must set NAT when de LAN IP-Address differs from the WAN IP-Address. DNS Relay. Fill in the DNS server IP-Address, in your local network the DNS IP-Address will be the CopperJet 81x IP address. Set the DHCP server when needed. The CopperJet 81x can act as a DHCP server. Go to the DHCP server section how to configure the DHCP server. Click on OK when finished, the profile will be stored in My Documents. The profile can be uploaded to the Copperjet 81x as described in the upload section. CopperJet 81x CJT 81x 02-10-200

  • Allied Data Technologies 810, CopperJet 81x Allied Data Technologies52 Declaration of Conformity Manufacturer’s Name: ALLIED DATA TECHNOLOGIES B.V. Manufacturer’s Address: P.O. box 788 3200 AS Spijkenisse The Netherlands declares that the product: Product Name: CopperJet 810 Conforms to the following standard(s) or other normative document(s): EMC: EN 55022 Class A (1994) Limits and methods of measurement of radio disturbance characteristics of information technology equipment. EN 50082-1 (1992) Electromagnetic compatibility - Generic immunity standards for residential, commer

  • Allied Data Technologies 810, Allied Data Technologies 9 CopperJet 81x USB Installation for Windows 98 SE. During the installation you need the official Windows 98 SE CD-ROM. A: Place the CD-ROM provided in the CD-ROM drive. B: Connect your power adapter to the power outlet and into the Copperjet 81x. C: Connect your USB cable into your Copperjet 81x and your computer. D: Connect your RJ11 cable to your CopperJet 81x and into the phone outlet. 1. Click on Next. 2. Click on Next. CJT 81x 02-10-2001 11:45 Pagina 9

Related Products and Documents (Modem):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 Magnavox PR1917 Owner's manual magnavox/pr1917-YD2.pdf 01 Aug 2023 20
2 National Instruments 8330 Series Operation & user’s manual national-instruments/8330-series-3PZ.pdf 29 May 2023 30
3 Lorex DMC2030 Series Frequently asked questions manual lorex/dmc2030-series-81E.pdf 22 Dec 2022 8
4 Hunter Piccolo Owner's manual hunter/piccolo-TZ1.pdf 27 Jan 2024 8
5 TRENDnet TEW-652BRU Datasheet trendnet/tew-652bru-FL3.pdf 30 Mar 2023 3 0.86 Mb
6 Panasonic DT60 series Ehelp panasonic/dt60-series-JO2.pdf 13 Nov 2022 224 1.82 Mb

Similar Resources:

  • IpCAS

    ipEther232

    (98 pages)
    ipEther232 ipEther232.Modem ipEther232.PPP ipNTP User Guide ipcas GmbH Wetterkreuz 17 D-91058 Erlangen Telefon: +49 9131 7677 0 Telefax: +49 9131 7677 78 Internet: http://www.ipcas.de E-Mail: [email protected]
  • SpeedStream

    5100-a

    (6 pages)
    Page 1 of 6OverviewThis troubleshooting and setup guide was created to assist you in ensuringthe continued maintenance of your Internet connection with the EfficientSpeedStream 5100-a modem and other related equipment.This document offers you the first line of troubleshooting should you experiencea connection problem. It also provides you with instructions f …
  • Sixnet

    VT-MODEM-5

    (23 pages)
    VT-MODEM-5 User Manual Page 1 of 23 Last Revised: 3-Jun-05 SIXNET • Box 767 • Clifton Park, NY 12065 USA • +1 (518) 877-5173 • FAX +1 (518) 877-8346 • mailto:[email protected] VT-MODEM-5 Advanced 56K Modem Installation & Maintenance Contents at a Glance: Section 1 Overview 2 Section 2 Performance Specifications 3 Section 3 VT-MODEM …
  • Acanac

    CBN8000

    (2 pages)
    Use the app to customize your Wi-Fi Network (SSID) name and password.  parental controls, anti-virus and how to create • � …
  • Tenda

    3G186R

    (2 pages)
    All For Better NetworkingMobile WiFi always with youIt's a 3G modem, also is a wifi n router 3G186R is a mobile wireless modem router designed for business professionals and people who travel often. It's developed based on WCDMA and IEEE802.11n technologies. Just put a 3G-enabled sim card on it and it becomes a 3G modem that provides up to speeds o …
  • Arris

    Touchstone TM402

    (52 pages)
    1 Product SpecificationsThis chapter details the Touchstone™ Telephony Modem product specifications.2 Installing the Telephony ModemThis chapter explains how to install a new Telephony Modem at a subscriber site.3 Installing the Telephony Modem USB DriversUse this procedure to install USB drivers for the ARRIS Touchstone™ Telephony Modem on a Windows sys …

Comments, Questions and Opinions: