Manualios.com

Roland MSQ-1QO Owner's Manual

Roland MSQ-1QO Manual Online:

4.85, 2820 votes
Roland MSQ-1QO User Manual
Roland MSQ-1QO User Guide
Roland MSQ-1QO Online Manual

Text of Roland MSQ-1QO User Guide:

  • Roland MSQ-1QO, The Roland MSQ-100 Digital Keyboard Recorder is specially designed for polyphonic keyboards featuring MIDI. Features » Both Step Loading and Real Time Loading are possible. » An Overdubbing function behaves like a Mix Down on recording equipment. • Various edit functions are provided, allowing quick and easy data correction. • The LCD is used for easy grasp of the current condition of the MSQ-100. • A MIDI Channel Shift function makes it possibe to change the MIDI Channel of the MSQ-100 (transmi

  • Roland MSQ-1QO, 3] Applications 1. DIN SYNC The MSQ-100 can be perfectly synchronized with the device featuring the DIN Sync function. a DIN SYNC IN Jack Connect this jack to the SYNC OUT of the external device. Then set the Clock Source Switch @ to SYNC. The MSQ-100 serves as a Slave unit (being controlled by an external unit), therefore the exter- nal unit controls the tempo, start/stop function, etc. SYNC IN OUT SYNC OUT to SYNC IN b DIN SYNC OUT Connect this jack to the SYNC IN of the external device, then set the

  • Roland MSQ-1QO, [H Appendix Appendix 1. Operation Table 1. Load/Play Mode a. Load Mode | LOAD MOOE*] \ — ] | LOAO MQOe] J .. ~| b. Display Mode © IDISPLAYJ ® © |DlSPLAY| j^- | c. MIDI Channel Shift © <£> ——J [_MIDiC EI C — — l L © © f~MIDI CH | [ - — I d. Measure Set FWD ME AS BACK MEAS RESET e. Load © Real Time Load - Load Mode -j — y- Measure Set (Set the Measure) INT Data Input MIDI -O O-s LOAD I SYNC • Step Load /Go to the \data head External START/- Data Input -^ I STOP I STOP I External Load Mode —? y Measure Set -r l LOAD | -Data Input Operation • i STOP f. Play ©Play Measure Set INT MIDI PLAY o-H SYNC External Astart/" ' r~ H L_ ® -+ Played up I ST

  • Roland MSQ-1QO, D Specifications Memory Capacity Approx. 6100 single notes without Key Velocity. Front Panel Mode Switch (PLAY, LOAD/PLAY, DATA TRANSFER) Metronome Level Switch (HIGH, LOW, OFF) Clock Source Switch (INT, MIDI, SYNC) Tempo Volume ( = 35 to 240) Tempo Indicator Reset/Verify Button Load Button Stop/Shift Button Play/Save Button Play Indicator Repeat Play/(MIDI/TAPE) Button Repeat Play/MIDI Indicator Liquid Crystal Display Load Mode Indicator 3 (4/ 4 , 3/ 4 , OVER DUB,^ ,?,^) Back Measure/Back Step/ j—

  • Roland MSQ-1QO, © Firstly, load the bass part on channel 1. © Secondly, dub the chord backing part on chan- nel 2. (MIDI Channel Shift number in the Dis- play should be 1.) © Finally, dub the melody part on channel 3. (Channel Shift number is 2.) Play the data. All bass, chord and melody parts will be simultaneously played, on channels 1,2 and 3. b. Using 2 sets of MSQ-100's Using 2 MSQ-100's allows advanced editing such as overdubbing in Step Loading mode. CH.1 CH. 1 MIDI keyboard OUT in | CH.2 CH.3 MIDI Sound Module OUT IN MSQ-100 (A) CLK = INT Function Switch UMIDIOUT-ON IN OUT OUT MIDI Sound Module IN OUT MIDI Sound Module IN j MSQ-100 (B) CLK= INT in operation ©, otherwise MIDI Functi

  • Roland MSQ-1QO, 2. Rear Panel Function Switches ©Tape Load Jack ©Tape Save Jack FUNCTION SW TAPE LOAD SAVE [iHlRoIand midi digital keyboard recorder MSQ-1GO FUNCTION SW METRONOME BEAT KEY VELOCITY BENDER CONTROL CHANGE MIDI OUT THRU TAPE SAVE LEVEL TAPE LOAD MODE Roland Corporation JAPAN &MIDI IN Jack ©MIDI OUT/THRU Jack )MIDI OUT Jack START/ STOP DC IN © ©AC Adapter Jack Start/Stop Jack (H) DIN Sync Out Jack )DIN Sync In Jack «Funct8on Switches» 1. Metronome Beat Switch (Do not touch this switch while the MSQ-100 is running.) This selects the Metronome beat (J or P ), for loading or playing.

  • Roland MSQ-1QO, Appendix 2. Multi Operation Switches c o 3 -Q TJ O a o co V CO o < <f LU CQ ^ ^ ca £ c co O CO 4-" 03 . ^ 3 a 3 03 -a E o ca aj a. <r o Q E S ^ 13 tj 3 J2 Q3 ca T o TJ £ O 5 CO 1c jz en 13 Q. CO 'a IE .2 J2 03 r* c c ca CO Q.TJ 03 O :*: a. O LU <h- DQ CO T3 x: LU Qlu oh ^z Q< <X oo -J 03 -a o en 03 § f-5 t T s h- o co III CO LT JZ CO CO Q-x: a) = ai a. 2 £ «: § = S £ CO < LU Q LU O CO 03 ^ -C C CO l_ CO 03 ca n tj jz tj « — £ JZ DQ CO o > a o u a o 03 H TJ O LT LU CO c -? CO c LU TJ O h- LU ^ .J LU a n Y <£ a u in o JZ CJ o h- Q. £ ,0 C 03 O £ + - 3 Jam _ .E So o JZ 2* 8 5 "8 CL £ -J a o a o CO y "

  • Roland MSQ-1QO, c. Insert The Insert mode allows you to insert a measure of music data into the existing data. A B C D i i E F 2 2 A [ 5 e) 7 A B E F C D © Set the Mode Switch Q to Load/Play. ® By using the [- — 1 Button ©, Button © and the Load Mode Button ©, select any Load Mode you like except for Overdub. ® By using the Reset Button ©, Back Measure Button © and Forward Measure Button ©, go to the measure where you wish to insert new data. RESET Set to the 1st measure -* Back-up one measure Forward one measure © While holding the Shift Button © down, press the Insert Button ©, and the MSQ-100 is turned to the Insert mode. While holding

  • Roland MSQ-1QO, ® By using the Reset Button ©, Back Measure Button © anc * Forward Measure Button ©, go to the measure where you wish to start loading. In this example, press the Reset Button to go to the very beginning. RESET Set to the 1st measure Back-up one measure (D Press the Load Button ©. The Load Indicator lights up and Step Load- ing starts. From now on, the switches ©, ©, ©, © and ©all work as shown in "*Multi Operation Buttons in Step Load mode." © Load the music data by playing the instru- ment and using

  • Roland MSQ-1QO, (3) To turn the MSQ-100 to the Delete mode, press the Delete button © while holding the Shift Button © down. While holding down m * ® | SHIFT 1 [delete) "_i 3 U _i Press the Load Button ©, and the measure will be deleted. If you wish to delete the next few measures, just press the Load Button as many times. (5) Press the Stop Button ®, or reset Button ©, and the Delete mode will be cancelled. <Note> * All the Edit operations are done measure by measure. Therefore, it is necessary to get to the beginning of the measure before setting the MSQ-100 to an Edit mode. It is not possible to set it to the Edit mode in the middle of a measure. (The display shows HRL F .) If

  • ) Repeat v- Measure Set -^ ( Play ^ © f Q-> PLAY STOP <E) Fytprnal k tSTART/~ ^ External ISTOWi - ) RESET 9 Edit ©Copy ) Erase Measure Set Measure Set © | SHIFT | | COPY | <E> | ERASE | ) Insert Load Mode -7 — 7- Measure Set SHIFT I | INSERT | Yes No Yes I LOAD No Yes STOP RESET STOP RESET -Data Input - STOP LOAD ( No STOP © RESET ® Delete Measure Set . © ® Yes © J 1

  • Roland MSQ-1QO, (T) Make sure the MSQ-100 is not running. (2) Press the MIDI Channel Button®. The Display will show a number as long as the button is pressed down. * The number shown in the Display means the number added to or subtracted from the cur- rent MIDI Channel number. In this manual, we call this the Channel Shift number. * The Channel Shift number is zero right after power on, and the Display reacts as shown below. * If this new channel number happens to be less than zero, or bigger than 17 (such as -2, -5, 18 or 20 etc.), that will be ignored. Therefor

  • Roland MSQ-1QO, [3] Operation MIDI IN MIDI OUT H- MSQ-100 J- To Amplifier OUTPUT MIDI OUT MIDI IN JUNO-106 JX-3P TR-909 etc. 1. Load In this manual, writing music data into memory is called "Loading". There are two methods of load- ing, Real Time Loading and Step Loading. a Real Time Loading (1) In this mode, what you play will be loaded exactly as it is played. Normally, the performer plays to a metronome. (T) Set the Mode Switch © to Load/Play (Protect off). © While hold ing the Load Mode button ©, press h— I ® or | — H ©, selecting 4 /4 or 3 /4. While holding this {

  • Roland MSQ-1QO, s- Loading a Tie (in J* mode) - Pressing the Tie Button will make the timing value one step longer. Press them at precisely the same time. If loading m MM Release the keys Press the Tie Button three times. s- Special Use of the Tie Button (in } mode) 1) Legato Load the first note in the usual way, and the next one by pressing the relevant key while holding the Tie Button down. If loading ffl ^Release the^ Press tne ^ P | ay d, E and F in _^ Release the key. "^ Tie Button "^non legato manner. - * Tie Button _Keep the Tie But-_ ton held down. 2) Tie +

  • Roland MSQ-1QO, 2) Verify © Rewind the tape to the beginning of the data. If your tape recorder features a playback level control, set it to medium volume. ® Set the Mode Switch Q to Data Transfer, and the Switch © to Tape. The Display shows ® Press the Verify Button. The display shows " \J" (verify). © When verification is finished, the Display shows "IJ.uaod " (verification good). If "u. £ r r " is shown instead, repeat the verification procedure. Please read "Notes on Verify and Load". ® Stop the tape recorder, then press the Stop Button © on the MSQ-100. © Play the tape recorder. When the head

  • Roland MSQ-1QO, 6. Channel Erase If you happen to make an error while overdubbing using a new MIDI Channel number, the Channel Erase function can be effectively used, because this function allows you to erase the data on the Channel number you assign independently. © Set the Mode Switch Q to Load/Play. (2) By using the Reset Button ©, the Back Mea- sure Button ® and the Forward Measure But- ton ©, go to the first measure of the data to be erased. RESET -*» Set to the 1st measure Back-up one measure Forward one measure By using the MIDI Channel Button© Button ££ the set I—-I Button © and the F— an appropriate MIDI Channel Shift number to assign the MIDI Channel you wish to

  • Roland MSQ-1QO, 3. Overdub (1) The overdub mode allows you to add more data on top of existing data. While listening to the existing data playing, you can overdub new data in real time. © Set the Mode Switch © to Load/Play. © By using the H — I Button ©, I — H Button ©, and Mode Button ©, set the Load Mode to Overdub. While holding down { lqao mope \ © r=n r^=i OVER DUB \ I / -E3- © An Overdub can be done in exactly the same way as Real Time Loading, but note that the MSQ-100 stops at the end of the existing data. If you wish to stop overdubbing in the middle of the existing

  • Roland MSQ-1QO, 'Ql* type data format Phrase data format A file of sequence data contains a [FCB], [TD| and [ED]. 4.1 [FCB] File control block This is the file control block which contains fixed 40 bytes tota It is sent under an exclusive message. descr ipt ion name # of bytes a) Header 1 byte b) Block Type 1 byte c) Data type 2 bytes d) File Name 30 bytes e) Conductor sw 1 byte f) track num 1 byte g) phrase num 2 bytes h) tine base 1 byte i) tempo 1 byte j) EOB 2 byte $FD ' F 1 in asc i i 'Ql ' in asc i i 'MSQ-100.0', 21. spaces $00, off $ 00, none of tracks $01, $00 $78, time base = 120 $64, (no function) $FE, $FE 4.2 [P

  • Roland MSQ-1QO, 5. Data Transfer The MSQ-100 features a Tape Interface function that allows you to save the data in memory onto a tape. Moreover, data transfer between two MSQ- 100's is possible by means of MIDI. a. Tape Interface Function • Connection For Saving For Loading or Verifying TAPE © ® LOAD SAVE TAPE ® ® LOAD SAVE o o LINE IN LINE OUT (MIC IN) (PHONES/MONITOR) Tape Recorder o o Tape Recorder In some tape recorders, loading or verifying is not possible with both jacks connected. * Save Recording the music

  • Roland MSQ-1QO, 4. Edit The MSQ-100 features the Edit functions of Copy, Erase, Insert and Delete. * When the MSQ-100 is in the Edit mode the Display Window shows the measure number currently being edited. If you with to cancel the Edit mode, simply press the Stop Button ©. a. Copy The Copy function allows you to copy a measure of the existing music data. A B C D i C ' 1 • 1 Copy k For instance, if you have loaded 4 measures, but wish to copy the 3rd measure to the end of the existing data (to the 5th measure), do as follows. © Set the Mode Switch Q to Load/Play. ® By using the Reset Button ©, Back Measure Button © and Forward Measure Button ©, as- sign the measure n

  • Example Operation By repeating this procedure ®, as many mea- sures as required can be copied. When the data to be copied (Original) consists of more than one measure, and also includes Bender effect, the copied data may not be played correctly. 7 8 LOAD LOAD LOAD A' -© -© -®- •© LOAD C D' T ( LOAD ® /_. C ® *_. D ® r u ® «_. D b. Erase The Erase

  • 1. RECOCNIZED RECEIVE DATA 1.1 Memorized messages while in LOAD mode Status Second Third Description 1000 nnnn 1001 nnnn 1001 nnnn 1010 nnnn 1011 nnnn 1100 nnnn 1101 nnnn 1110 nnnn 1111 0000 Okkk kkkk Okkk kkkk Okkk kkkk Okkk kkkk Occc cccc Oppp pppp Ovvv WW Ovw WW 0100 0001 1111 0111 Ovw ww 0000 0000 Ovw ww Ovw ww Ovw ww Ovw ww 0100 0010 (EDX) Note OFF *1, 2 No

Related Products and Documents (Voice Recorder):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 Electro-Voice ZLX-BRKT Installation manual electro-voice/zlx-brkt-9AZ.pdf 14 Jan 2024 12
2 Gigabyte GA-VT890P Operation & user’s manual gigabyte/ga-vt890p-K57.pdf 04 Nov 2022 96
3 iSmartAlarm CubeOne Quick installation manual ismartalarm/cubeone-YN8.pdf 23 Aug 2023 4
4 Singer 14K11 Instructions for using and adjusting singer/14k11-T5P.pdf 10 Nov 2022 5 0.19 Mb
5 NUUO Titan Operation & user’s manual nuuo/titan-F17.pdf 20 Jun 2022 85
6 Sony PMC-DR45 - Personal Component System Operating instructions manual sony/pmc-dr45-personal-component-system-E29.pdf 22 Oct 2022 48

Similar Resources:

  • Olympus

    VN-5000

    (2 pages)
    -1--2--3--4--5-h Uso del cordónEstado de la grabadora Funcionamiento Pantalla En modo de parada Pulse y mantenga plsado el botón STOP (4 )El número total de archivos grabados en la carpeta y el tiempo de grabación remanente aparecen en la pantallaEn modo de grabaciónPulse el botón DISP/MENUCada vez que pulsa el botón DISP/MENU, la pantalla cambia entr …
  • Philips

    DVDR5520H

    (118 pages)
    HDD & DVD Player / RecorderDVDR5520H / DVDR5570HPremium Home ServiceThis product comes withRefer to the inside page for details.Read your Quick Start Guide and/or User Manual rst for quick tipsthat make using your Philips product more enjoyable.Register your product and get support at www.philips.com/welcomeUser ManualDownloaded From Disc-Player.com …
  • FLIR

    M4100 Series

    (2 pages)
    Information in this document is subject to change without notice. As our products are subject to continuous improvement, FLIR Systems, Inc. and our subsidiaries reserve the right to modify product design, specifications and prices, without notice and without incurring any obligation. E&OE © 2016 FLIR Systems, Inc. All rights reserved.Package Contents: …
  • metasoft

    FonTel L1USB

    (16 pages)
    metasoftPHONE CALL RECORDERFonTelInstallation manualApplies to the recorders: • FonTel L1USB• FonTel L2USB• FonTel L4USB• FonTel ISDN• FonTel L4NET• FonTel VoIP(last updated: 1-07-2013)CMETASOFT s.c.ul. Saperów 21/1A53-151 Wrocław, Polandphone: +48 71 350 05 23fax: +48 71 350 05 96www. fontel.eu info@ fontel.eu …
  • Gemark

    101

    (11 pages)
    PnoTo FACT' FolJ""e)cE-HHCa rsbv,yO4-sdeou3"@;GENERAL INFORMATIONThe Gemark Model l0l tape recorder is a two-speed tape recorder designed to play andrecord two iracks of material on standard-width recording tape.Recordings may be made from a phonograph, radio, or television receiver as well asthose rnade from the microphone.3eET:vOXReel …
  • Toho Electronics

    TRM-00J

    (49 pages)
    DWG.No. 4B-6829-A TOHO ELECTRONICS INC. Operation Manual (Communication Edition) (TOHO Protocol, MODBUS) Model: TRM-00J Name: Paperless Recorder …

Comments, Questions and Opinions: