Black Horse Model SU-26M Instruction Manual Book
|
Black Horse Model SU-26M, Instruction Manual book SPECIFICATION Made in Vietnam. Wingspan : 2,240mm. 88.19 in. Length : 1,950 mm. 76.77 in. Weight : 8.5kg. 18.7 lbs. Radio : 8 channels. Servo : 8 servos. (JR DS: 8321-FUTABA: BLS252). Glow Engine : OSGT 55- 62cc gas. ITEM CODE: BH96.
Black Horse Model SU-26M, 2 SU-26M - ITEM CODE: BH96. Instruction Manual This instruction manual is designed to help you build a great flying aeroplane. Please read this manual thoroughly before starting assembly of your SU-26M. Use the parts listing below to identify all parts. WARNING. Please be aware that this aeroplane is not a toy and if assembled or used incorrectly it is capable of causing injury to people or property. WHEN YOU FLY THIS AEROPLANE YOU ASSUME ALL RISK & RESPONSIBILITY. If you are inexperienced with basic R/C flight we strongly recommend you contact
Black Horse Model SU-26M, 3 SU-26M - ITEM CODE: BH96. Instruction Manual Caution: this model is not a toy! If you are a beginner to this type of powered model, please ask an experienced model flyer for help and support. If you attempt to operate the model without knowing what you are doing you could easily injure yourself or somebody else. Please keep your safety and well-being in mind at all times. Important: before you start construction Even if you have already built a large number of RC models please read right through these instruction
4 SU-26M - ITEM CODE: BH96. Instruction Manual REPLACEMENT SMALL PARTS 2. Wheels. 1. Aluminium landing gear. 7. Plastic part for tail gear. 3. Plastic parts for rudder pushrod. 6. Tail gear set. 4. Spinner. 5. Plastic part for fuselage. 2. Using a modeling knife, remove the cov- ering
Black Horse Model SU-26M, 5 SU-26M - ITEM CODE: BH96. Instruction Manual 4. Drill 1,5mm pilot holes through the block of wood for each of the four mounting screws provided with the servo. Install servo into ai- leron servo tray as same as picture below. 3. Using the thread as a guide and using masking tape, tape the servo lead to the end of the thread: carefully pull the thread out. When you have pulled the servo lead out, re- move the masking tape and the servo lead from the thread. 5. I
Black Horse Model SU-26M, 6 SU-26M - ITEM CODE: BH96. Instruction Manual Installing the aileron linkages as pictures below. Attach the clevis to the outer hole in the con- trol horn. INSTALLING THE AILERON LINKAGES 1. 3x15mm 96 mm Secure C/A glue INSTALLING THE AILERON SERVOS 2. 2 x 12 mm. INSTALLING THE AILERON CONTROL HORN 2. 3 x 35 mm. Secure aileron
Black Horse Model SU-26M, 7 SU-26M - ITEM CODE: BH96. Instruction Manual PARTS REQUIRED 1. Assemble and mounting the wheel pants as shown in the following pictures. MAIN GEAR INSTALATION. Installing the aileron linkages as pictures below. Secure C/A glue Secure Repeat the procedure for the other wing half. Elevator control horn 2. 3x15mm 96 mm INSTALLING THE AILERON LINKAGES 2. Bottom side. Secure Landing gear.
Black Horse Model SU-26M, 8 SU-26M - ITEM CODE: BH96. Instruction Manual Secure Bottom side Secure See pictures below: INSTALLING THE ENGINE MOUNT. Drill a hole 6mm diameter. INSTALLING THE STOPPER ASSEMBLY 1. The stopper has been pre-assembled at the factory. 2. Using a modeling knife, cut one length of silicon fuel line (the length of silicon fuel line is calculated by how the weighted clunk should rest about 8mm away from the rear of the tank
9 SU-26M - ITEM CODE: BH96. Instruction Manual 4. Carefully bend the third nylon tube down at a 45 degree angle (using a cigarette lighter). This tube will be vent tube to the fueling valve. When the stopper assembly is installed in the tank, the top of the vent tube should rest just below the top
Black Horse Model SU-26M, 10 SU-26M - ITEM CODE: BH96. Instruction Manual Do not secure the tank into place perma- nently until after balancing the airplane. You may need to remove the tank to mount the battery in the fuel tank compartment. INSTALLING THE ENGINE- THROTTLE. Remove covering. 4 x 40 mm. Fuel tank Silicon tube
Black Horse Model SU-26M, 11 SU-26M - ITEM CODE: BH96. Instruction Manual 1. Install one adjustable metal connector through the third hole out from the center of one servo arm, enlarge the hole in the servo arm using a 2mm drill bit to accommodate the servo connector. Remove the excess mate- rial from the arm. After installing the adjustable metal con- nector apply a small drop of thin C/A to the bottom nut. This will prevent the con- nector from loosening during flight. Secure Servo. Tie wrap. Right side. Right side. INSTALLING THE THROTTLE - CABLE
12 SU-26M - ITEM CODE: BH96. Instruction Manual COWLING. 1. Slide the fiberglass cowl over the en- gine and line up the back edge of the cowl with the marks you made on the fuselage. Top side Right side. 2. While keeping the back edge of the cowl flush with the marks, align the front of the c
13 SU-26M - ITEM CODE: BH96. Instruction Manual Install the spinner backplate, propeller and spinner cone. The spinner cone is held in place using two 3mm x 8mm machine screws. Trim and cut. 3 x 12mm Front view. Trim and cut. Secure INSTALLING THE SPINNER. Machine screw.
Black Horse Model SU-26M, 14 SU-26M - ITEM CODE: BH96. Instruction Manual 1. Install the rubber grommets and brass collets into the elevator servo. Test fit the servo into the servo tray. 2. Mount the servo to the tray using the mounting screws provided with your radio system. INSTALLING THE ELEVATOR SERVOS. HORIZONTAL STABILIZER. Horizontal stabilizer installation See picture below. Secure 165 mm 9
Black Horse Model SU-26M, 15 SU-26M - ITEM CODE: BH96. Instruction Manual 3 x 15mm Secure Elevator control horn install as same as the way of aileron control horn. Please see pic- tures below. Secure ELEVATOR CONTROL HORN INSTALLATION. 3 x 25 mm. Elevator control horn. Elevator pushrod install as same as the way of aileron pushrod. ELEVATOR PUSHROD INSTALLATION. 3 x 15 mm 134 mm Secure
Black Horse Model SU-26M, 16 SU-26M - ITEM CODE: BH96. Instruction Manual Rudder servo MOUNTING THE TAIL WHEEL BRACKET. Silicon tube 3x12mm 3x15mm Secure Elevator Pushrod Elevator Pushrod Secure Rudder servo install as same as method of elevator servo. See picture below: VERTICAL INSTALLATION. Rudder servo
18 SU-26M - ITEM CODE: BH96. Instruction Manual Rudder control horn install as same as the way of aileron control horn. Please see pic- tures below. Control horn of Rudder. 1. Rudder push - pull system install as same as picture below. RUDDER PUSHROD INSTALLATION. 3 x 40 mm Rudder control horn
Black Horse Model SU-26M, 19 SU-26M - ITEM CODE: BH96. Instruction Manual Rudder push-pull cable. 1. Plug the servo leads and the switch lead into the receiver. You may want to plug an aileron extension into the receiver to make plugging in the aileron servo lead easier when you are installing the wing . Plug the battery pack lead into the switch. 2. Wrap the receiver and battery pack in the protective foam to protect them from vi- bration. Use a rubber band or masking tape to hold the foam in place. Do not permanently secure the
Black Horse Model SU-26M, 20 SU-26M - ITEM CODE: BH96. Instruction Manual See picture wing attach to fuselage. Installing the fuselage hatch as same as pic- ture below. UBEC. Receiver *** Test fit the aluminium tube dihedral brace into each wing haft. The brace should slide in easily. If not, use 220 grit sand around the edges and ends of the brace until it fits prop- erly. Locate the aluminium wing dihedral brace. Silicon tube WING ATTACHMENT. 32 25 Right wing. 1,070 mm 880 mm 25 32 Wing bolt. Drill a hole 3mm diameter Right wing. Secure Top side 4 x 35mm Left wing. Wing bolt.
Black Horse Model SU-26M, 21 SU-26M - ITEM CODE: BH96. Instruction Manual Secure. Secure Drill a hole 3mm diameter Left wing. Plastic part bottom side fuselage Top side. Cut. Silicon tube
Black Horse Model SU-26M, 22 SU-26M - ITEM CODE: BH96. Instruction Manual Plastic parts of rudder pushrod. C/A glue Plastic part for tail gear. C/A glue Remove covering Cut. Mark point
Black Horse Model SU-26M, 23 SU-26M - ITEM CODE: BH96. Instruction Manual C/A glue 3. Turn the airplane upside down. Place your fingers on the masking tape and care- fully lift the plane . Accurately mark the balance point on the top of the wing on both sides of the fuselage. The balance point is located 138mm back from the leading edge. This is the balance point at which your model should balance for your first flights. Later, you may wish to experiment by shifting the balance up to 10mm forward or back to change the flying characteristics. Moving the balance forward may improve the smooth-
Black Horse Model SU-26M, 24 SU-26M - ITEM CODE: BH96. Instruction Manual 1. Completely charge your transmitter and receiver batteries before your first day of fly- ing. 2. Check every bolt and every glue joint in your plane to ensure that everything is tight and well bonded. 3. Double check the balance of the airplane. 4. Check the control surface. 5. Check the receiver antenna . It should be fully extended and not coiled up inside the fuselage. 6. Properly balan
Black Horse Model Liberty 182II Toy Instruction manual
Liberty 182II |
Black Horse Model Fieseler Fi156C STORCH Toy Instruction manual
Fieseler Fi156C STORCH |
Black Horse Model GLASAIR Toy Instruction manual book
GLASAIR |
Black Horse Model PITTS Toy Instruction manual book
PITTS |
Black Horse Model Ryan Toy Instruction manual book
Ryan |
Black Horse Model Edge 540-V3 Toy Instruction manual book
Edge 540-V3 |
Black Horse Model Extra 260-EP BH55 Toy Instruction manual book
Extra 260-EP BH55 |
Black Horse Model Mustang P51 Toy Instruction manual
Mustang P51 |
# | Manufacturer | Model | Document Type | File | Updated | Pages | Size |
---|---|---|---|---|---|---|---|
1 | Multi-code | 4140 | Installation instructions | multi-code/4140-4BY.pdf | 28 Nov 2023 | 2 | |
2 | InFocus | 410P | Operating instructions manual | infocus/410p-696.pdf | 05 Dec 2022 | 14 | |
3 | Lionel | New York Central Flyer | Owner's manual | lionel/new-york-central-flyer-W19.pdf | 07 Mar 2023 | 20 | |
4 | Fisher Research Labs | 1280-X Aquanaut | Operating manual | fisher-research-labs/1280-x-aquanaut-4N8.pdf | 03 Jan 2024 | 14 | |
5 | Alpine | CDA 9851 - Radio / CD | Owner's manual | alpine/cda-9851-radio-cd-UIT.pdf | 03 Oct 2022 | 36 | 0.98 Mb |
6 | Makita | 8419B | Instruction manual | makita/8419b-133.pdf | 11 Nov 2022 | 8 |
Viessmann
37400N Bahnhof Böblingen mit Etageninnenbeleuchtung, FunktionsbausatzN Station Böblingen with floor interior lighting Functional kitN87944Stand 02/sw01/2015SzT1Änderungen vorbehalten.Modifications reserved.Sous réserve de modifications.DEENEinsteigerBeginnersFortgeschritteneProfisProfessionalsAdvancedDébutantModéliste confirméProfessionnel37400N Bahnh …
Kibri 37400(6 pages) |
Kadee
INSTALLATION INSTRUCTIONS for the No. 811 DELAYED uncoupler -read complete instructions before starting.The No. 811 uncoupler is Delayed. It is to be used with Kadee O scalecouplers.Permanent magnetmounts between railsTO MOUNT:This uncoupler must be mounted exactly in the center of the track so firstfind the center between the rails and mark it. The uncouple …
O-SCALE 811(2 pages) |
Eduard
1/4Kübelwagen Typ 8228 50228 5021/48 scale detail set for Tamiya kit 32501 • sada detailù pro model 325011/48 TamiyaORIGINAL KIT PARTSPÙVODNÍ DÍLY STAVEBNICEPHOTO-ETCHED PARTSLEPTANÉ DÍLYPARTS TO BE REMOVEDDÍLY K ODSTRANÌNÍFILLTMELITeduardREMOVEODSTRANITOPTIONVOLBA?REPLACENAHRADITBENDOHNOUTGRINDOBROUSITSYMETRICAL ASSEMBLYSYMETRICKÁ MONTÁŽDRILL …
Kubelwagen Typ 82(4 pages) |
PLAYTIVE JUNIOR
1IAN 285626TOY FIRE ENGINE VÉHICULE DE POMPIERNotice d’utilisation FEUERWEHRWAGENGebrauchsanweisung BRANDWEERWAGENGebruiksaanwijzing TOY FIRE ENGINEInstructions for use BRANDBILBruksanvisning PALOAUTOKäyttöohje UGNIAGESIU AUTOMOBILISNaudojimo instrukcija
…
285626(20 pages) |
Laser Pegs
h45° PEGPlease read manual before you begin! Failure to follow this manual’s instructions may result in damage to the Triangle Power Base, AC adapter and/or Laser Pegs®. Not adhering to these directions will void the manufacturer’s warranty.Packing has to be kept since it contains important information.This manual is copyright and cannot be reproduced …
2230(4 pages) |
Talk To Me Technologies
Create a New, Blank Board 1. Tap on the profile icon in the upper right corner > Create a New Board.2. Use the dialogue that opens to specify a name, number of rows and columns, assign visibility and a representative icon for the board.3. Pre-populate the board with labels, if desired. 4. Press Create Board to finish and save, or Cancel to exit withou …
wego A(2 pages) |
DURKOPP ADLER Sewing Machine 567 CLASSICDURKOPP ADLER 567 CLASSIC User Manual (Doc Type: Sewing Machine Operating instructions manual) 567 CLASSIC, 76 |
Grizzly Saw g0555lanv insertSaw PDF Manual insert g0555lanv insert, 78 |
Frigidaire Air Conditioner FRA144HT2#M9EFN2 FRA144HT2: Frigidaire Air Conditioner Owner Documentation FRA144HT2, 3 |
Sony Security Camera SNC-RX550N - IPELA Network CameraSony Security Camera Manual (File: sony-snc-rx550n-ipela-network-camera-manual-8, 16th Sep 2023) SNC-RX550N - IPELA Network Camera, 8 |
Pogo MP3 Player PRY900M2User Manual: Pogo PRY900M2 (ZZKJO7, Upd.Sun 11.2023) PRY900M2, 42 |
Navitar Projector Accessories 671MCL012671MCL012 Installation instructions - 9L482Q 671MCL012, 1 |
Icom Two-Way Radio IC-F510#EPVT9C IC-F510: Icom Two-Way Radio Owner Documentation IC-F510, 24 |
Aroma Rice Cooker ARC-1030SBGuide: Aroma ARC-1030SB (8X692C, Upd.Wednesday 13-12-2023) ARC-1030SB, 34 |
Phil & Teds Motorized Toy Car voyagervoyager (Motorized Toy Car ePDF Manual, #6K57BO) voyager, 52 |
Kantech Receiver ioProx P700WLSKantech ioProx P700WLS Receiver Installation manual ioProx P700WLS, 13 |
Makita Vacuum Cleaner 447 MVacuum Cleaner Operating instructions manual (Makita 447 M) 447 M, 110 |
Middleby Marshall Oven TCO21140035Oven #DO24H2 TCO21140035, 12 |