Manualios.com

AMX NXA-ENET8-POE+ Instruction Manual

AMX NXA-ENET8-POE+ Manual Online:

4.85, 1285 votes
AMX NXA-ENET8-POE+ User Manual
AMX NXA-ENET8-POE+ User Guide
AMX NXA-ENET8-POE+ Online Manual

Text of AMX NXA-ENET8-POE+ User Guide:

  • AMX NXA-ENET8-POE+, Table o f Con te nts 13 Instruction Manual - NXA-ENET8-POE+ Creating SNMP Notification Logs........................................................................................................ 221 Command Usage............................................................................................................................................... 221 Showing SNMP Statistics .................................................................................................................... 222 Remote Monitoring...........................................................................................

  • AMX NXA-ENET8-POE+, Congestion Control 118 Instruction Manual - NXA-ENET8-POE+ Storm Control Use the Traffic > Storm Control page to configure broadcast, multicast, and unknown unicast storm control thresholds. Traffic storms may occur when a device on your network is malfunctioning, or if application programs are not well designed or properly configured. If there is too much traffic on your network, performance can be severely degraded or everything can come to complete halt. You can protect your network from traffic stor

  • AMX NXA-ENET8-POE+, Multicast Filtering 249 Instruction Manual - NXA-ENET8-POE+ MLD Snooping (Snooping and Query for IPv4) Multicast Listener Discovery (MLD) snooping operates on IPv6 traffic and performs a similar function to IGMP snooping for IPv4. That is, MLD snooping dynamically configures switch ports to limit IPv6 multicast traffic so that it is forwarded only to ports with users that want to receive it. This reduces the flooding of IPv6 multicast packets in the specified VLANs. There are two versions of the MLD protocol, version 1 and version 2. MLDv1 control packets include Listener Query, Listener Report, and Listener Done messages (equivalent to IGMPv2 query, repo

  • AMX NXA-ENET8-POE+, Multicast Filtering 243 Instruction Manual - NXA-ENET8-POE+ Displaying Multicast Groups Discovered by IGMP Snooping Use the Multicast > IGMP Snooping > Forwarding Entry page to display the forwarding entries learned through IGMP Snooping. Command Usage To display information about multicast groups, IGMP Snooping must first be enabled on the switch (see page 234). The following table lists the options on this page: To show multicast groups learned through IGMP snooping, click Multicast > IGMP Snooping > Forwarding Entry. Displaying I

  • Multicast Filtering 234 Instruction Manual - NXA-ENET8-POE+ Only IGMPv3 hosts can request service from a specific multicast source. When downstream hosts request service from a specific source for a multicast service, these sources are all placed in the Include list, and traffic is forwarded to the hosts from each of these sources. IGMPv3 hosts may also request that service be forwarded f

  • AMX NXA-ENET8-POE+, Basic Management Tasks 51 Instruction Manual - NXA-ENET8-POE+ Specifying NTP Authentication Keys Use the System > Time (Configure Time Server - Add NTP Authentication Key) page to add an entry to the authentication key list. The following table displays the options on this page: Perform these steps to add an entry to NTP authentication key list: 1. Click System > Time. 2. Select Conf igure Time Server from the Step list. 3. Select Add NTP Authentication Key from the Action list. 4. Enter the index number and MD5 authentication key s

  • AMX NXA-ENET8-POE+, Basic Administration Protocols 214 Instruction Manual - NXA-ENET8-POE+ Perform these steps to configure an SNMP group: 1. Click Administration > SNMP. 2. Select Conf igure Group from the Step list. 3. Select Add from the Action list. 4. Enter a group name, assign a security model and level, and then select read, write, and notify views. 5. Click Apply. Perform these steps to show SNMP groups: 1. Click Administration > SNMP. 2. Select Conf igure Group from the Step list. 3. Select Show from the Action list. Setting Community Access Strings Use the Administration > SNMP (Configure Community - Add) p

  • Interface Configuration 67 Instruction Manual - NXA-ENET8-POE+ Perform these steps to configure a periodic sample of statistics: 1. Click Interface > Port > Statistics, or Interface > Trunk > Statistics. 2. Select Add from the Action menu. 3. Select an interface from the Port or Trunk list. 4. Enter the sample name, the interval, and the number of buckets requested. 5. Cl

  • AMX NXA-ENET8-POE+, Multicast Filtering 239 Instruction Manual - NXA-ENET8-POE+ Perform these steps to show the static interfaces assigned to a multicast service: 1. Click Multicast > IGMP Snooping > IGMP Member. 2. Select Show Static Member from the Action list. 3. Select the VLAN for which to display this information. Setting IGMP Snooping Status per Interface Use the Multicast > IGMP Snooping > Interface (Configure VLAN) page to configure IGMP snooping attributes for a VLAN. To configure snooping globally, refer to the Configuring IGMP Snooping and Query Parameters section on page 234. Command Usage Multicas

  • AMX NXA-ENET8-POE+, Security Measures 167 Instruction Manual - NXA-ENET8-POE+ ARP Inspection ARP Inspection is a security feature that validates the MAC Address bindings for Address Resolution Protocol packets. It provides protection against ARP traffic with invalid MAC-to-IP address bindings, which forms the basis for certain "man-in-the-middle" attacks. This is accomplished by intercepting all ARP requests and responses and verifying each of these packets before the local ARP cache is updated or the packet is forwarded to the appropriate destination. Invalid ARP packets are dropped. ARP Inspection determines the validity of an ARP packet based on valid IP

  • AMX NXA-ENET8-POE+, Security Measures 151 Instruction Manual - NXA-ENET8-POE+ Replacing the Default Secure-site Certificate Use the Security > HTTPS (Copy Certificate) page to replace the default secure-site certificate. When you log onto the web interface using HTTPS (for secure access), a Secure Sockets Layer (SSL) certificate appears for the switch. By default, the certificate that the web browser displays will be associated with a warning that the site is not recognized as a secure site. This is because the certificate has not been signed by an approved certification authority. If you want this warning to be replaced by a message confirming t

  • AMX NXA-ENET8-POE+, Security Measures 156 Instruction Manual - NXA-ENET8-POE+ Access Control Lists Access Control Lists (ACL) provide packet filtering for IPv4/IPv6 frames (based on address, protocol, Layer 4 protocol port number or TCP control code), IPv6 frames (based on address, DSCP traffic class, or next header type), or any frames (based on MAC address or Ethernet type). To filter incoming packets, first create an access list, add the required rules, and then bind the list to a specific port. Configuring Access Control Lists - An ACL is a sequential list of permit or deny conditions that apply to IP addresses, MAC

  • AMX NXA-ENET8-POE+, IP Configuration 270 Instruction Manual - NXA-ENET8-POE+ Perform these steps to configure general IPv6 settings for the switch: 1. Click System > IPv6 Conf iguration. 2. Select Conf igure Interface from the Action list. 3. Specify the VLAN to configure. 4. Enable address auto-configuration, or enable IPv6 explicitly to automatically configure a link-local address and enable IPv6 on the selected interface. (To manually configure the link-local address, use the Add IPv6 Address page.) Set the MTU size, the maximum number of duplicate address detection messages, the neighbor solicitatio

  • AMX NXA-ENET8-POE+, Quality of Service 129 Instruction Manual - NXA-ENET8-POE+ Perform these steps to configure a policy map: 1. Click Traff ic > DiffServ. 2. Select Conf igure Policy from the Step list. 3. Select Add from the Action list. 4. Enter a policy name. 5. Enter a description. 6. Click Apply. Perform these steps to show the configured policy maps: 1. Click Traff ic > DiffServ. 2. Select Conf igure Policy from the Step list. 3. Select Show from the Action list. Perform these steps to edit the rules for a policy map: 1. Click Traff ic > DiffServ. 2. Select Conf igure Policy from the Step list. 3. Select Add Rule from the Action list. 4. Select the name of a policy map. 5. Click

  • AMX NXA-ENET8-POE+, Security Measures 159 Instruction Manual - NXA-ENET8-POE+ Perform these steps to add rules to an IPv4 Standard ACL: 1. Click Security > ACL. 2. Select Conf igure ACL from the Step list. 3. Select Add Rule from the Action list. 4. Select IP Standard from the Type list. 5. Select the name of an ACL from the Name list. 6. Specify the action (i.e., Permit or Deny). 7. Select the address type (Any, Host, or IP). If you select Host, enter a specific address. If you select IP, enter a subnet address and the mask for an address range. 8.

  • AMX NXA-ENET8-POE+, Quality of Service 127 Instruction Manual - NXA-ENET8-POE+ Perform these steps to edit the rules for a class map: 1. Click Traff ic > DiffServ. 2. Select Conf igure Class from the Step list. 3. Select Add Rule from the Action list. 4. Select the name of a class map. 5. Specify type of traffic for this class based on an access list, DSCP or IP Precedence value, VLAN, or CoS value. You can specify up to 16 items to match when assigning ingress traffic to a class map. 6. Click Apply. Perform these steps to show the rules for a class map: 1. Click Traff ic >

  • Basic Administration Protocols 231 Instruction Manual - NXA-ENET8-POE+ LBD Conf iguration The switch can be configured to detect general loopback conditions caused by hardware problems or faulty protocol settings. When enabled, a control frame is transmitted on the participating ports, and the switch monitors inbound traffic to see if the frame is looped back. Usage Guidelines The defaul

  • Quality of Service 130 Instruction Manual - NXA-ENET8-POE+ Perform these steps to show the rules for a policy map: 1. Click Traff ic > DiffServ. 2. Select Conf igure Policy from the Step list. 3. Select Show Rule from the Action list. Attaching a Policy Map to a Port Use the Traffic > DiffServ (Configure Interface) page to bind a policy map to a port. Command Usage First define a class

  • AMX NXA-ENET8-POE+, Interface Configuration 73 Instruction Manual - NXA-ENET8-POE+ Perform these steps to display trunk connection parameters: 1. Click Interface > Tru nk > Static. 2. Select Conf igure General from the Step list. 3. Select Show Information from the Action list. Conf iguring a Dynamic Trunk Use the Interface > Trunk > Dynamic pages to set the administrative key for an aggregation group, enable LACP on a port, configure protocol parameters for local and partner ports, or to set Ethernet connection parameters. Command Usage To avoid creating a loop in the netwo

  • AMX NXA-ENET8-POE+, Security Measures 140 Instruction Manual - NXA-ENET8-POE+ Perform these steps to show the accounting method applied to various service types and the assigned server group: 1. Click Security > AAA > Accounting. 2. Select Configure Method from the Step list. 3. Select Show from the Action list. Perform these steps to configure the accounting method applied to specific interfaces, console commands entered at specific privilege levels, and local console, Telnet, or SSH connections: 1. Click Security > AAA > Acco

  • AMX NXA-ENET8-POE+, Basic Administration Protocols 187 Instruction Manual - NXA-ENET8-POE+ Basic Administration Protocols This chapter describes basic administration tasks including: Event Logging - Sets conditions for logging event messages to system memory or flash memory, configures conditions for sending trap messages to remote log servers, and configures trap reporting to remote hosts using Simple Mail Transfer Protocol (SMTP). Link Layer Discovery Protocol (LLDP) - Configures advertisement of basic information about the local switch, or discovery of information about neighboring de

Related Products and Documents (Network Router):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 Takeuchi TB128FR Operator's manual takeuchi/tb128fr-M82.pdf 10 Jan 2023 215
2 Panasonic DVD-S54 Operating instructions manual panasonic/dvd-s54-4PS.pdf 11 Aug 2023 28 3.97 Mb
3 Virgin i2001 Operation & user’s manual virgin/i2001-M8E.pdf 13 Nov 2022 8 0.18 Mb
4 Asus P4GE-MX Operation & user’s manual asus/p4ge-mx-69D.pdf 21 Jul 2023 62 2.56 Mb
5 Shure LEGENDARY PERFORMANCE MV88 Operation & user’s manual shure/legendary-performance-mv88-NP1.pdf 09 Nov 2023 120
6 Nilfisk-ALTO CONTRACTOR DIESEL Instruction manual nilfisk-alto/contractor-diesel-Q35.pdf 24 May 2023 16

Similar Resources:

  • H3C

    MSR810

    (8 pages)
    H3C MSR 810 & 2600 & 3600 Routers Comware 7 OAA Configuration Guide New H3C Technologies Co., Ltd. http://www.h3c.com Software version: MSR-CMW710-R0809 Document version: 6W400-20200823 …
  • YORKVILLE

    LP-C12

    (14 pages)
    U.S.A.Yorkville Sound Inc.4625 Witmer Industrial EstateNiagara Falls, New York14305 USAVoice: (716) 297-2920Fax: (716) 297-3689WORLD HEADQUARTERSWEB ACCESS: http://www.yorkville.comCANADAYorkville Sound550 Granite CourtPickering, OntarioL1W-3Y8 CANADAVoice: (905) 837-8481Fax: (905) 837-8746Quality and Innovation Since 1963Printed in CanadaSERVICE MANUALLP-C1 …
  • Zoom

    X7N

    (8 pages)
    X7N QUICK START This Quick Start describes how to connect the X7N to one or more computers or other devices. First the X7N is configured using a computer; and then the X7N is connected to one or more computers or other devices. More detailed information, including information using the X7N for online gaming, is in the User Manual on the CD. Package Cont …
  • NETGEAR

    GS110EMX

    (2 pages)
    Installation Guide1. Register With the NETGEAR Insight AppUse the NETGEAR Insight app to register your switch, activate your warranty, and access support.1. On your iOS or Android mobile device or tablet, visit the app store, search for NETGEAR Insight, and download the latest version of the app.2. Open the NETGEAR Insight app.3. If you did not set up a N …
  • NetComm

    NF10W

    (7 pages)
    Page 1 of 7User GuideNetComm NF10W Wireless ADSL2+ Modem Router©2016 ACN Inc. All rights reserved ACN Pacic Pty Ltd ABN 85 108 535 708 Customer Service 1300 881 778 acnpacic.comMKT-3024 28.1 …
  • Cypress Semiconductor

    West Bridge Astoria AN46860

    (4 pages)
    Schematic Review Checklist for West Bridge® Astoria™ December 12, 2008 Document No. 001-46860 Rev. *A 1 AN46860 Author: Praveen Kumar Associated Project: No Software Version: Astoria SDK 1.0 Associated Application Notes: None Application Note Abstract West Bridge® Astoria™ is a USB and mass storage peripheral control device that co …

Comments, Questions and Opinions: