Manualios.com

Alpine CDA-7846E Owner's Manual

Alpine CDA-7846E Manual Online:

3.65, 691 votes
Alpine CDA-7846E User Manual
Alpine CDA-7846E User Guide
Alpine CDA-7846E Online Manual

Text of Alpine CDA-7846E User Guide:

  • Alpine CDA-7846E, 54 English Specifications FM TUNER SECTION Tuning Range ......................................................................................................87.5 – 108.0 MHz Mono Usable Sensitivity .......................................................................... 9.3 dBf (0.8µV/75 ohms) 50 dB Quieting Sensitivity ...................................................................... 13.5 dBf (1.3µV/75 ohms) Alternate Channel Selectivity ................................................................................................. 80 dB Signal-to-Noise Ratio .........................................................................................................

  • Alpine CDA-7846E, 24 English Radio Operation Storing into Direct Access Preset (D.A.P.) Band A combination of radio stations in any band, AM and FM (up to 6 stations) can be manually preset onto the D.A.P. band. Press the F3 button when the "FUNC" indicator is on. Press the BAND button to select FM or AM. The selected band will be displayed. To memorize stations onto the D.A.P. band, follow the steps for the automatic or Manual Storing of Station Presets section above. Note: When Automatic Memory Preset is used with D.A.P., 4 FM and 2 AM stations will be stored in Presets 1 – 4 and 5 �

  • 26 English Radio Operation 1 Displaying Station Titles If a title has been entered for the selected station, it can be displayed in place of the frequency. The display will toggle between the frequency and title display with each press of the TITLE button. (Refer to page 27 to title stations.) NORMAL Mode CLOCK PRIORITY Mode STATION TITLE Mode Title not entered Title entered Charact

  • Alpine CDA-7846E, 32 English CD Operation 1 2 Normal Play and Pause Insert a CD into the CD player. The CD player begins playback from the first track on the disc. The display shows the track number and elasped time of the track being played. When the last track is played back the player returns to the first track and begins playback from that point. If a CD is already loaded in the CD player, press the SOURCE button to select the CD mode. Note: * The source indicator varies depending on the connected source. Press the (Play/Pause) button during the play mode to place the player in the Pause mode. "PAUSE" appears in the display. To resume play

  • 35 English CD Operation M.I.X. (Random Play) Press the F3 button in the play or pause mode. The M.I.X. indicator will illuminate and the tracks on the disc will be played back in a random sequence. After all the tracks on the disc have been played back once, the player will begin a new random sequence play until the M.I.X. mode is canceled. To cancel M.I.X.

  • 40 English CD Operation 1 4 5 2 3 Erasing Disc Title Press the TITLE button to select the disc titling mode. Then, press and hold for at least 2 seconds. Press and hold the FUNC button for at least 2 seconds to activate the title scanning mode. The title in the display will blink, for example "ALPINE". Press the ( ) DN or UP ( ) button repeatedly until the

  • Alpine CDA-7846E, 11 English Basic Operation 1 Non Fading Pre-Out (N.F.P.) On and Off Press and hold the PWR button for at least 2 seconds. Press the F1 button. With each press, N.F.P. is toggled On or Off. N.F.P. ON: In this position, the Front Pre- Output will not be affected by the fader. This is ideal for driving a subwoofer amplifier. N.F.P. OFF:Returns to normal fader mode. Note: Set the N.F.P. to OFF unless the subwoofer is used. Press the PWR button to set the selected mode. PWR INTLZ PWR INTLZ 2 N.F.P. ON N.F.P. OFF F1 3

  • Alpine CDA-7846E, 6 English Precautions Installation Location Make sure the CDA-7846E player/receiver will not be exposed to: • Direct sun and heat • High humidity • Excessive dust • Excessive vibrations Handling the Detachable Front Panel • Do not expose to rain or water. • Do not drop or apply shock.

  • Alpine CDA-7846E, 14 English Basic Operation Adjusting Display Contrast You can adjust the display contrast for better visibility. Press and hold the PWR button for at least 2 seconds. Press the F3 button. The "CONTRAST" is displayed. Press the or button to adjust the contrast of the display. You can adjust in a range of –6 and +6. The initial setting at the factory is "0". Press the PWR button to set the selected mode. PWR INTLZ 1 2 F3 3 DN UP PWR INTLZ CONTRAST 0 4

  • 23 Réception radio English Radio Operation 1 2 3 Automatic Memory of Station Presets Press the SOURCE button to select the radio mode. Press the BAND button repeatedly until the desired radio band is displayed. Press and hold the A. ME button for at least 2 seconds. The frequency on the display continues to change while the automatic memory is in progress. The tuner will automatica

  • Alpine CDA-7846E, 51 English In Case of Difficulty Radio Mode Symptom Unable to receive stations. Unable to tune stations in the seek mode. Broadcast is noisy. Cause and Solution • No antenna or open connection in cable. – Make sure the antenna is properly connected; replace the antenna or cable if necessary. • You are in a weak signal area. – Make sure the tuner is in the DX mode. • If the area you are in is not known to be a weak signal area, the antenna may not be grounded and connected properly. – Check your antenna connections; make

  • Alpine CDA-7846E, 43 English CD Shuttle Operation Searching Titled Discs (Title Search Menu) Press the TITLE button to activate the Title Display mode. Press and hold the T.S.M. button for at least 2 seconds while the title is displayed. The title in memory blinks in the display. Press the ( ) DN or UP ( ) button to select the desired disc title. Press the T.S.M. button to play the selected disc. The unit will automatically search the disc and will play that disc. 1 3 2 4 TITLE CLK BAND T.S.M. BAND T.S.M. ALPINE DN UP

  • Alpine CDA-7846E, 7 English 1 Detaching the Front Panel Press the PWR (Power) button to turn off the power. Press the RLS (release) button until the front panel pops out. Grasp the left side of the front panel and pull it out. Notes: • The front panel may become hot (especially the connector terminals), this is not malfunction. • To protect the front panel, place it in the supplied carrying case. Attaching the Front Panel 1. First, insert the right side of the front panel into the main unit. Align the 2 small holes on the front panel with the 2 pr

  • Alpine CDA-7846E, 37 English CD Operation 1 NORMAL Mode CLOCK PRIORITY Mode CD TITLE Mode Title not entered To Display CD Titles After a title has been entered for a CD, it can be displayed by pressing the TITLE button. The display will toggle between Normal, Clock and CD Title with each press of the TITLE button (see example below). (Refer to page 38 to title the disc.) Title entered Characters and Symbols 11'03 T08 12:58 T08 ALPINE A (a) B (b) C (c) D (d) E (e) F (f) G (g) H (h) I (i) K (k) L (l) M (m) N (n) O (o) P (p) Q (q) R (r) S (s) U (u) V (v) W (w) X (x) Y (y) Z (z) 0 1 2 4567

  • Alpine CDA-7846E, 44 English CD Shuttle Operation Multi-Changer Selection Alpine’s Ai-NET system will support up to 6 CD Shuttles. When operating two or more changers, the KCA-400C (Multi-Changer Switching device) must be used. If you use 1 Switching device, you can connect up to 4 CD Shuttles. If you use 2 Switching devices, you can connect up to 6 CD Shuttles. Press the SOURCE button on the CDA-7846E to activate the CD Changer mode. Alternatively, press the SOURCE button on the Remote Controller (RUE-4185) to activate the CD Shuttle mode. Proceed to Step below to select the desired CD Shuttle. Press the BAND button on the CDA-7846E or the RUE-4185 to activate the

  • Alpine CDA-7846E, 41 English CD Shuttle Operation Controlling CD Shuttle (Optional) An optional 6-disc or 12-disc CD Shuttle may be connected to the CDA-7846E if it is Ai-NET compatible. With a CD Shuttle connected to the Ai-NET input of the CDA-7846E, the CD Shuttle will be controllable from CDA-7846E. Using the KCA-400C (the Multi-Changer Switching device) multiple changers can be controlled by the CDA-7846E. See the Multi-Changer Selection section on page 44 for selecting the CD Shuttles. Notes: • The controls on the CDA-7846E for CD Shuttle operation are operative only when a CD Shuttle is connected. • The "CHG" indicator illuminates in the CD Shuttle mode. Press the S

  • Alpine CDA-7846E, 9 English Basic Operation 1 1 Turning Power On and Off Press the PWR button to turn off the unit. The volume level gradually increases to the previous level you were listening to before the unit was turned off. Press the PWR button again to turn off the unit. PWR INTLZ Turning Loudness On/Off Loudness introduces a special low- and high- frequency emphasis at low listening levels. This compensates for the ear's decreased sensitivity to bass and treble sound. Press and hold the LOUD button for at l

  • Alpine CDA-7846E, 47 English Remote Control 8 Button Radio mode: SEEK (DN) Button CD/CD Shuttle mode: Press the button to go back to the beginning of the current track. 9 Button Radio mode: SEEK (UP) Button CD/CD Shuttle mode: Press the button to advance to the beginning of the next track. Ä Button Radio mode: Pressing the button will select, in descending order, stations programmed into the radio's presets as shown below. CD/CD Shuttle mode: DISC Select (DN) Button Press the button to select a disc in descending order. Å Audio Processor Button** Press the button to call the external audio processor mode.* Ç Audio Select Button Press to select the audio source

  • Alpine CDA-7846E, 8 English Basic Operation Initial System Start-Up 1 When operating the unit for the first time after installation or after the vehicle's battery has been disconnected and reconnected, set the volume level to its minimum, then remove the detachable front panel. (Refer to page 7.) Press the button with a ball-point pen or any other pointed object. The plate opens automatically. There is a small hole at the lower right side. Behind this hole the red Reset switch is located. Press the Reset switch with a ball-point pen or any other pointed object. Push the plate to close it until a click sound is produced. Attach the front panel (see page 7). 2 3 4 5

  • Alpine CDA-7846E, 52 English CD Mode In Case of Difficulty Symptom CD insertion not possible. Unable to Fast-Forward or Backward. Sound skips due to vibration. Sound skips without vibration. Cause and Solution • There is a CD already in the transport. – Eject the CD in transport and remove it. • The CD is being improperly inserted. – Make sure the CD is being inserted per instruction in the Owner's Manual. • The CD has been damaged. – Eject the CD and discard; using a damaged CD in your unit can cause damage to the transport. • Improper mounting. – Securely re-mount the unit. • Disc is very dirty. – Clean the disc. • Disc has scratches. – Change the disc.

  • Alpine CDA-7846E, 22 English Radio Operation 1 Manual Storing of Station Presets 1. Tune in the desired radio station you wish to store in the preset memory. 2. Check that the "FUNC" indicator is off. 3. Press and hold any one of the preset buttons (1 through 6) for at least 2 seconds. The frequency display will begin to blink. 4. Press the preset button into which you wish to store the station while the display is blinking (within 5 seconds). The display stops blinking to indicate that the station has been memorized. The preset number is also displayed. 5. Repeat the procedure to store 5 other stations onto the same band. Use this procedure for other bands. A total

  • 48 English Remote Control Battery Replacement Applicable battery: Use two "AAA" sized dry batteries or equivalent. Opening the battery cover Slide out the battery cover while firmly pressing outward. Replacing the battery Put the batteries in the case as illustrated. Closing the cover Push the cover as illustrated until a click is heard.

  • Alpine CDA-7846E, 28 English Radio Operation 6 5 Titling Stations (Continued) Press the TITLE button to store the first character. The first character will stop blinking and the display will automatically advance to the next character. When that character begins to blink, you may choose the next letter or symbol of your title. Repeat the steps – above to complete the titling. All 10 character positions should be filled. Use spaces where characters are not needed (for example at the end of a 5 character title, use 5 spaces to complete the title). After the las

  • Alpine CDA-7846E, 34 English CD Operation 1 Repeat Play Press the F4 button to play back repeatedly the track being played. The RPT indicator appears and the track will be played repeatedly. Press the F4 button again to deactivate the repeat play. Note: * If a CD Shuttle is connected and the RPT ALL mode is selected, the unit repeatedly plays back all tracks on the disc selected. Notes: In case of 6-disc CD Shuttle connected: • Press the "FUNC" button to illuminate the "FUNC" (Function) indicator and go to step . In case of 12-disc CD Shuttle connected: • Press the "FUNC" button twice to illuminate the "FUNC&quo

  • Alpine CDA-7846E, 3 English Contents Page 4 .......................................................................................... Precautions 7 ...................................................................... Detachable Front Panel Basic Operation 8 ........................................................................... Initial System Start-up 9 .................................................................... Turning Power On and Off 9 ...................................................................... Turning

  • Alpine CDA-7846E, 46 English Remote Control Controls 1 Mute Button Press the button to lower the volume by 20 dB instantly. Press the button again to cancel. 2 Power Switch Press the switch to turn the power on/off. 3 Button Press the button to switch between the Play and Pause modes for the CD. 4 CD Changer Button Press the button to change to the CD Shuttle operation. 5 Band/Program Button Radio mode: BAND Button Press the button and the band will change as shown below. 6 Volume Adjustment Buttons To increase the volume level..... Press the button To decrease the volume level..... Press the but

  • Alpine CDA-7846E, 33 English CD Operation 1 Music Sensor (Skip) Momentarily press the ( ) DN button once to return to the beginning of the current track. If you wish to access a track further back, repeatedly press until you reach the desired track. (The example shows the Music Sensor operation starting from track No. 4.) Press the UP ( ) button once to advance to the beginning of the next track. If you wish to access a track further ahead, press repeatedly until the desired track is reached. Note: The music sensor feature is functional in the play or pause mode. DN UP CD T04 CD T04 CD T03 CD T04 CD T05

  • Alpine CDA-7846E, 31 English CD Operation Removing Disc Press the OPEN button to open the front door. Press the Eject ( ) button on the top side of the front door. The CD is automatically ejected half way out. Remove the CD with your hand. Note: If the CD is not removed for several seconds, the player automatically draws the CD into the compartment to protect the CD. Close the front door with your hand until you hear a click sound. 1 2 3 OPEN

  • Alpine CDA-7846E, 19 English Basic Operation 1 2 FUNC F1 F2 F3 F4 F5 F6 Mode Function indicator (on/ off) Radio Preset 1 P–DN (Preset DOWN) P–UP (Preset UP) D.A.P. (Direct Access Memory Preset) MONO (Stereo/Monaural) T.RCL (Tuner Recall) MUTE D–DN (Disc DOWN) D–UP (Disc UP) M.I.X. (Randam Play) RPT (Repeat) SCAN MUTE D–DN (Disc DOWN) D–UP (Disc UP) M.I.X. (Randam Play) RPT (Repeat) SCAN MUTE Hour Adjustment (HOUR) Minute Adjust- ment (MIN) Time Signal Adjust- ment (CT) M.I.X. (Randam Play) RPT (Repeat) SCAN MUTE Preset 2 Preset 3 Preset 4 Preset 5 Pres

Related Products and Documents (Car Stereo System):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 BenQ GL950M Operation & user’s manual benq/gl950m-568.pdf 06 Nov 2022 49 3.34 Mb
2 Samsung CQ1570-B Owner's manual samsung/cq1570-b-M89.pdf 26 Nov 2022 48
3 Sanyo SR-6100K Instruction manual sanyo/sr-6100k-UW2.pdf 03 Mar 2023 2 0.08 Mb
4 Sanyo PLC-XT10 Service manual sanyo/plc-xt10-NY3.pdf 13 Apr 2023 50
5 GMC 1998 Sonoma Owner's manual gmc/1998-sonoma-X45.pdf 20 Oct 2023 406 21.72 Mb
6 JUKI MEB-3810 Instruction manual juki/meb-3810-R68.pdf 20 Jun 2023 106

Similar Resources:

  • Pioneer

    DEH-P4500R

    (8 pages)
    INSTALLATION MANUALMANUEL D’INSTALLATION<KMMNX/02H00000>DEH-P4500RPrinted in ThailandImprimé en Thaïlande<CRD3696-A/JS> EWThis product conforms to new cord colors.Los colores de los cables de este producto se confor-man con un nuevo código de colores.Dieses Produkt entspricht den neuen kabelfarben.Le code de couleur des câbles utilisé pour …
  • Kenwood

    KRC-578R

    (19 pages)
    EJECTPWROFFTILOUDVOL ADJMENUDISPNAME.SSCAN B.S/RDM REPD.SCNM.RDMDISCDISCPROG/PTYDABAUDKRC-578R45W 4XEJECTPWROFFTILOUDVOL ADJMENUDISPNAME.SSCAN B.S/RDM REPD.SCNDISCDISCPROG/PTYDABAUDB NRMTL/M.RDMKRC-680R45W 4XKRC-578R/RYKRC-680RCASSETTE RECEIVERSERVICE MANUALC 2000-3 PRINTED IN KOREAB51-7598-00 ( K ) 2202Front glass assy(B10-3206-08)Escutcheon assy(B07-21 …
  • Sony

    CDX-GT550UI - Fm/am Compact Disc Player

    (2 pages)
    Notes on the control and power supply leadsThe power antenna (aerial) control lead (blue) supplies +12 V DC when you turn on the tuner.When your car has built-in FM/AM antenna (aerial) in the rear/side glass, connect the power antenna (aerial) control lead (blue) or the accessory power supply lead (red) to the power terminal of the existing anten …
  • Baby Jogger

    Car Stereo System

    (2 pages)
    Chicco Car Seat Adaptor for Elite/Classic/Summit Double StrollersThe Chicco Car Seat Adaptor for Double Strollers is designed to be used with your Baby Jogger City Mini, City Micro, City Series, City Classic, City Elite, Summit 360, or Summit XC double stroller and your Chicco car seat. This car seat adaptor is only compatible with this car seat and these st …
  • Metra Electronics

    99-9305

    (8 pages)
    INSTALLATION INSTRUCTIONS FOR PART 99-9305Flat Blade Screwdriver • Phillips Screwdriver • Drill 1-800-221-0932 www.metraonline.comKIT FEATURES© COPYRIGHT 2004-2010 METRA ELECTRONICS CORPORATION• ISO DIN Head Unit Provision A) Radio Housing • B) ISO Brackets • C) (4) Phillips Screws • D) (4) Phillips ISO Screws KI …
  • Panasonic

    CQCB9900U - AUTO RADIO/CD DECK

    (4 pages)
    Removable Full Front MP3 WMA CD Player/Receiver with Full Dot Matrix Display and CD Changer ControlCQ-CB9900U≥ Please read these instructions carefully before using this product and save this manual for future use.Operating Instructions …

Car Stereo System Instructions:

Comments, Questions and Opinions: