Manualios.com

Z Corporation zprinter 450 Quick Start Manual

Z Corporation zprinter 450 Manual Online:

3.9, 2161 votes
Z Corporation zprinter 450 User Manual
Z Corporation zprinter 450 User Guide
Z Corporation zprinter 450 Online Manual

Text of Z Corporation zprinter 450 User Guide:

  • Z Corporation zprinter 450, 9/25/09 ZPRINTER ® 350 ZPRINTER ® 450 QUICK START GUIDE Part Number 09569 Rev. D

  • 2 zcentral.zcorp.com Overview - ZPrinter 350/ZPrinter 450 Build Chamber Binder Cartridge Debris Separator Vacuum Hose Fast Axis Deck Service Station Top Cover Control Panel Air Wand Heater (450 only) Build Bed Arm Holes Glove Box (450 only) Control KnobLCD Display Fine Powder Removal Chamber Parking Caps (450 only)

  • Z Corporation zprinter 450, zcentral.zcorp.com 3 Push the Control Knob once to: • Bring up the printer menu. • Select a menu command. • Start/Stop/Cancel a menu function. Turn the Control Knob left/right to highlight menu items. When selecting the Raise/Lower Platform commands, hold the Control Knob down to raise/lower the platform. Rear View External Connections Power Switch Nameplate (Serial Number) Power Cord Connection External Connections Network Connection (Ethernet RJ-45)

  • Z Corporation zprinter 450, 4 zcentral.zcorp.com Welcome To The ZPrinter ® 350/ ZPrinter ® 450 Quick Start Guide This Guide is intended as a handy reference for users who are familiar with their 3D printer and just need to print a part. The Guide assumes that: • The ZPrinter is properly installed and running, and that no errors are displayed on the ZPrinter control panel. • The ZPrint™ Software is installed and running, and is config- ured properly for your printer and choice of powder. For ZPrint installation instructions, see the ZPrint™ Software Manual. • The pri

  • Z Corporation zprinter 450, zcentral.zcorp.com 5 2. Check The Printer Before you start your print job, it’s important that you check the printer. A clean, well-maintained printer produces better parts, has less downtime, and needs fewer service calls. 1. Check for loose powder in or around the Build Bed, Fast Axis, and Deck. If you need to clean these areas, follow the steps in Section 6.1, “Vacuum Up Excess Powder”. 2. Check that the Debris Separator, the Rails and Carriage, the Service Station and Parking Caps are clean. If any of these need cleaning, follow the procedures in these sections: • Section 6.2, “Empty The Debris Separator” • Section 6.3,

  • Z Corporation zprinter 450, 6 zcentral.zcorp.com 3. Setup Your Build And Print Now that your printer is clean, you need to open up the 3D file using ZPrint, and select your printing parameters. 1. Open your file in ZPrint. 2. Select File > 3D Print Setup, or click on the Toolbar., to open the 3D Print Setup dialog. 3. Check your printer settings to be sure the correct printer and powder are displayed. • If you need to change any settings, refer to the Setup and Print the Build section of the Hardware Manual for your printer. 4. Select File > 3D Print, or click on the Toolb

  • Z Corporation zprinter 450, zcentral.zcorp.com 7 4. Gross Powder Removal When the build is finished, you will need to remove the powder around the part. 4.1 Automatic Powder Removal (ZPrinter 450 only) When the build is finished, the printer starts an automatic, heated drying cycle. A counter on the printer LCD counts down the time remaining before the part is dry. After the drying cycle completes, the printer automatically removes excess powder by vibrating the Build Bed and vacuuming through the bottom of the Build Bed. Remove the part and carefully transfer it to the F

  • Z Corporation zprinter 450, 8 zcentral.zcorp.com 6. Routine Cleaning After Every Build After every build, it is important to clean your printer following the steps below. A clean, well-maintained printer produces better parts, has less downtime, and needs fewer service calls. Routine cleaning includes the following steps: • Vacuum Up Excess Powder • Empty The Debris Separator • Clean The Rails and Carriage • Clean The Service Station • Clean the Parking Caps (ZPrinter 450 only) 6.1 Vacuum Up Excess Powder Vacuum

  • zcentral.zcorp.com 9 6.4 Clean The Service Station Before you begin: • Get several dry paper towels and a cotton swab. • Get the squirt bottle filled with distilled water. • Wear disposable gloves. • Get the Pick and Syringe from the Accessories Kit. 1. Open the printer top cover and the Service Station cover. 2. Place paper towels around th

  • Z Corporation zprinter 450, 10 zcentral.zcorp.com 6.5 Clean the Parking Caps (ZPrinter 450 only) Before you begin: • Get several dry paper towels and a cotton swab. • Get the squirt bottle filled with distilled water. • Wear disposable gloves. • Get the Pick and Syringe from the Accessories Kit. 1. Lift the Parking Cap cover to a horizontal position and place dry paper towels underneath. 2. Squirt the distilled water onto the caps. Do not squirt water onto the Build Bed. 3. Use a cotton swab and dry paper towel to wipe the caps clean. Use the pick if needed to remove any powder. 4. Remove the paper towels from under the caps and wipe up any excess water on the

  • zcentral.zcorp.com 11 7. Post-Processing With Z-Bond For complete instructions, refer to the Hardware Manual for your printer, or to our 3D User Web site at zcentral.zcorp.com. 7.1 Preparation • Ensure the part is both completely dry and completely free of loose powder. • Wear a lab coat or smock, safety glasses, and a pair of hig

  • Z Corporation zprinter 450, 12 zcentral.zcorp.com 8. Replace a Print Head For more details on performing these steps, refer to the Addi- tional Operations section of the Hardware Manual for your printer. 1. On the Control Panel select BUILD CHAMBER, then LOWER PLATFORM. Lower the build platform about 6 inches below the top. 2. Select PRINT HEAD then CHANGE PRINT HEAD on the LCD menu. The fast axis moves to the service position. 3. Open the printer top cover. Open the carriage cover and lift the print head out of its slot. Properly recycle or dispose of the e

  • Z Corporation zprinter 450, zcentral.zcorp.com 13 Where To Go For More Information About Your Printer For additional information, consult the ZPrinter® 350 (or 450) Hardware Manual. These are found on the CD that was shipped with your printer. They are also available through the Help function of ZPrint. About ZPrint Software For additional information, consult the ZPrint™ Software Man- ual. This is found on the CD that was shipped with your printer. It is also available through the Help function of ZPrint All the printer and softwa

  • Z Corporation zprinter 450, 14 zcentral.zcorp.com Notices Copyright © Z Corporation 1995-2009. All rights reserved. The information in this document may not be duplicated or transmitted in any way without the express written consent of Z Corporation. The information contained herein is for the use of Z Corporation customers, who are permitted to create brief excerpts for the purposes of training and review. This informa- tion may not be incorporated in any commercial programs, books, databases, or in any kind of software without the co

  • Z Corporation zprinter 450, zcentral.zcorp.com 15 Z Corporation Contact Information: If you have any questions about your 3D Printer or the ZPrint/ZEdit Software, please contact your local Reseller/ Service Provider. If they are unable to help, contact us directly. United States (Corporate Headquarters) 32 Second Avenue Burlington, MA 01803 USA Phone: +1-781-852-5005 Fax: +1-781-852-5100 Service: Phone: +1-781-852-5050 Fax: +1-781-852-5055 E-mail: [email protected] Denmark Z Corporation Svanevang 2 DK-3450 Alleroed Denmark Phone: +45 48 14 11 22 Japan/ Hong Kong Z Corporation Yok

Related Products and Documents (3D Printers):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 Maytag MEC4436AAC - Chrome 36 Inch Electric Cooktop Parts list maytag/mec4436aac-chrome-36-inch-electric-cooktop-VLR.pdf 01 Jan 2024 3
2 Zanussi ZWA 385 Instruction manual zanussi/zwa-385-7ML.pdf 27 Oct 2023 16 1.56 Mb
3 Sunforce 33805 Manual  sunforce/33805-8VJ.pdf 10 Aug 2023 1
4 Pantum M6550 series Operation & user’s manual pantum/m6550-series-PV5.pdf 08 Aug 2022 122
5 Toshiba Carrier RAS-09 Installation manual toshiba/carrier-ras-09-721.pdf 27 Dec 2023 14 1.84 Mb
6 Transition Networks E-CX-MC22 Operation & user’s manual transition-networks/e-cx-mc22-K62.pdf 04 Jul 2023 1 0.03 Mb

Similar Resources:

  • Raise3D

    PRO2 Series

    (5 pages)
    WWW.RAISE3D.COM AMERICA · ASIA · EUROPE Pro2 Endstop Limit Switch Board Installation Instruction Pro2 Endstop Limit Switch Board Installation Instruction STEP 1: The Locations of Endstop Boards Z-Endstop Board X-Endstop Board Y-Endstop Board …
  • TRAK

    3ntr Series

    (192 pages)
    TRAK® 3ntr 3D Printers Printer & MMS Guide Covers Current Models: • 3ntr A2 • 3ntr A4 • MMS v2 2615 Homestead Place Rancho Dominguez, CA 90220-5610 USA T | 310.608.4422 | F | 310.764.2668 Service Department: 800.367.3165 e-mail: [email protected] | [email protected] | web: www.trakmt.com Docu …
  • Raise3D

    PRO2 Series

    (8 pages)
    Manual Pro2 Series - How to Install Extruder Side Cooling Fan -v1.0* The steps of replacing both sides of cooling fans are similar with each other. Here we usethe right side as reference. 1. PreparationUnload the filament from both nozzles. Turn off the printer after filament being removed. 2. Remove Fan DuctRemove the screws marked in the picture below and …
  • Rokit

    3DSION PRO

    (37 pages)
    Think!Make!Touch!Multiple perfection, Desktop 3D Printer EDISON PROUSER MANUALThis User Manual is designed to help you start your experience with 3DSION PRO. In order to achieve great results, you will need to experiment and tinker. That’s why it’s so crucial to take the time to learn about your new machine. In this User Manual, you will learn the basics …
  • Creality

    Dual Z

    (38 pages)
    (Demo unit shown, may not reflect final product) Ender Extender™ 5 Installation Guide for Dual Z, XL and Dual Z XL kits www.enderextender.com 4/21/21 …
  • Creality 3D

    Ender-3 Pro

    (12 pages)
    V.2.2Ender-3 Pro Series 3D Printer[ To make Top-quality 3D printer]To be the Chief Evangelist◆ This guide is for the Ender-3 Pro Series of 3D printers.◆ Select the correct input voltage to match your local mains (230V or 115V)◆ Because of software/hardware upgrades and model differences, new revisions may not be listed in this guide.◆ Please plug …

Comments, Questions and Opinions: