Whirlpool WHESCS Installation And Operation Manual

Text of Whirlpool WHESCS User Guide:

• Whirlpool WHESCS, 6 PLUMBING CODES All plumbing must be completed in accordance with national, state and local plumbing codes. LAUNDRY TUBSTANDPIPE 1-1/2” air gap FLOOR DRAIN In the state of Massachusetts: The Commonwealth of Massachusetts plumbing code 248-CMR shall be adhered to. A licensed plumber shall be used for this installation. AIR GAP REQUIREMENTS A drain is needed for regeneration water (See Figure 2). A floor drain, close to the water softener, is pre- ferred. A laundry tub, standpipe, etc. are other drain options. Secure valve drain hose in place. Leave an air gap of 1-1/2” between the end of the hose and the d

• 7349641 (Rev. C 3/20/17) Manufactured and warranted by Ecodyne Water Systems 1890 Woodlane Drive Woodbury, MN 55125 How to install, operate and maintain your Demand Controlled Water Softener Do not return water softener to store System tested and certified by the Water Quality Association against CSA B483.1. If you have any questions or concerns when installing, operating or maintaining your w

• Whirlpool WHESCS, 7 Installation Requirements VALVE DRAIN REQUIREMENTS Using the flexible drain hose (included), measure and cut to the length needed. Flexible drain hose is not allowed in all localities (check your plumbing codes). If local codes do not allow use of a flexible drain hose, a rigid valve drain run must be used. Purchase a com- pression fitting (1/4 NPT x 1/2 in. minimum tube) and 1/2" tubing from your local hardware store. Plumb a rigid drain as needed (See Figure 5). NOTE: Make the valve drain line as short and direct as possible.

• Whirlpool WHESCS, 5 Packing List Inspect Shipment Drain HoseBypass Valve Clips Adaptor Elbow Installation Adaptors FIG. 1 Hose Clamps Grommet O-rings Water Hardness Test Strip Water Conditioning Information IRON Iron in water can cause stains on clothing and plumb- ing fixtures. It can negatively affect the taste of food, drinking water, and other beverages. Iron in water is measured in parts per million (ppm). The total* ppm of iron, and type or types*, is determined by chemical analysis. Four different types of iron in water are: = Ferrous (clear water) iron = Ferric (red water) iron = Bacterial and organically bound iron = Colloidal and inorganically bound iron (fe

• Whirlpool WHESCS, 17 Efficiency Icon In the state of California: You must turn the Salt Efficiency Fea ture ON. This may initiate more frequent recharges. However, it will operate at 4,000 grains per pound of salt or higher. Customizing Features / Options POWER OUTAGE MEMORY If electrical power to the water softener is lost, “mem- ory'' built into the timer circuitry will keep all settings for several hours. While the power is out, the display is blank and the water softener will not regenerate. When electrical power is restored, the following will occur: Reset the present time only if the display is flashing. The HARDNESS and RECHARGE TIME never require resetting unless a change is desire

• Whirlpool WHESCS, 19 Routine Maintenance FIG. 36 Broom Handle Pencil Mark 1” - 2” Salt Salt Bridge Water Level Push Tool into Salt Bridge to Break FIG. 37 Cap O-ring Seal Screen Support Screen Gasket *Flow Plug (HVDC) Housing Ferrule Nut Cone Screen *Flow Plug *Install with lettered side up, concave side down. CLEANING THE NOZZLE & VENTURI A clean nozzle & venturi (See Figure 37) is a necessity for the water softener to work properly. This small component creates the suction to move brine from the brine tank, into the resin tank. If it should become p

• Whirlpool WHESCS, 11 Excessive Weight Hazard Use two or more people to move and lift salt bags. Failure to do so can result in back or other injury. ADD WATER AND SALT TO THE SALT STOR AGE TANK Installation Instructions TEST FOR LEAKS To prevent air pressure in the water softener and p lumbing system, complete the following steps in order: 1. Fully open two or more softened cold water faucets close to the water softener, located downstream from the water softener. 2. Place the bypass valve (single or 3 valve) into the "bypass&

• Whirlpool WHESCS, 13 Programming the Water Softener FIG. 18 2. If you want to change the recharge start time, press the r UP or s DOWN buttons until the desired time shows. Be sure AM or PM is correct. SET SALT TYPE 1. Press the PROGRAM button once again to display a flashing “nACL”. 2. Press the r UP or s DOWN buttons to set your water’s hardness number. NOTE: If your water supply contains iron, compen- sate for it by adding to the water hardness number. For example, assume your water is 20 gpg hard and contains 2 ppm iron. Add 5 to the hardness number for each 1 ppm of iron. In this example, you would use 30 for your hardness number.

• Whirlpool WHESCS, 18 Customizing Features / Options b etween recharges may be set from 1 to 15 days, as follows: NOTE: The softener will recharge on its own if need- e d, even if it is before the set number of days. 1. Press and hold the PROGRAM button until the s creen in Figure 32 is displayed. Once in this dis- play, press the PROGRAM button four times and the display in Figure 34 is shown. 2. Press the r UP or s DOWN buttons to set the number of days. 3. Press the PROGRAM button two times to return to the normal time of day screen. 12 OR 24 HOUR CLOCK All time displays are shown in standard clock time (AM and PM) at the 12 hour default setting. If 24 hour clock displays are desired, follow steps

• 3 Specifications & Performance Claims Questions? Call Toll Free 1-866-986-3223 Monday- Friday, 8 AM - 7 PM EST or visit www.whirlpoolwatersofteners.com When you call, please be prepared to provide the model and serial number, found on the rating decal, typically located on the rim below the salt lid hinges. *Capacity to reduce clear water iron is substantiate

• Whirlpool WHESCS, 10 Installation Instructions COMPLETE INLET AND OUTLET PLUMBING Measure, cut, and loosely assemble pipe and fittings from the main water pipe to the inlet and outlet ports of t he water softener valve. Be sure to keep fittings fully together, and pipes squared and straight. Be sure hard water supply pipe goes to the water sof- tener valve inlet side. NOTE: Inlet and outlet are marked on the water softener valve. Trace the water flow direction to be sure hard water is to inlet. IMPORTANT: Be sure to fit, align and support all plumb- ing to prevent putting stress on the water softener valve inle

• Whirlpool WHESCS, 20 Troubleshooting While an error code appears in the display, all buttons are inoperable except the PROGRAM button. PRO- GRAM remains operational so the service person can perform the Manual Advance Diagnostics, see below, to further isolate the problem. FIG. 40 FIG. 39 5. While in this diagnostic screen, the following infor- mation is available and may be beneficial for vari- ous reasons. This information is retained by the computer from the first time electrical power is applied to the electronic controller.

• 4 Water Softener Safety Your safety and the safety of others are very important. We have provided many safety messages in this manual and on your appliance. Always read and obey all safety m essages. This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others.

• 8 Installation Instructions TYPICAL INSTALLATION FIG. 9 NOTE: See “Air Gap Requirements” section. NOTE: Water Softener shown with Salt Lid and Top Cover removed Inlet Outlet Clips Pipe To Outside Faucets 1” NPT Sweat Adaptor (not included) O-ring Single Bypass Valve Lubricated O-ring Conditioned Water Hard Water M ain Wa te r Pip e Water Softener Valv

• Whirlpool WHESCS, 9 MOVE THE WATER SOFTENER INTO PLACE 1. Move the water softener into the desired location. Set it on a solid, level surface. IMPORTANT: Do not place shims directly under the salt storage tank to level the softener. The weight of the tank, when full of water and salt, may cause the tank to fracture at the shim. 2. Visually check and remove any debris from the water softener valve inlet and outlet ports. 3. Make sure the turbine assembly spins freely in the "out" port of the valve. 4. If not already done, put a light coating of silicone grease on the single bypass valve o-rings. 5. Push the single bypass valve into the softener valve as far as it w

More Instructions:

Whirlpool WHESCS Installation and operation manual 20-04-2023 18

DOWNLOAD

Related Products and Documents (Water Dispenser):

Comparable Devices:

Similar Resources:

• USTM WS-12-C-1650 (16 pages) Instrukcja obsługi stacji zmiękczającychИнструкция обслуживания умягчителяPLENRUWater soener manual instruction.....2.....6.....11 …

• DVA AL (68 pages) D.M. 174/2004RIF. 02/18ALAL 5AL 8AL 12Manuale d’istruzioniInstruction ManualNotice d’UtilisationHandbuchManual de IstruccionesVolumetricoVolumetricVolumétriqueVolumetrischVolumétricoAL …

• Aqua Medic Reef 2000 (58 pages) 1Riff 2000 Bedienungsanleitung D 6-stufiges Wasseraufbereitungssystem für Riffaquarien bis 1.500 l. Mit dem Kauf dieses Filtersystems haben Sie sich für ein Qualitätsprodukt entschieden. Es ist speziell für den aquaristischen Gebrauch entwickelt worden und wurde von Fachleuten erprobt. Mit diesem System sind Sie bei …

• Kenmore 625 (7 pages) OWNER'SMANUALMODEL NO.625.344800CAUTIONREAD THIS MANUALCAREFULLYBEFORE YOU USE YOURPURIFIERIF YOU HAVE ANYQUESTIONS ABOUT THISPRODUCT CALLTOLL- FREE1 - 800 - 426 - 9345www.KenmoreWater.comSAVE THISMANUALKenmore CountertopWater Purifier- HOW IT WORKS -- CARE OF -- REPAIR PARTS -Sears, Roebuck and Co., Hoffman Estates, IL 60179 USA7270818 (Rev. B 11/3/04) …

• Manitowoc K00099 (1 pages) K00099/K00150 WATER FILTER BIN BRACKET Installation Instructions 1. Water filter bin bracket can be used to mount all Tri-liminator water filter assemblies on either side or back of any Manitowoc ice bin. 2. Remove foam tape from area where bracket is to be mounted, hang bracket, and install foam tape, provided with kit, over top of brack …

• Spectrum MixH2O-PRO (17 pages) Table of Contents1. General Notes p.22. Description & Equipment Adjustments p.33. Components, Features & Functions p.44. Component Contents p.55. Valve User Interface p.66. Installation Instructions p.87. Valve Programming Set-up p.108. Troubleshooting p.139. Cautions p.1510. Technical Information …

Comments, Questions and Opinions: