Manualios.com

Renkforce RF1000 Manual 

Renkforce RF1000 Manual Online:

3.45, 1609 votes
Renkforce RF1000 User Manual
Renkforce RF1000 User Guide
Renkforce RF1000 Online Manual

Text of Renkforce RF1000 User Guide:

  • 5 • Never reach into the 3D printer in operation. The mechanically moved parts within the printer pose a high risk of inju- ry! • The print head and the heating plate grow very hot in operation. Never touch these parts during or just after operation. Let them cool down suciently first (approx. 60 minutes). • The mains unit corresponds to the applicable CE p

  • Renkforce RF1000, 54 11. Final Work If the motors are moved manually, the display may light up. This is not a malfunction. A voltage induced by the movement causes the display to light up. Connection of the earthing plate Place the heating plate onto the spacer bolts of the undertable and connect the two plug connectors from line 12 and 20. Basic setting limit switch Z-direction Loosen the actuation screw in the Y-plate for the limit switch in the Z-direction and turn it all the way into the hexagon bolt. Carefully turn the toothed belt of the bottom plate until there is a gap of 0.5 mm (+/-0.2 mm) set between the heating plate and extruder. 0.5 mm correspond roughly to the thickness of 5

  • Renkforce RF1000, 55 Discharge tensions of the threaded circulation spindles Slightly loosen the attachment screws of the threaded circula - tion spindles on both sides of the printer (4 screws each) again and then tighten them again. This avoids tensions that may cause sti movement when mov- ing the Z-axis in operation. Attachment of the bottom cover Turn the rubber feet o the foot holders. Insert the bottom plate with the folds towards the housing feet. First insert the edge at the housing rear and then fold the bot- tom plate against the housing. Align the bottom plate with the bores for the housing feet and attach it w

  • Renkforce RF1000, 46 Connect the protective ground (green/yellow line with ring eyelet) with a cylinder head screw M3x10, a washer and two sprockets at the top of the undertable. Caution: This connection creates the safety-technically im- portant contact between the housing parts and the protec- tive ground. Always observe the position of the washers and sprockets: Screw head > washer > sprocket > ring eyelet > sprocket > undertable (see image section) Connect line 13 with the plug connector of the limit switch for the Y-direction and place the line. Let line 12 protrude from the drag chain by about 8 cm and at- tach it to the bore in the undertable with a small

  • Renkforce RF1000, 32 Assembly of the Mechanical Basic Construction Connection of the bottom plate to the Y-plate 1x bottom plate 1x Y-plate When inserting the thread circulation spindles into the bottom plate, always observe that the spindles are turned out precise - ly the same length and are not oset against each other. If this is not the case, the thread circulation spindles must be adjusted to each other by turning. Thread the Y-plate into the spacers of the bottom plate with the two mill-outs from above. The thread circulation spindles must be cleanly flush against the grooved ball bearings in the bottom plate after assembly. Assembly of the X-plate 1x basic frame

  • Renkforce RF1000, 96 • In the menu “Tools”, select the option “Serial port” and set the correct port. The port number is system-dependent. You can find it in the device manager of the control panel, under connections (COM and LPT). • In the menu “File”, choose the option “Open...” and select the file “repetier.ino” from the downloaded firmware folder. The file “repetier.ino” can be found via the following file path: “Repetier-Firmware-master\src\ArduinoAVR\Repetier”

  • Renkforce RF1000, 103 The filament supply breaks o or there is not enough filament material supplied: • Check the filament unroller. It must turn easily. • Check whether the filament material has caught on the filament unroller. The filament hose at the filament roller may have caught. • Some filament types do not slide through the filament hose properly. If required, use the alternative filament holder that you can print from the SD card (file name “Filament_guide.gcode”). • The set extruder temperature is too low for the filament mat

  • Renkforce RF1000, 30 Assembly of the undertable 1x undertable 1x Y-plate 4x countersunk head screw M4x12 Attach the undertable with the 4 countersunk head screws to the undertable holder as shown. Apply screws with threadlocker varnish. Assembly of the thread circulation spindles The nuts on the threaded circulation spindles must never be removed from the threaded circulation spindles, since the bearing balls would fall out otherwise. This would be irreparable. 2x threaded circulation spindle 1x Y-plate 8x cylinder head screw M5x16 Attach threaded circulation spindles to the Y plate as shown with 4 screws each. Observe the position of the lubrication ni

  • Renkforce RF1000, 106 b) Notes on the Print Files (GCODE Files) on the Enclosed SD Card The folder “GCODE” on the enclosed SD card holds various finished printing files. These files do not need to be sliced with a software like the Repetier-Host first. They can be printed right from the SD card (also see “First Print of an Example Object from the SD Card”). The files are saved in the folder “ABS” and “PLA”, depending on the filament type used. Example: Heart.gcode in the folder ABS = small heart for printing with ABS filament c) Setup of the Printer Settings This chapter is only targ

  • Renkforce RF1000, 14 1x X-plate 1x guide carriage complete with assembly aid Carefully push the guide carriage onto the guide rail and push the assembly aid (plastic part) from the guide carriage while doing so. Attaching the limit switch for the X-direction 1x X-plate 1x limit switch 1x holder for limit switch 2x cylinder head screw M2x6 2x cylinder head screw M3x10 Install the limit switch PCB with the M2x6-screws to its holder so that the plug connector points away from the holder (see figure). Then align the limit switch with the holder wit

  • 58 b) Insertion of the Filament Pull the filament hose end from the infeed basic part. Push the filament roller onto the filament holder and guide the filament through the filament hose until it escapes on the other side. The filament roller must move freely. Remove the two upper spring screws at the extruder and pull back the filament guide plate with the ball b

  • Renkforce RF1000, 94 17. Filament Change Before filament change, the extruder must be heated so that the old filament can be cleanly replaced from the extruder. Do not touch the hot extruder nozzle when replacing the filament, danger of burns! Always wait for the extruder temperature to be reached at filament change and let the extruder heat for approx. ano - ther minute, since the extruder may break otherwise. (1) Switch on the extruder heating. (2) Set a temperature suitable for the inserted filament material (ABS: 270 °C / PLA 230 °C). (3) When the temperature is reached, let the extruder heat for approx. another minute and then move the filament material o

  • Renkforce RF1000, 101 e) Nozzle Change Caution: Danger of burns. Do not touch the hot nozzle or the extruder directly. • To replace the extruder nozzle, the extruder must first be heated to a temperature suitable for the inserted filament material. • When the temperature is reached, remove the inserted filament material as described in “Filament Change”. • Screw o the extruder nozzle (1) from the extruder with a 10 mm hexagon wrench (2). Always secure the extruder against twi - sting at the flat

  • Renkforce RF1000, 71 c) Connection of the Connected Printer Start the programme Repetier-Host and select printer settings at the upper right in the window. (1) Set the port and baud rate as displayed. The port number is system-dependent. You can find it in the device manager of the control panel, under connections (COM and LPT). (2) Click “OK”.

  • Renkforce RF1000, 59 c) Setup and Transport When setting up the 3D printer, observe that the mains switch at the low power device combination socket must be easy to reach so that the device can be switched o quickly and easily in case of malfunction. Ensure proper ventilation when setting up the device. Do not put the device down on soft supports such as a carpet or bed, etc. the air circulation also must not be impaired by other objects. This prevents heat dissipation from the product and may lead to overheating (danger of fire). When setting up the device, make sure that it has a stable footing and place i

  • Renkforce RF1000, 2 Table of Contents ( Page 1. Introduction ................................................................................................................................................................................................... 3 2. Explanation of Symbols ............................................................................................................................................................................... 4 3. Intended Use ................................................................................................................................................................................................. 4 4. Safety Information

  • Renkforce RF1000, ( Legal notice These operating instructions are a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com). All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in electronic data processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited. These operating instructions represent the technical status at the time of printing. Changes in technology and equipment reserved. © Copyright 2014 by Conrad Electronic SE. V1_0514_01

  • Renkforce RF1000, 61 Push OK Select „Extruder“ with the direction buttons. Push OK and select „Bed Temp“ with the direction buttons. Push OK Set „100 °C“ with the direction buttons. Push OK Push the direction button „left“ 2x to return to the main menu. Wait until the actual temperature of the heating plate in the display indicates 100 °C and then let heating continue for ap - prox. 5 more minutes until the temperature of the heating plate has stabilised. Push OK and select „Configuration“ with the direction but -

  • 44 Turn the toothed belt at the base plate manually so that the Y- plate moves up. Keep turning until the alignment of the limit switch just installed can be adjusted. The limit switch must be aligned so that it can be actuated by the slotted screw in the Y-plate. Caution: When making this setting, observe that the extruder does not impact anywhere, which would damage it. Pla

  • 9 Application of the threadlocker varnish In the following instruction, some screws must be secured with threadlocker varnish. This is indicated accordingly in the text. Procedure: Put a small drop of threadlocker varnish medium-strength onto the thread start. Observe that you must only use a small drop as shown in the following screen. b) Assembly of the Components Attachment of the

  • Renkforce RF1000, 50 Installation of the main PCB 1x main PCB 5x spacer roller 20 mm 5x cylinder head screw M3x25 5x nut M3 Install the main PCB with the spacer rollers 20 mm as shown. The spacer rollers may be fastened to the PCB with a drop of hot glue for easier assembly first. Apply all screws in the area of the nuts with threadlocker var- nish. Align the PCB so that the USB connection and the memory card reader are placed cleanly behind the respective housing cut-outs. Connection of the lines at the mains unit 1x mains unit 1x line with flat plug connector black (short) 1x line with flat plug connector blue (short) 1x line with flat plug connector green/yellow (short) 1x line black

  • Renkforce RF1000, 86 (1) Setting of the nozzle diameter (2) Settings for the filament withdrawal if the extruder moves to another position of the printed object during printing. If the filament was not withdrawn here, there would be drop or string formation that would negatively influence printing quality. 16. Software “Cura” a) General Notes on Software It is unfortunately not possible to explain the complete function of the “Cura” software in the scope of this instruction. We refer to the instructions and the forum under www.ultimaker.com. The basic operation and the path to the first printout ar

Related Products and Documents (3D Printers):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 The Singing Machine SML329 Instruction manual the-singing-machine/sml329-92S.pdf 03 Jan 2023 12 3.87 Mb
2 Philips HQ7782/16 Manual  philips/hq7782-16-561.pdf 20 Oct 2022 136
3 Lightolier 1050SQSLW Specification lightolier/1050sqslw-B64.pdf 13 Jul 2023 4
4 GE JS900 Dimensions and installation information ge/js900-M33.pdf 24 Mar 2023 2
5 Panasonic CQ2700EU - AUTO RADIO/CD DECK Operating instructions manual panasonic/cq2700eu-auto-radio-cd-deck-Z44.pdf 24 Aug 2022 24 0.89 Mb
6 Duo-Therm 3109228.001 Operating instructions manual duo-therm/3109228-001-52A.pdf 28 Oct 2022 8

Similar Resources:

  • Dremel

    3D40 FLEX

    (588 pages)
    2610Z10167 11/2019 All Rights ReservedOriginal instructions 2Übersetzung der Originalbedienungsanleitung 32Traduction de la notice originale 63Traducción de las instrucciones originales 94Tradução das instruções originais 125Traduzione delle istruzioni originali 156Vertaling van de originele gebruiksaanwijzing 187Oversættelse af betjeningsve …
  • Flashforge

    ADVENTURER 3

    (24 pages)
    本手册仅适用于闪铸科技 Adventurer3 3D打印机This guide is only applicable to FLASHFORGE Adventurer3 3D printer快速启动指南ADVENTURER 3 / 冒险家 3Quick Start Guide中文P11SZ16-ZN/EN-A05 …
  • Flyingbear

    TORNADO

    (26 pages)
    Flyingbear-Tornado Installation Manual1.Frame installation------------------------------------------------------------12.Driving wheel and idler wheel installation---------------------------23.Y-liner guide rail installation----------------------------------------------34.X-linerguider rail installation---------------------------------------------55.Z-hot be …
  • EasyThreed

    X7

    (11 pages)
    深圳市普伦特科技有限公司 www.easythreed.com 1 / 10 X7 Use’s Manual Please watch operation video in Website or YouTube Channel:Easythreed 3D …
  • Raise3D

    PRO2 Series

    (5 pages)
    WWW.RAISE3D.COM AMERICA · ASIA · EUROPE Pro2 Endstop Limit Switch Board Installation Instruction Pro2 Endstop Limit Switch Board Installation Instruction STEP 1: The Locations of Endstop Boards Z-Endstop Board X-Endstop Board Y-Endstop Board …
  • PhotoCentric

    Air Wash L

    (4 pages)
    Air Wash Lwww.photocentricgroup.comUK - Cambridge House, Oxney Road, Peterborough, PE1 5YW. +44 1733 349937USA - 2205 West Parkside Lane, Phoenix, 85027, AZ. (623) 581-3220Air Wash LPHOTOCENTRICAIR WASH LINSTALLATIONGUIDERevision 106/10/2020 …

Comments, Questions and Opinions: