Siemens SINAUT MD720-3 System Manual
|
SINAUT MD720-3 in Terminal Mode SINAUT MD720-3 44 C79000-G8976-C211 <mem3>. AT+CNUM Subscriber number Test Command: AT+CNUM=? Response: OK Executive command Command: AT+CNUM Response: +CNUM: [<alpha1>],<number1>,<type1>[,<speed>,<service>[,<itc>]] [<CR><LF>+CNUM: [<alpha2>],<number2>,
Siemens SINAUT MD720-3, SINAUT MD720-3 C79000-G8976-C211 71 Technical Data 7 Function GPRS connections to SINAUT MICRO SC GSM data calls (CSD 9.600 bps) MTC SMS sending Standard RS232 (V.24 / V.28), socket: D-SUB 9 pins Default speed 9600 bps Interface X1 Control AT commands GSM module GPRS / CSD / Quad band GPRS Up to 2 uplinks / up to 4 downlinks (max. 5 Slots) Transmit power GSM 850 MHz (max. 2W), GSM 900 MHz (max. 2W), DCS 1800 MHz (max. 1W), PCS 1900 MHz (max. 1W) Air interface Antenna connector SMA / 50 Ohm power consumption typ. 5.5W Supply voltage 12 - 30 VDC (24 VDC nominal) Power supply S
Siemens SINAUT MD720-3, Service functions SINAUT MD720-3 C79000-G8976-C211 65 6.2 Getting the current settings and values Connect your PC to the interface X1 and start a terminal software, e.g. HyperTerminal. Select the used COM interface of the PC and configure the character format and the baudrate to the same settings as the X1 interface of the SINAUT MD720-3. By factory default the SINAUT MD720-3 has the following settings: Baudrate 9600 Bit/s (in OPC Mode) or 19200 Bit/s (in Terminal Mode) Cha
Siemens SINAUT MD720-3, SINAUT MD720-3 in Terminal Mode SINAUT MD720-3 38 C79000-G8976-C211 AT+CPIN Enter PIN Test Command: AT+CPIN=? Response: OK Read command Command: AT+CPIN? Response: +CPIN: <code> Executive command Command: AT+CPIN=<pin> [,<newpin>] Response: OK Parameter: <code>: Values reserved by this device: READY Device is not pending for any password SIM PIN Device is waiting SIM PIN to be given SIM PUK Device is waiting SIM PUK to be given. Also, a second pin, <newpin>, is used to replace the old pin in the SIM
Siemens SINAUT MD720-3, SINAUT MD720-3 in Terminal Mode SINAUT MD720-3 C79000-G8976-C211 41 Notice: The execute command specifies PDP context parameter values for a PDP context identified by the (local) context identification parameter, <cid>. The number of PDP contexts that may be in a defined state at the same time is given by the range returned by the test command. A special form of the set command, +CGDCONT= <cid> causes the values for context number <cid> to become undefined. AT+CGATT GPRS Attach
Siemens SINAUT MD720-3, SINAUT MD720-3 in Terminal Mode SINAUT MD720-3 56 C79000-G8976-C211 AT+KHNDVR Selecting mobile / stationary operation Read command Command: + KHNDVR? Response: + KHNDVR <stat> Executive command Command: + KHNDVR=<stat> Response: OK Parameter: <stat>: 0: Setting for data calls (CSD 9600 Bit/s) in mobile operation 1: Setting for data calls (CSD 9600 Bit/s) in stationary operation Notice: The command has no impact to GPRS connections or the sending of SMS. In mobile operation <stat> must be set to
Siemens SINAUT MD720-3, SINAUT MD720-3 in Terminal Mode SINAUT MD720-3 C79000-G8976-C211 25 4.4 Terminal mode operation To operate the device the PIN (PIN = Personnel Identification Number) of the inserted SIM card must be known. In the Terminal Mode the PIN is not stored in the SINAUT MD720-3. The PIN must be set again every time the device is turned- on. ● The PIN is set by AT commands. If you use a PIN-less SIM card the PIN request is skipped. Control by the application Usually the application or the application software, which you execute on a connected computer, will control the SINAUT MD720-
Siemens SINAUT MD720-3, SINAUT MD720-3 in Terminal Mode SINAUT MD720-3 34 C79000-G8976-C211 AT\Q Hardware Flow Control on/off Executive command Command: AT\Q<n> Response OK Parameter: <n>: 0: Hardware Flow Control (RTS/CTS) off 3: Hardware Flow Control (RTS/CTS) on Notice: - ATX Set CONNECT result code Format und Call monitoring Executive command Command: ATX[<value>] Response: OK Parameter: <value>: 0 : CONNECT result code only returned, dial tone and busy detection are both disable
SINAUT MD720-3 in Terminal Mode SINAUT MD720-3 28 C79000-G8976-C211 4.6 Use AT commands Syntax The AT command language is a standard for controlling modems. It is line- orientated. Each command line begins with AT (for ATtention), followed by the actual command, and ends with (Enter key). Example: ATD444444¬ means: dial (D for Dial) 444444 There are only two exc
Siemens SINAUT MD720-3, SINAUT MD720-3 in Terminal Mode SINAUT MD720-3 46 C79000-G8976-C211 AT+CBST Select bearer service type Read command Command: AT+CBST=? Response: +CBST: (list of supported <speed>s),(list of supported <name>s),(list of sup- ported <ce>s) OK Executive command Command: AT+CBST=[<speed> [,<name>[,<ce>]]] Response: OK Parameter: <speed>: 4 2400 bps (V.22bis) 6 4800 bps (V.32) 7 9600 bps (V.32) 68 2400 bps (V.110 or X.31 flag stuffing) 70 4800 bps (V.110 or X.31 flag stuffing) 71 9600 bps (V.110 or X.31 flag stuffing) <name>: 0 data circuit asynchronous (UDI or 3
Siemens SINAUT MD720-3, SINAUT MD720-3 in Terminal Mode SINAUT MD720-3 C79000-G8976-C211 37 AT+CRLP Radio link protocol Test Command: +CRLP=? Response: +CRLP: (list of supported <iws>s),(list of supported <mws>s), (list of supported <T1>s),(list of supported <N2>s),<ver1> ,(list of supported <T4>s) Read command Command: +CRLP? Response: +CRLP: <iws>,<mws>,<T1>,<N2>,<ver1>,<T4> Executive command Command: AT+CRLP=<iws>[,<mws>[,<T1>
Siemens SINAUT MD720-3, SINAUT MD720-3 in Terminal Mode SINAUT MD720-3 42 C79000-G8976-C211 AT+CPAS Phone activity status Test Command: AT+CPAS=? Response: +CPAS: (list of supported <pas>s) OK Read command Command: AT+CPAS Response: +CPAS: <pas> OK Parameter: <pas>: 0 ready (device allows commands from application) 1 unavailable (device does not allow commands from application) 2 unknown (device is not guaranteed to respond to instructions) 3 ringing (device is ready for commands from
SINAUT MD720-3 C79000-G8976-C211 23 SINAUT MD720-3 in Terminal Mode 4 In the Terminal Mode the SINAUT MD720-3 operates like a GSM modem, which is controlled by AT commands. Supported are • incoming and outgoing GSM data connections with 9600 bps with modems being connected to the GSM network, the ISDN or the analogue telephone network, �
Siemens SINAUT MD720-3, SINAUT MD720-3 in Terminal Mode SINAUT MD720-3 C79000-G8976-C211 27 The LED S (status) blinks fast If the modem blinks fast (4 times each second), either the SIM card was not detected correctly or the SIM card is PUK-blocked, because a wrong PIN has been entered too often. Please check, if the SIM card is inserted correctly (see chapter 2 Inserting the SIM card). Please check, if the SIM card is PUK-blocked. Insert the SIM card into a common mobile phone. The mobile phone will display, if the SIM card is PUK-blocked. If the SIM card is PUK-blocked, please enter the PUK and then a PIN. Yo
Siemens SINAUT MD720-3, SINAUT MD720-3 in Terminal Mode SINAUT MD720-3 30 C79000-G8976-C211 4.7 Supported AT commands in Terminal Mode All AT commands being not listed below will be answered with OK by the device, but the command will not be executed. +++ Switch from data mode to command mode Execute command Command: +++ Response: This command is only available during data calls. The +++ characters sequence causes to cancel de data flow over the AT interface and switch to command mode. This allows to enter AT commands while maintaining the dat
Siemens SINAUT MD720-3, Technical Data SINAUT MD720-3 72 C79000-G8976-C211 Supply current / no connection or connection to SINAUT MICRO SC without data exchange In 90mA at 12V In 50mA at 24V In 40mA at 30V Temperature range Operation: –20°C up to +60°C Storage: –25°C up to +85°C Ambient conditions Humidity 0-95 %, not condensing Construction Top-hat rail housing Material Synthetic material Protection category IP40 Dimensions 114 mm x 22,5 mm x 99 mm (L x W x H) Mechanics Weight Approx. 150g CE Yes R&TTE Yes EMV /
Siemens SINAUT MD720-3, SINAUT MD720-3 in Terminal Mode SINAUT MD720-3 C79000-G8976-C211 35 AT&D Set circuit Data Terminal Ready (DTR) function mode Executive command Command: AT&D[<value>] Response: OK Parameter: <value>: 0: Device ignores status on DTR. <Default> 2: ON->OFF on DTR: Disconnect call, change to command mode. During state DTR = OFF is auto-answer off. Notice: - AT&F Restore manufactory configuration Executive command Command: AT&F Response: OK Parameter: <value>: 0: Restore parameters to manuf
Siemens SINAUT MD720-3, Service functions SINAUT MD720-3 66 C79000-G8976-C211 6.3 Service mode to upload a new firmware When the service mode is active you can update the firmware of SINAUT MD720- 3. The firmware contains the fundamental programming of the SINAUT MD720-3. If the manufacturer has produced new firmware, for example to equip the device with new functions, then this can be loaded into the SINAUT MD720-3. You can find the latest firmware in the internet on the pages of des Siemens Service & Support (see Foreword). To update the firmware please proceed as follows. Switch on the service mode and connect the device to a PC 1. Push the SET button
Siemens SINAUT MD720-3, SINAUT MD720-3 C79000-G8976-C211 9 Contents Preface.......................................................................................................................................... 7 1 Introduction................................................................................................................... 11 2 Inserting the SIM card .................................................................................................. 13 3 Connecting the device and switching on the device................................................ 19 4 SINAUT MD720-3 in Terminal Mode..................................................................
Siemens SINAUT MD720-3, SINAUT MD720-3 C79000-G8976-C211 75 Glossary GSM Global System for Mobile Communication Global standard for wireless telephony, data and fax transmission and transmission of text messages (SMS). GSM based networks are available in a lot of countries world-wide, with high coverage in Europe, China, Latin America as well as in regions of the USA, Africa and Russia. Depending on the used frequencies you distinguish PCS 850MHz, GSM 900MHz, DCS 1800MHz und PCS 1900MHz networks. CSD Circuit Switched Data GSM Service for wireless data transmission at 9600 bps full duplex. Connections can be established to other GSM devices, to analogue modems
Siemens C2-010 Modem Operation & user’s manual
C2-010 |
Siemens Gigaset SX685 WiMAX Modem Quick start manual
Gigaset SX685 WiMAX |
Siemens Simatic S7-300 Modem Installation manual
Simatic S7-300 |
Siemens Simatic S7-300 Modem Installation and operating manual
Simatic S7-300 |
Siemens Simatic S7-300 Modem Operation & user’s manual
Simatic S7-300 |
Siemens Simatic S7-300 Modem Technical data manual
Simatic S7-300 |
Siemens SINAUT ST7 Modem System manual
SINAUT ST7 |
Siemens MC35 Modem Command set
MC35 |
# | Manufacturer | Model | Document Type | File | Updated | Pages | Size |
---|---|---|---|---|---|---|---|
1 | Oregon Scientific | Electronic Learning Aid Tote N' Teach | Instruction manual | oregon-scientific/electronic-learning-aid-tote-n-teach-364.pdf | 28 Jun 2023 | 19 | |
2 | Lexmark | 6500e | Operation & user’s manual | lexmark/6500e-W6Y.pdf | 22 Nov 2023 | 123 | |
3 | Winnebago | Vista | Operation & user’s manual | winnebago/vista-1V8.pdf | 19 Sep 2023 | 173 | |
4 | Andis | PM-1 120V | Specification | andis/pm-1-120v-UZO.pdf | 24 Aug 2023 | 2 | 2.03 Mb |
5 | Breville | the Tea Maker BTM800XL | Instruction book | breville/the-tea-maker-btm800xl-3A2.pdf | 30 Nov 2022 | 72 | 3.29 Mb |
6 | Philips | SA3RGA04K | Brochure | philips/sa3rga04k-3PJ.pdf | 21 Sep 2023 | 3 |
Moxa Technologies
– 1 – – 2 – – 3 – - 4 - P/N: 1802031000014 OnCell G3100 Quick Installation Guide Fourth Edition, April 2014 Overview There are currently six models in the OnCell G3100 series of IP-gateways: the OnCell G3110, OnCell G3150, OnCell G3110-HSPA, and OnCell G3150-HSPA. The main difference between the models is the serial interface type and cellu …
OnCell G3100 Series(2 pages) |
3Com
® 3C OM I MPACT ISDN E XTERNAL D IGITAL M ODEM Q UICK S TART I NSTRUCTIONS Part Number 09-0700-002The following information will help you install the 3Com Impact ISDN External digital modem models 3C871, 3C872, 3C876, or 3C877. Refer to the 3Com Impact ISDN External Digital Modem User Guide for additional information. Site Preparation T …
3C871(15 pages) |
Mycricket
www.mycricket.com1 Table of ContentsContentsBEFORE USING UM185C .........................................2About this User Manual ................................................................................................... 3Product Overview .......................................................................................................... …
UM185C(38 pages) |
Multitech
1MultiMobileMT5634ZLXI/EPRODUCT UPDATEPN 82086600, REV. AThe MT5634ZLXI/E is the International version of the MT5634ZLX/E card, with the addition of global telecom approvals. Thisproduct is local-government approved in many countries in Europe, the Americas, Asia, Australia, and other regions of theworld. This document covers the differences in the ins …
MT5634ZLXI/E(4 pages) |
Robustel
Robustel GoRugged M1000 XP Quick Guide RT_QG_M1000 XP_v.1.0.0 24.01.2014 1 / 5 Robustel GoRugged M1000 XP Quick Guide Chapter 1. Interface Introduction 1.1 Overview 1.2 LED Indicators After inserting the SIM card into the modem and power on, the LED indicators’ status should be as follow when work normally: Name Status RUN System is running norma …
GoRugged M1000 XP(5 pages) |
INOR
Inor Process ABPO Box 9125SE-200 39 MALMÖSwedenPhone: +46-(0)40-31 25 60E-mail: [email protected] The current list of all INOR contacts and addressescan be found at: www.inor.com © INOR 03/2018 - 4006766001 - QS ICON-BT - R01 enSubject to change without notice.Included: • ICON-BT• USB-cable• Batteries• User instructionICON-BT KitArt. Nr. 70CFGBT0 …
ICON-BT(2 pages) |
Graham Field Bathroom Aid LUMEX 89101Guide: Graham Field LUMEX 89101 (HN32BG, Upd.01/09/2023) LUMEX 89101, 1 |
Planex Wireless Router BLW-54MRPlanex BLW-54MR User Guide (Operation & user’s manual), @3E85YQ BLW-54MR, 102 |
3Com Network Router -16233Com -1623 Network Router Getting started -1623, 39 |
Tripp Lite Extender Wireless Console Extender B014-000Extender PDF Owner's manual Wireless Console Extender B014-000, 32 |
Sedna Media Player SE-3360MP-NSedna Media Player SE-3360MP-N Operation & user’s manual SE-3360MP-N, 13 |
eta Kitchen Appliances 161eta Kitchen Appliances 161 User manual manual 161, 44 |
HP Printer 6940 seriesPrinter PDF Setup poster 6940 series, 2 |
Pentax Digital Camera 120MIPentax Digital Camera Operation & user’s manual (File: pentax-120mi-operation-user-s-manual-44, 18/01/2024) 120MI, 44 |
Exposure Bicycle Accessories Flash FlareExposure Bicycle Accessories Manual (File: exposure-flash-flare-manual-1, 23.01.2024) Flash Flare, 1 |
DSC Security System MAXSYS PC4020#I52C94: MAXSYS PC4020 Security System Instruction manual MAXSYS PC4020, 40 |
Control Company Timer TRACEABLEControl Company TRACEABLE User Guide (Instructions), @72ZRXP TRACEABLE, 2 |
RCA MP3 Player Lyra RD2201RCA Lyra RD2201 Manual (Doc Type: MP3 Player Operation & user’s manual) Lyra RD2201, 40 |