Aluratek WMQ137AM Quick Installation Manual

Text of Aluratek WMQ137AM User Guide:

• Aluratek WMQ137AM, Quick Installation Guide 1. Get Start Installation Connect the 3G Wireless Router to Your Network Note: DO NOT connect 3G Mobile Router to power before performing the installation steps below. Step1. Attach the antenna. 1.1. Remove the antenna from its plastic wrapper. 1.2. Screw the antenna in a clockwise direction to the back panel of the unit. 1.3. Once secured, position the antenna upward at its connecting joint. This will ensure optimal reception. Step2.

• Aluratek WMQ137AM, Insert your either Type II 3G card (either 16-bit or 32-bit ) or plug USB 3G Modem to router Note: The 3G Mobile Router is designed to work with either UMTS or EV-DO and even HSUPA 3G modem. Please refer to your service provider for detailed feature information. Step3. Insert the Ethernet patch cable into LAN Port on the back panel of the 3G Mobile Router, and an available Ethernet port on the network adapter in the computer you will use to configure the unit. Note:

• Aluratek WMQ137AM, Step 4. 4.1. Connect the power adapter to the receptor on the back panel of your 3G Mobile Router. 4.2. Then plug the other end of the power adapter into a wall outlet or power strip. a. The Power LED will turn ON to indicate power has been applied. b. Other LEDs will flash ON and OFF as the 3G Mobile Router performs initialization and Internet connection processes. This will take a few minutes. c. When complete, the following LEDs will illuminate green: 3G, WAN, LAN, and WiFi.

• 2. Using the Easy Setup Utility 1. Install the Easy Setup Utility from CD. After the installation is finished, you can execute it by the shortcut. 2. Configure the settings by the following steps. 2.1 Select Language then click “Next” for continues. 2.2. Setup mode. You can select Quick mode to run the setup step-by-step or run advanced mode to d

• 2.8 Test WAN Networking service. Click “ Next” for continue. 2.9 Setup Completed. You can open the default web browser to configure advanced settings of the router . Click “ Finish” to complete the installation.

More Instructions:

	Aluratek WMQ137AM Product reference sheet 06-08-2023 1	DOWNLOAD
	Aluratek WMQ137AM Operation & user’s manual 13-06-2023 47	DOWNLOAD
	Aluratek WMQ137AM Product reference card 26-06-2023 1	DOWNLOAD

Related Products and Documents (Network Router):

Comparable Devices:

Similar Resources:

• Digicom VoiceGATE Plus Wireless ADSL Router (2 pages) For further information visit ourwebsite http://www.digicom.itVoiceGATE Plus 26/08/2008 Wireless ADSL Router with VoIP functionalitiesVoiceGATE Plusl ADSL 2/2+ up to 24 Mbpsl SIP 2.0 Standard VoIP supportl 2 FXS portslWEBbasedlocalandremotecongurationDESCRIPTIONVoiceGATE Plus is an ADSL Router with built-in VoIP, Wireless and Firewall …

• 4RF Aprisa LTE (7 pages) Quick Start Guide Contents Follow these steps to operate your Aprisa LTE router: 1. Check the box contents 2. Install the Aprisa LTE and connect the protection earth 3. Set up and apply power to the Aprisa LTE 4. Connect to the Aprisa LTE 5. Configure the Aprisa LTE 6. Test the Aprisa LTE operation …

• TP-Link TL-WR710N (2 pages) 150Mbps Wireless N Mini Pocket Router - Advanced EditionMODEL NO. TL-WR710NPackage ContentsQIG150Mbps Wireless N Mini Pocket Router - Advanced EditionMODEL NO. TL-WR710NResource CD for User Guide OnlyEthernet CableTL-WR710NQuick Installation Guide150Mbps TL-WR710N7106504219 REV1.0.0Instant Wireless ConnectionPhysical DescriptionBefore hardware connectio …

• Polycom SoundPoint IP 500 (31 pages) PLEASE READ This manual is from the manufacturer—GoTo Connect may not support some features discussed in this document. Please see our online documentation for a complete list of supported features. Thanks for choosing us! …

• Hirschmann RS20 (284 pages) Basic ConfigurationRelease 6.0 07/2010Technical [email protected] ManualBasic ConfigurationIndustrial ETHERNET (Gigabit) Switch RS20/RS30/RS40, MS20/MS30, OCTOPUS, PowerMICE, RSR20/RSR30, MACH 100, MACH 1000, MACH 4000 …

• Samsung Techwin SPN-10050 (2 pages) ENGLISHSWITCH SETUPSET-UP AND CONFIGURATION PROBLEMS1. WHAT TO DO IF THE POWER LED IS NOT LIT UP?Check if the power adapter is properly connected to a wall socket and the back of the SPN-10050.2. WHAT TO DO IF A CONNECTED DEVICE IS NOT DETECTED?using a different LAN cable.CONNECTING THE POWER ADAPTER Plug the power adapter into a free wall socket, then …

Comments, Questions and Opinions: