BONANZA BEECHCRAFT Instruction Manual
|
SPECIFICATIONS Wingspan:.........................1580mm (62.2in) Length:.............................1190mm (46.8 in) Electric Motor:.....................See next pager Glow Engine:.................... .46 2-T / .70 4-T RTF Weight: 3.2Kg / 7.05lbs (Will vary with Equipment Used). Radio:......................6 Channel / 7-8 Servos Function: Ailerons-Elevator-Rudder-Throttle Flaps-Opt
BONANZA BEECHCRAFT, 1.5mm A B ! CA L/R Assemble left and right sides the same way. X Drill holes using the stated size of drill (in this case 1.5 mm ÿ) Use epoxy glue Take particular care here Hatched-in areas: remove covering film carefully Not included. These parts must be purchased separately Check during assembly that these parts move freely, without binding Apply cyano glue SILICON EPOXY A EPOXY B CA GLUE Epoxy Glue ( 5 minute type) Silicon sealer Cyanoacrylate Glue Minimum 6 channel radio for airplane with 5 (4 for EP) standard servos and two servo mini
BONANZA BEECHCRAFT, 1-Cut away the covering of the wing bottom where the aileron servo goes. 2-Connect the aileron servo cord to the aileron extension cord. 3-Install the aileron servo on the servo mount. -Switch on the radio (trims centered) then mount the ailerons servo horn in neutral position. -The servo horn should be perpendicular to the servo YES NO 1-Depending on the position of the linkage, determine the location of aileron control horn. The horn holes must be perfectly aligned with the axis of articulation. 2-Mark the positi
RECEIVER ELECTRIC RETRACT LANDING GEAR ON OFF GEAR EXTENDED POSITION RETRACTED POSITION 2mm 2mm 1.5mm gear cover Gear mount gear strap 1/16 1/8x13/32”(3x10mm) 5/64x15/64”(2x6mm) ..........8 ..........8 5/32”(4mm) collar ..........2 ........2 ..........2 CA Thin CA CA Thin CA 6x23mm wooden dowel 4-Electric retract 6-Fixed gear installation WING - BOTTOM VIEW Electric retract must be
BONANZA BEECHCRAFT, Cut away only the covering both the right and left side Trial fit the horizontal stabilizer in place . Check the alignment of the horizontal stabilizer. When you are satisfied with the alignment, use a pencil to trace around the top and bottom of the stabilizer where it meets the fuselage. 7-Horizontal Stabilizer Remove the horizontal stabilizer from the vertical stabilizer. Using a straight edge and a sharp hobby knife, carefully cut away the covering inside the lines which were marked above. Be cautious not to cut into the wood-this will weaken the structure. Again, slide the horizontal stabilizer into the slot on the fuselage. Check the alignment of the horizontal st
BONANZA BEECHCRAFT, CA Thin CA Trial fit the vertical stabilizer in place . Check the alignment of the vertical stabilizer. When you are satisfied with the alignment, use a pencil to trace around the left and right of the vertical stabilizer where it meets the fuselage. With the perpendicular, check the alignment of the vertical stabilizer and the horizontal stabilizer. When you are satisfied with the alignment, secure the vertical stabilizer in place using thin CA glue. Remove the vertical stabilizer from the fuselage. Using a sharp hobby knife, carefully cu
BONANZA BEECHCRAFT, Plastic control horn .....................1 CA Apply thin CA glue on the top of the hinge Apply a thin layer of petroleum jelly VERTIAL STABILIZER VERTICAL STABILIZER TOP-VIEW ! Securely glue together. If coming off during fly, you lose control of your air plane. Cut away only the covering Note: the rectangular hole for the control horn installation is pre-cut at factory. CA Thin CA ! Securely glue together. If coming off during fly, you lose control of your air plane. CA Thin CA CA Thin CA Repeat the previous procedures to hinge the second elevator to the other side of the horizontal stabilizer. 9- Rudder
BONANZA BEECHCRAFT, 2- Insert “Z” bend of steering linkage inside the hole of front landing gear Steering arm. 3- Position the steering arm inside the front landing gear mount already Attached to the firewall. 5- Screw steering arm on the leg. Nose gear mount 3x20mm screw...4 Steering arm...1 ..............1 IN CASE OF ELECTRIC RETRACT LANDING GEAR USING Nose gear pushrod Steering horn 10-Nose gear (Electric retract landing gear and Struts must purchase separately) 1 2 3 3mm nut, washer...4 1- Route the steering linkage into the fuselage and through the fire-wall. 4- S
BONANZA BEECHCRAFT, A 5mm 13/64” Remove the engine mount and drill a 13/64”(5mm) hole through the fire-wall at each of the four marks marked. Using a pencil or felt tipped pen, mark the fire wall where the four holes are to be drilled. Reposition the engine mounts on to the fire-wall. Attach the four blind-nut to the fire-wall as show. Secure them with four 4x25mm screw. Position the engine on to the engine mounts so the distance from the prop hub to the fire- wall from124 to 130mm. Mark the engine mounting plate where the four holes are to be drilled. ! Engine thrust on balk head is already adjust at factory. Remove the engine and drill a 1/8”(3mm) holes through the beam at eac
BONANZA BEECHCRAFT, Firewall C’ C C=C’ ! Engine thrust on balk head is already adjust at factory Using a aluminum motor mounting plate as a template, mark the plywood motor mounting plate where the four holes are to be drilled . 6mm SIDE-VIEW 1-Attach the board or transparent plastic on the side of the fuselage with the adhesive tape as show. 2-Using a pencil or felt tipped pen trace around the engine head where it meet the cowl. Cut the opening the board or transparent plastic for the engine head as marked before. 3-Remove the engine and insert the cowl on to the fuselage so the distance from the fire wall to the front of the cowl from124 to 130mm. Trace around inside the hole
BONANZA BEECHCRAFT, FUEL TANK OR LI-PO BATTERY AREA Shift the location of the fuel tank, battery pack, or Li-po battery as needed to obtain the specified CG. Rudder servo Elevator servo Throttle servo FUSELAGE - TOP VIEW FUSELAGE - TOP VIEW 16-Linkages Elevator push rod Elevator push rod Rudder push rod ................1 ....................3 2mm Connector X 3mm set Screw 2 mm Elevator pushrod Elevator pushrod FUSELAGE - TOP VIEW FUEL TANK OR LI-PO BATTERY AREA Rudder servo Elevator servo Throttle servo Rudder push-rod Elevator push-rod Nose gear push-rod Throttle push-rod 15- Servo
BONANZA BEECHCRAFT, 20- Decor Note: Glue the Right and Left gear door on to the fuselage only. Do not glue them to the cowl if you want to remove the cowl out of the fuselage. Nose Gear door installation Gear door (3mm plywood) Do not glue here. CA WING 5x25mm screw 5X25mm screw ......2 ......2 19- Installation the wing Secure the wing in place using the 5x25mm screw. CA Sticker Sticker Sticker Sticker Note: Cut out the stickers and apply them in the proper area. Do not peel the backing paper off all at once. Peel off
Wing center section DO NOT try to fly an out-of-balance model ! 128mm (5”) Note: If necessary, move the battery pack or add weight to either the tail or nose until the correct balance is achieved. RUDDER / SEITENRUDER ELEVATOR / HOHENRUDER Take off /Start 10mm (25/64”) Landing /Landung 22mm (55/64”) AILERON / QUERRUDER FLAP / LANDEKLAPPEN 32mm (1.25�
FMS 70 MM A-10 THUNDERBOLT II Toy Operating manual
70 MM A-10 THUNDERBOLT II |
VTech Explore My School Toy Operation & user’s manual
Explore My School |
marklin 20672 Toy Startup manual
20672 |
Edge BH92-A Toy Instruction manual book
BH92-A |
Air Hogs 360 Hoverblade Toy Manual
360 Hoverblade |
LEGO 60147 Toy Assembly instructions manual
60147 |
marklin 36744 Toy Instruction manual
36744 |
Fisher-Price DOODLE PRO M1353 Toy Operation & user’s manual
DOODLE PRO M1353 |
# | Manufacturer | Model | Document Type | File | Updated | Pages | Size |
---|---|---|---|---|---|---|---|
1 | Soundstream | D60 | Owner's manual | soundstream/d60-1F8.pdf | 20 Jan 2024 | 4 | 0.13 Mb |
2 | Epson | LQ-590 | Specifications | epson/lq-590-24C.pdf | 19 Nov 2023 | 2 | 0.31 Mb |
3 | Basler | BIP2-DXXXXc-dn | Operation & user’s manual | basler/bip2-dxxxxc-dn-54F.pdf | 30 Mar 2023 | 114 | |
4 | Hussmann | IMPACT RLNI | Technical data sheet | hussmann/impact-rlni-EEQ.pdf | 01 Sep 2022 | 6 | |
5 | LG | L1922P | Operation & user’s manual | lg/l1922p-YM2.pdf | 07 Nov 2023 | 23 | |
6 | EINHELL | DSE 125 | Original operating instructions | einhell/dse-125-6DL.pdf | 09 Nov 2023 | 48 |
Fei Bao
DISCLAIMER:THIS IS NOT A TOY. This is a high-performance miniature aircraft, capable of high speeds and damage to life, limb, and property. The manufacturer and its distributors cannot control how you assemble this model, what equipment you use to fit it out, or how you fly it, and can assume no liability whatsoever for any damages that may occur when you …
T45(23 pages) |
Maya Group
INSTRUCTION GUIDEDO NOT EAT ORBEEZ.Safety and Disposal Instructions• Orbeez beads contains copolymer of sodium acrylic acid (Acrylic acid, sodium hydroxide and water) and color pigmentation.• Dispose of Orbeez® in trash or work into garden soil. Because Orbeez give off water when it is dry, they can be used to hydrate soil and conserve water usage. • …
Orbeez Crush CRUSHKINS PETS(2 pages) |
RadioLink
RadioLink Electronic Ltdwww.radiolink.comA5603D Fixed Wing Vertical Flight with 1 SwitchInstruction ManualCE FCC RoHS* Note: There are 2 versions of A560, including RTF version and PNP version.Please refer to page 3-22 of this manual for RTF version, and page 23-27 for PNP version.
…
A560(28 pages) |
Eduard
STURMTIGER exterior35 9591/35 scale detail set for kit • sada detailů pro model 1/35REVELL REVELLORIGINAL KIT PARTSPŮVODNÍ DÍLY STAVEBNICEPHOTO-ETCHED PARTSLEPTANÉ DÍLYPARTS TO BE REMOVEDDÍLY K ODSTRANĚNÍFILLTMELITeduardREMOVEODSTRANITOPTIONVOLBA?REPLACENAHRADITBENDOHNOUTGRINDOBROUSITSYMETRICAL ASSEMBLYSYMETRICKÁ MONTÁŽDRILL HOLEVRTAT OTVORAPPL …
STURMTIGER exterior(4 pages) |
Italeri
2cmFlakvierling 38I numeri si riferiscono all’assortimento colori ITALERI /Acryl Paint SystemThe indicated colour number refer to the ITALERI /Acryl Paint SystemDie angegebenen farbnummern beziehen sich auf die ITALERI /Acryl Paint SystemLes références indiquées concern …
7026(6 pages) |
Black Horse Model
SPECIFICATION Wingspan : 1,000 mm 39.37 in. Length : 860 mm 33.86 in. Weight : 1,4 kg 3.08 Lbs. Radio : 04 channels. Servo : 04 mini servos. Motor : KMS 282 …
MIDGET MUSTANG-EP(23 pages) |
LinMot DC Drives C1250-PD-XC-0SLinMot Product Guide: C1250-PD-XC-0S PDF Operation & user’s manual - 1AV9Z5 C1250-PD-XC-0S, 38 |
Toshiba Projection TV 46H8446H84 Owner's manual - 1QLA88 46H84, 63 |
Felt Bicycle FR SERIESBicycle #MFBV9K FR SERIES, 7 |
Tektronix Laboratory Equipment P7708Tektronix Laboratory Equipment Operation & user’s manual (File: tektronix-p7708-operation-user-s-manual-98, 06.09.2023) P7708, 98 |
Dell Server PowerVault NX3500#4DZJ6U PowerVault NX3500: Dell Server Owner Documentation PowerVault NX3500, 208 |
Sears Water Heater 153#2Z9HAV: 153 Water Heater Owner's manual 153, 32 |
LA Fitness Treadmill Runfit 99#9K1E16: Runfit 99 Treadmill Owner's manual Runfit 99, 41 |
ACME Speakers SS-204SS-204 (Speakers ePDF User Guide, #8M76NT) SS-204, 52 |
BENDIX Dishwasher BDW 45BENDIX Dishwasher BDW 45 Instruction booklet BDW 45, 16 |
BT Dehumidifier BT-ED-1622RBT-ED-1622R (Dehumidifier ePDF Manual, #8TUMD5) BT-ED-1622R, 2 |
Mission Speakers 700700 User instruction manual - 25WMK3 700, 8 |
Strategic Vista Security Camera CVC2632Installation instructions for Strategic Vista CVC2632 Security Camera CVC2632, 2 |