Beam 9602 Installation & User Manual
|
Beam 9602, www.beamcommunications.com 12 9602 SBD Modem | Installation and User Manual Installing the USB Drivers The following driver installation procedure is only required if using the USB port on the 9602 SBD Modem. It is not required if only using the 9-way serial port. The 9602 SBD Modem uses an FTDI device internally to provide the serial communications. Windows 7 will automatically search for and install the correct drivers. Windows XP will require that the drivers be installed from the included CD. If not already done so, connect a USB cable between the modem and your PC and ensure the LED is ON. After a short time the following screen will appear. Select No, not
Beam 9602, www.beamcommunications.com 18 9602 SBD Modem | Installation and User Manual DTR - Active low handshaking input AT&Dn controls how the 9602 SBD MODEM uses DTR: If set to AT&D0, DTR is always ignored. Otherwise DTR set to OFF places the data port into UART test mode after 10 seconds, or immediately on bootup. A subsequent transition of DTR to ON returns the data port to DCE mode and resets it to its power-on state. The UART test mode is provided for factory testing of the data port UART. An FA should never activate test mode; if it does, the 9602 SBD MODEM will stop responding to AT commands until the data port is returned to DCE mode. DSR - Active l
Beam 9602, 9602 SBD Modem | Installation and User Manual 5 Equipment Overview 1. USB mini-B Port 2. SMA Antenna Jack 3. LED Indicator 4. 14 pin Connector 5. SMA to TNC Adaptor 6. Mounting Bracket Cable: 7. Serial Connector 8. 14 pin Plug 9. 4 pin Power Connector 1 2 3 4 5 7 6 8 9
Beam 9602, www.beamcommunications.com 16 9602 SBD Modem | Installation and User Manual Specification Summary 9602 SBD MODEM Electrical Power 9 – 32 VDC, 1A Plug-pack (if provided) 100-240VAC 50/60Hz input Power Consumption Idle Average (measured over 5 min with one full message Tx/Rx every minute) 30mA (0.36W at 12V in) Transmit Mode Peak 125mA (1.5W at 12V in) Modem Type SBD Data only Speed 2400 bps EMC Compliance CE Environmental Operating Temperature Range -40°C to +85°C ambient Operating Humidity Range <75% RH Storage temperature -40°C to +85°C Weight 0.25 kg Dimensions 90 x 59 x 25mm RF Interface
www.beamcommunications.com 20 9602 SBD Modem | Installation and User Manual Modes of Operation The serial interface is always in one of three modes: command mode, SBD data mode or SBD session mode. When the data port is in command mode, AT commands can be entered to control the 9602 SBD MODEM. In command mode, ow control has no eect, with the RTS input ignored and the CTS output
Beam 9602, www.beamcommunications.com 9602 SBD Modem | Installation and User Manual 19 RS232 Port Electrical Parameters The LBT Data Port conforms to the RS232 interface specication with the following parameters: Parameter Specication Communication Rate 600 to 115,200 Baud Protocol 1 start bit, 8 data bits, no parity, 1 stop bit, asynchronous. Voltage Levels and Sensitivity RS232 compliant Auto-baud is not supported in 9602 SBD MODEM SBD Transceiver. The baud rate can be set via the AT+IPR command. The default rate is 19200 bps Data Connectivity To connect your 9602 SBD MODEM to a PC or laptop, simply connect either: 1. The
Beam 9602, GLOBAL HEAD OFFICE 8 Anzed Court Mulgrave, Victoria, Australia, 3170 Tel: +61 3 8588 4500 | Fax: +61 3 9560 9055 AMERICAS Tel: +1 954 524 2326 | Fax: +1 954 337 3778 EUROPE Tel: +44 208 144 1405 | Fax: +44 208 289 3542 Sales | [email protected] General | [email protected] Support | [email protected] www.be a m c o m m u nication s . c o m BEAM Resellers Part Number: USRMAN007501
www.beamcommunications.com 9602 SBD Modem | Installation and User Manual 23 Beam Warranty Conditions Beam Communications gives this express warranty (along with extended warranty endorsements, where applicable) in lieu of all other warranties, express or implied, including (without limitation), warranties of merchantability and tness for a particular purpose. This constitutes our so
Beam 9602, www.beamcommunications.com 14 9602 SBD Modem | Installation and User Manual Check in Device Manager that the new port has installed correctly. start -> Control Panel -> System -> Hardware -> Device Manager or start -> Run -> Type devmgmt.msc. Hit Enter If necessary, expand the Ports list by clicking the ‘+’ next to Ports (COM & LPT)
Beam 9602, www.beamcommunications.com 4 Content User / Installer Information 3 Equipment Overview 5 About BEAM Communications 6 Conventions in this Manual 7 Safety Information 7 What is the 9602 SBD Modem? 8 Package Contents 8 Optional BEAM Accessories 8 Installing the 9602 SBD Modem 9 Connecting the antenna cable 9 Connecting the power and IO cables and USB cable 10 How to Mount the 9602 SBD Modem 11 Installing the USB Drivers 12 Dimensions 15 Specication Summary 16 RS232 Specication 17 Physical Connection 17 RS232 Port signal support and handshaking 17 RS232 port electrical parameters 19 Data Connectivity 1
Beam 9602, 9602 SBD Modem | Installation and User Manual 7 Conventions in this Manual Warnings, cautions and notes appear throughout this manual. They are represented by following conventions. Warning: This symbol and associated text indicate a warning note providing information to prevent personal injury or damage to equipment. Note: This symbol and associated text indicate a note providing general operating information. Interference: All wireless phones may get interference, which could aect performance. Safety Information Note: Read the following information before installing and using the BEAM 9602 SBD Modem. Your 9602 SBD Mo
www.beamcommunications.com 10 Connecting the Power & IO Cables and USB Cable The supplied cable, CBLASY0146 provides connection to both the power input and the 9 way RS232 serial port. The module is powered from a 9 to 32V DC supply using a 4-pin square Molex connector from the Power & IO cable and attaching to the DC Power cable. Attach the Red and Black wires to a compliant powe
Beam 9602, www.beamcommunications.com 9602 SBD Modem | Installation and User Manual 21 RF Interface This section describes the physical connector and RF specications of the RF Interface. Antenna Connector The 9602 SBD MODEM will have the following antenna connector characteristics: Parameter Value Impedance - 50 Ohms nominal Gain - 3dBi Polarization - RHCP VSWR (maximum operational) - 1.5 : 1 Note: Existing qualied Iridium antennas may be used. (i.e. antennas designed for the 9522 and 9522A and 9601)
Beam 9602, www.beamcommunications.com 8 9602 SBD Modem | Installation and User Manual What is the 9602 SBD Modem? The 9602 SBD MODEM is a Remote Satellite Short Burst Data only modem designed to provide a reliable and cost eective means of Iridium SBD development. It utilizes the Iridium SBD (Short Burst Data) module and provides both D9 RS232 and USB Mini-B connectors, for direct connection to a PC. Key Features: • Small form Factor • No SIM Card Required • Maximum mobile originated message size of 340 bytes • Maximum mobile terminated m
www.beamcommunications.com 9602 SBD Modem | Installation and User Manual 3 User / Installer Information Please record your serial number here for future reference: Model: 9602 SBD MODEM Serial no.: This number can be copied from the white shipping label on the 9602 SBD MODEM box Eg. SB202833 Installation Location: Installation Dat
Beam 9602, www.beamcommunications.com 9602 SBD Modem | Installation and User Manual 13 Ensure that Search removable media (oppy, CD-ROM…) is selected then click Next. The sequence will then need to be repeated for USB Serial Port
Beam 9602, www.beamcommunications.com 9602 SBD Modem | Installation and User Manual 17 RS232 Specification The 9602 SBD MODEM is provided with an RS232 serial port for data connection. The 9-pin D-type (female) socket is wired DCE for connection to a standard PC with a 1:1 cable. Physical Connection The pin-out of the connector is described in the following table: Pin Signal Direction Description 1 DCD Modem PC Data Carrier Detect (Driven ON at all times) 2 RXD Modem PC Received Data 3 TXD PC Modem Transmitted Data 4 DTR PC Modem Date Terminal Ready 5 GND Signal
Beam 9602, 9602 SBD Modem | Installation and User Manual 11 How to Mount the 9602 SBD Modem The 9602 Modem is designed to be mounted using the two 4mm holes on the connector end of the enclosure. Self-tapping screws (eg. #6), or M3 or M4 machine screws/bolts can be used to mount the modem to a at surface. Please note mounting screws are not included. NOTE: • To ensure reliable sturdy xing: • Mount the 9602 Modem on a clean, even surface. • Use the correct type of screws. • If mounting on brick or poured concrete surface, let the cement completely dry before you mount the unit. • If mounting
Beam 9602, www.beamcommunications.com 9602 SBD Modem | Installation and User Manual 9 Installing the 9602 SBD MODEM Connecting the Antenna Cable 1. Screw the TNC-F to SMA-M coaxial adaptor onto the antenna jack located on the bottom end of the module. 2. Ensure that the cable being used is long enough to reach from the 9602 SBD MODEM to the Antenna location. Plug the antenna cable into the adapter. 3. Ensure that you fasten the antenna cable securely to the TNC jack by screwing the cable rmly all the way in with your ngers. 4. Please refer to the Antenna Installation Guide for important information on installation and placement of your antenna. Note:
Beam 9602, www.beamcommunications.com 2 9602 SBD Modem | Installation and User Manual 9602 SBD Modem Installation and User Manual GLOBAL HEAD OFFICE 8 Anzed Court Mulgrave, Victoria, Australia, 3170 Information furnished by Beam Communications Pty Ltd (Beam) is believed to be accurate and reliable. However, no responsibility is assumed by Beam for its use, or for any infringement of patents or other rights of third parties, which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Beam.
Beam 9602, www.beamcommunications.com 6 About BEAM Communications BEAM Communications, a wholly owned subsidiary of World Reach Limited (WRR), listed on the Australian Stock Exchange, is a world leader in design, manufacture and distribution of specialized communications equipment for the Iridium Satellite Network. BEAM’s commitment to be at the forefront has continued to increase its share of the global satellite communications market. Its premium distribution network spans the world. Recognized as a leading provider of satellite communication solutions, BEAM specializes in Voice, Data, Tracking and customized solutions. BEAM develops innovative products and service
NETGEAR WNDR3700v3 Modem Installationsanleitung
WNDR3700v3 |
SMC Networks SMC EZ Connect SMC70032AE Modem Operation & user’s manual
SMC EZ Connect SMC70032AE |
NETGEAR CBVG834G Modem Adminstrators user manual
CBVG834G |
Digi Modem Digi One IA Modem Quick start manual
Modem Digi One IA |
NETGEAR WNDR4000 - N750 WIRELESS DUAL BAND GIGABIT ROUTER Modem Specifications
WNDR4000 - N750 WIRELESS DUAL BAND GIGABIT ROUTER |
ZyXEL Communications NWA-3160 Modem Operation & user’s manual
NWA-3160 |
Toshiba A305 Modem Specifications
A305 |
Cisco BWX360 WiMAX Modem Operation & user’s manual
BWX360 WiMAX |
# | Manufacturer | Model | Document Type | File | Updated | Pages | Size |
---|---|---|---|---|---|---|---|
1 | Sony | CDX-636 | Product manual | sony/cdx-636-BJ7.pdf | 09 Jul 2022 | 2 | 0.2 Mb |
2 | General Technomatic | HWK-800 | Operation & user’s manual | general-technomatic/hwk-800-2YD.pdf | 22 Feb 2023 | 20 | 0.79 Mb |
3 | Samsung | Tray Design | Operation & user’s manual | samsung/tray-design-JV1.pdf | 14 Aug 2023 | 9 | |
4 | Topcom | 110 | Operation & user’s manual | topcom/110-633.pdf | 24 Feb 2024 | 3 | 0.13 Mb |
5 | Dehler | 34 | Owners & safety manual | dehler/34-1P5.pdf | 10 Mar 2024 | 94 | |
6 | LG | LFC25760 | Specifications | lg/lfc25760-8Q4.pdf | 23 Mar 2024 | 2 |
Tripp Lite
1Quick Start GuideUSB 2.0 Dual-Band Wi-Fi AdapterModel: U263-AC6001111 W. 35th Street, Chicago, IL 60609 USA tripplite.com/supportCopyright © 2021 Tripp Lite. All rights reserved.PROTECT YOUR INVESTMENT!Register your product for quicker service and ultimate peace of mind. You could also win an ISOBAR6ULTRA® surge protector—a $100 value!tripplite.com/war …
U263-AC600(36 pages) |
Racelogic
NTRIP Modem - Quick Start GuideThe Racelogic NTRIP Modem allows an RTK enabled VBOX to receive positional correction data via NetworkRTK without having to use a VBOX Base Station. Configuration is made via a Wi-Fi access point and the front screenwill display status and connection information.RegistrationSo that Racelogic can continue to provide you with not …
NTRIPMDM-V1(7 pages) |
Zhone
December 2000Firmware Compatibility NoticeDue to the discontinuation of a memory circuit, COMSPHEREr Models 3810Plus, 3811Plus, 3920,and 3921 have a new design. This new design contains hardware that will only operate correctly withcurrent and future versions of firmware. This affects models stamped with serial number 5106805and greater. If you download a pr …
3810Plus(1 pages) |
2Wire
Gateway to the Digital HomeBuilt to Suit Your Business Needs2Wire gateways are available in a variety of broadband interfaces, and offer exible wired and wireless networking options. While all of your customers will enjoy a high performance router, professional grade rewall, and simple browser based user interface, you can customize models with a va …
2071(4 pages) |
Radyne
DMD50 Universal Satellite Modem Installation and Operation Manual TM118 Revision 1.1 Radyne Corporation • 3138 E. Elwood St. • Phoenix, AZ 85034 • (602) 437-9620 • Fax: (602) 437-4811 • www.radn.com
…
DMD50(237 pages) |
Digisat
ModemsCDM-570/L & CDM-570/L-IP Satellite Modems Overview The CDM-570 and the CDM-570L are Comtech EF Data’s entry-level satellite modems that provide industry leading performance and flexibility in a 1 RU package at a very competitive price. Designed to address the market for low-cost terminals, the modems are available with 70/140 MHz or L-Band …
CDM-570/L(4 pages) |
Nakamichi Amplifier CA-5Nakamichi Product Manual: CA-5 PDF Service manual - 591S7G CA-5, 15 |
Whirlpool Water Dispenser WHCF-DWHWhirlpool Water Dispenser Installation, use & care manual (File: whirlpool-whcf-dwh-water-dispenser-4, Wed 11.2023) WHCF-DWH, 4 |
GRASS VALLEY Security Camera HD WIRELESS -Security Camera Operation & user’s manual (GRASS VALLEY HD WIRELESS -) HD WIRELESS -, 86 |
Brother Printer ImageCenter ADS-2400NPDF Manual (@W1Z7RG), Brother ImageCenter ADS-2400N Printer (15.01.2024) ImageCenter ADS-2400N, 16 |
Sven Keyboard comfort 3050#CQ8XCL comfort 3050: Sven Keyboard Owner Documentation comfort 3050, 10 |
IOTA Battery Charger DLS SERIESBattery Charger Product reference sheet (IOTA DLS SERIES) DLS SERIES, 2 |
BodyCraft Home Gym STRATABodyCraft STRATA User Guide (Instruction manual), @4A83SW STRATA, 22 |
Audio Note Amplifier M5 PhonoAmplifier Owner's information (Audio Note M5 Phono) M5 Phono, 15 |
Digitrax Toy Zephyr Express DCS52Toy Manual (Digitrax Zephyr Express DCS52) Zephyr Express DCS52, 44 |
BMS Transmitter NT5723SDHDTransmitter Operation manual (BMS NT5723SDHD) NT5723SDHD, 13 |
Zehnder Rittling Fan comfocoolUser Guide: Zehnder Rittling comfocool (9RNUIX, Upd.Mon 09.2023) comfocool, 32 |
SPM Water Dispenser SUPERCOLD 12 LT#917KSK: SUPERCOLD 12 LT Water Dispenser Instruction manual SUPERCOLD 12 LT, 63 |