Manualios.com

Cisco 2960 8TC - Catalyst Switch Getting Started Manual

  • 2960 8TC - Catalyst Switch Switch
  • maHn1Hf8kVWEA
  • Getting Started Manual
  • PDF / Adobe Acrobat Reader
  • 22

Cisco 2960 8TC - Catalyst Switch Manual Online:

3.95, 1252 votes
Cisco 2960 8TC - Catalyst Switch User Manual
Cisco 2960 8TC - Catalyst Switch User Guide
Cisco 2960 8TC - Catalyst Switch Online Manual

Text of Cisco 2960 8TC - Catalyst Switch User Guide:

  • Cisco 2960 8TC - Catalyst Switch, Americas Headquarters Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 USA www.cisco.com Tel: 408 526-4000 800 553-NETS (6387) Fax: 408 527-0883 Asia Pacific Headquarters Cisco Systems, Inc. 168 Robinson Road #28-01 Capital Tower Singapore 068912 www.cisco.com Tel: +65 6317 7777 Fax: +65 6317 7799 Europe Headquarters Cisco Systems International BV Haarlerbergpark Haarlerbergweg 13-19 1101 CH Amsterdam The Netherlands www-europe.cisco.com Tel: 31 0 800 020 0791 Fax: 31 0 20 357 1100 Cisco has more than 200 offices worldwide. Addresses, phone numbers, and fax numbers are list

  • Cisco 2960 8TC - Catalyst Switch, 21 Duration of Hardware Warranty A Cisco product hardware warranty is supported for as long as the original end user continues to own or use the product, provided that the fan and power supply warranty is limited to five (5) years. In the event of a discontinuance of product manufacture, the Cisco warranty support is limited to five (5) years from the announcement of the discontinuance. Replacement, Repair, or Refund Policy for Hardware Cisco or its service center will use commercially reasonable

  • Cisco 2960 8TC - Catalyst Switch, 14 6 Connecting to the Switch Ports This section describes how to connect to the switch ports, the SFP module ports, and to the dual-purpose ports. For additional cabling information, see the Catalyst 2960 Switch Hardware Installation Guide on Cisco.com. Connect to the 10/100 and 10/100/1000 Ports Follow these steps: For simplified cabling, the automatic medium-dependent interface crossover (auto-MDIX) feature is enabled by default on the switch. With auto-MDIX enabled, the switch detects the required cable type for copper Ethernet connections and configures the interfaces a

  • 9 The Cisco Configuration Engine is a network management device that works with embedded CNS agents in the switch software. You can use Cisco Configuration Engine to automate initial configurations and configuration updates on the switch. See the “Accessing Help Online” section on page 18 for a list of supporting documentation. 5 Installing the Switch This section describes

  • 13 Mount the Switch with a Magnet Panel Follow these steps: 1. Position the mounting magnet on the mounting surface (see Figure 3). 2. Place the bottom of the switch on the mounting magnet (see Figure 3). Figure 3 Mounting the Switch with a Magnet Panel 1 C a ta ly s t 2 9 6 0 S e rie s STA T DPLX SPD SYST 1 x2 x 3 x 4 x 5 x 6 x 7 x 8 x C O N S O L E 2 1 3 210097

  • Cisco 2960 8TC - Catalyst Switch, 17 Troubleshooting Express Setup If Express Setup does not run, or if the Express Setup page does not appear in your browser: • Did you verify that POST successfully ran before starting Express Setup? • If not, make sure that only the SYST and STAT LEDs are green before pressing the Mode button to enter the Express Setup mode. • Did you press the Mode button while the switch was still running POST? • If yes, wait until POST completes. Power cycle the switch. Wait until POST completes. Confirm that the SYST and STAT LEDs are green. Press the Mode button to enter Express Setup mode. • Did you try to continue without confirming that the

  • Cisco 2960 8TC - Catalyst Switch, 11 Installation Warning Statements This section includes the basic installation warning statements. Translations of these warning statements appear in the Regulatory Compliance and Safety Information for the Catalyst 2960 Switch document that shipped with the switch. Warning To prevent the switch from overheating, do not operate it in an area that exceeds the maximum recommended ambient temperature of 113°F (45°C). To prevent airflow restriction, allow at least 3 inches (7.6 cm) of clearance around the ventilation openings. Statement 17B Warning This equipment

  • Cisco 2960 8TC - Catalyst Switch, 6 Step 10 Enter this information in the Network Settings fields: • In the Management Interface (VLAN ID) field, the default is 1. Enter a new VLAN ID only if you want to change the management interface through which you manage the switch. The VLAN ID range is 1 to 1001. • In the IP Address field, enter the IP address of the switch. The IP address is also assigned to the management VLAN. In the IP Subnet Mask field, click the drop-down arrow, and select an IP Subnet Mask. • In the Default Gateway field, enter the IP address for the default gateway (router). • Enter your pas

  • Cisco 2960 8TC - Catalyst Switch, GETTING STARTED GUIDE Catalyst 2960 Switch Getting Started Guide (8-Port Switches) INCLUDING LICENSE AND WARRANTY 1 About This Guide 2 Taking Out What You Need 3 Running Express Setup 4 Managing the Switch 5 Installing the Switch 6 Connecting to the Switch Ports 7 In Case of Difficulty 8 Obtaining Documentation and Submitting a Service Request 9 Cisco Limited Lifetime Hardware Terms

  • 12 Figure 1 Positioning the Template and Inserting the Screws 4. Place the switch onto the mounting screws, and slide it forward until it locks in place (see Figure 2). Figure 2 Placing the Switch on the Mounting Screws 1 3 2 210096 2x 3x 4x 5x 6x 7x 8x 1 Catalyst 2960 S eries CONSOLE 1x S P D D P L X S T A T S Y S T M O D E 210094

  • Cisco 2960 8TC - Catalyst Switch, 16 Connect to the Dual-Purpose Ports Follow these steps: Verify Port Connectivity After you connect to the switch port and another device, the port LED turns amber while the switch establishes a link. This process takes about 30 seconds, and then the LED turns green when the switch and the target device have an established link. If the LED is off, the target device might not be turned on, there might be a cable problem, or there might be a problem with the adapter installed in the target device. See the “In Case of Difficulty” section on page 16 for information about online assistance. 7 In Case of Difficulty If you experience difficulty,

  • Cisco 2960 8TC - Catalyst Switch, 4 3 Running Express Setup When you first set up the switch, you should use Express Setup to enter the initial IP information. This enables the switch to connect to local routers and the Internet. You can then access the switch through the IP address for further configuration. To run Express Setup: Step 1 Make sure that nothing is connected to the switch. During Express Setup, the switch acts as a DHCP server. If your PC has a static IP address, change your PC settings before you begin to temporarily use DHCP. Step 2 Power the switch as follows: • Catalyst 2960-8TC and 2960G-8TC switches: Connect the AC power cord to the switch power connector and to a grounded AC o

  • Cisco 2960 8TC - Catalyst Switch, 2 1 About This Guide This document describes information specific to the Catalyst 2960-8TC, Catalyst 2960G-8TC, and Catalyst 2960PD-8TT-L switches. For information applicable to the other Catalyst 2960 switches, see the Catalyst 2960 Switch Hardware Installation Guide on Cisco.com. This guide provides instructions on how to use Express Setup to configure your Catalyst switch. Also covered are switch management options, basic installation procedures, port and module connections, power connection procedures, and troubleshooting help. For additional installation and configuration information for Catalyst 2960 switches, see the Catalyst 2960 documentation on Cisco.com. For system req

  • Cisco 2960 8TC - Catalyst Switch, 15 Install the SFP Modules and Connect to the Ports Follow these steps: For a list of supported modules, see the release notes on Cisco.com. For detailed instructions on installing, removing, and connecting to SFP modules, see the documentation that came with the SFP module. Caution Removing and installing an SFP module can shorten its useful life. Do not remove and insert SFP modules more often than is absolutely necessary. Step 1 Grasp the module on the sides, and insert it into the switch slot until you feel

  • Cisco 2960 8TC - Catalyst Switch, 3 Shipping Box Contents 1 Catalyst 2960 switch 5 Four rubber mounting feet 2 Mounting magnet 6 Documentation 3 Screw template 7 AC power cord (AC-powered switches only) 4 Three number-8 Phillips pan-head screws 8 Console cable R egulatory C om pliance and S afety Infor m ation for the C a talyst 2960 S w itch D o cum en tation CD 1 2 3 4 5 6 7 8 202600 Catalyst 2960 S eries CONSOLE 1x SP D D P LX ST A T S YS T M O D E 2x 3x 4x 5x 6x 7x 8x 1

  • Cisco 2960 8TC - Catalyst Switch, 10 Before You Begin When you determine where to install the switch, verify that these guidelines are met: • Airflow around the switch and through the vents is unrestricted. Note We strongly recommend that you allow at least 3 inches (7.6 cm) of clearance around the ventilation openings. • Temperature around the switch does not exceed 113°F (45°C). • Humidity around the switch does not exceed 85 percent. • Altitude at the installation site is not greater than 10,000 feet (3,049 meters). • Do not place any items on the

  • Cisco 2960 8TC - Catalyst Switch, 19 For More Information For more information about the switch, see these documents on Cisco.com: • Release Notes for the Catalyst 3750, 3560, 2970, and 2960 Switches. Before you install, configure, or upgrade the switch, refer to the release notes on Cisco.com for the latest information. • Catalyst 2960 Switch Hardware Installation Guide. This guide provides complete hardware descriptions and detailed installation procedures. • Regulatory Compliance and Safety Information for the Catalyst 2960 Switch (ships with your product). This guide contains agency approvals, compliance information, and translated warning statements. • C

  • Cisco 2960 8TC - Catalyst Switch, 7 Refreshing the PC IP Address After you complete Express Setup, you should refresh the PC IP address. For a dynamically assigned IP address, disconnect the PC from the switch, and reconnect it to the network. The network DHCP server assigns a new IP address to the PC. For a statically assigned IP address, change it to the previously configured IP address. 4 Managing the Switch After completing Express Setup and installing the switch in your network, use the device manager, Cisco Network Assistant, or anothe

  • Cisco 2960 8TC - Catalyst Switch, 20 9 Cisco Limited Lifetime Hardware Terms There are special terms applicable to your hardware warranty and various services that you can use during the warranty period. Your formal Warranty Statement, including the warranties and license agreements applicable to Cisco software, is available on Cisco.com. Follow these steps to access and download the Cisco Information Packet and your warranty and license agreements from Cisco.com. 1. Launch your browser, and go to this URL: http://www.cisco.com/univercd/cc/td/doc/es_inpck/cetrans.htm The Warranties and License Agreements page appears. 2. To r ea d the Cisco Information Packet, follow these steps: a. Click the Informat

  • Cisco 2960 8TC - Catalyst Switch, 5 Step 7 Connect a Category 5 Ethernet cable to any 10/100 or 10/100/1000 Ethernet port on the switch front panel. Connect the other end of the cable to the Ethernet port on your PC. Step 8 Verify that the LEDs on both Ethernet ports are green. Wait 30 seconds. Step 9 Start a web browser on your PC. Enter the IP address 10.0.0.1 in the web browser, and press Enter. The Express Setup page appears. If it does not appear, see the “In Case of Difficulty” section on page 16 for help. Your entries should be in English. DHCP-enabled PC 210109 2x 3x 4x 5x 6x 7x 8x 1 Catalyst 2960 S eries CO NS OLE 1x S P D D P L X S T A T S Y S T M O D E

Related Products and Documents (Switch):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 Ritron JOBCOM JMX D Series Owner's manual ritron/jobcom-jmx-d-series-JBL.pdf 21 Oct 2022 20 1.36 Mb
2 NEC LCD1915X Operation & user’s manual nec/lcd1915x-22T.pdf 22 Feb 2023 44
3 Emerson HK39 Owner's manual emerson/hk39-K95.pdf 28 Dec 2022 6 0.99 Mb
4 Sound Storm SSV10.4FL Operation & user’s manual sound-storm/ssv10-4fl-6HQ.pdf 25 Aug 2023 12 0.74 Mb
5 Grizzly G9933 Parts list grizzly/g9933-C3F.pdf 22 Jun 2022 6 0.4 Mb
6 True Fitness Dipping Cabinet TDC-47 Specifications true-fitness/dipping-cabinet-tdc-47-2-8BC.pdf 25 Feb 2024 2 0.15 Mb

Similar Resources:

  • Dell

    PowerEdge M1000e

    (71 pages)
    PowerEdge M1000e Technical Guide Built from the ground up to combat data center sprawl and IT complexity, the PowerEdge M1000e enclosure delivers one of the most energy-efficient, flexible and manageable blade server products on the market. …
  • Siemens

    SIMATIC NET

    (50 pages)
    Extender for SCALANCE XM-400 ___________________ ___________________ ___________________ ___________________ ___________________ ___________________ ___________________ ___________________ SIMATIC NET Network components Extender for SCALANCE XM-400 Operating Instructions 05/2014 C79000-G8976-C332-03 Introduction 1 Safety notices 2 Description of the …
  • AKO Electronica

    AKO-5335

    (2 pages)
    UTILIZACIÓNEl interruptor de nivel AKO-5335, se utiliza en laseñalización, control y regulación de nivel, de productosen forma de grano o polvo, con un diámetro máximo de15 mm que fluyan por un silo, tolva o conducto.El aparato detecta particularmente la presencia o laausencia de producto a su nivel.La composición del AKO-5335, consiste en un moto-red …
  • Huawei

    Quidway S9300

    (80 pages)
    Quidway S9300 Terabit Routing SwitchV100R001C03Configuration Guide - IP ServiceIssue 02Date 2009-08-06Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd. …
  • Avaya

    8600

    (53 pages)
    Ethernet Routing Switch 8600/8800 Engineering > OSPF Technical Configuration Guide Avaya Data Solutions Document Date: November 2010 Document Number: NN48500-602 Document Version: 1.4 …
  • Brainboxes

    ES Series

    (53 pages)
    Brainboxes Limited, 18 Hurricane Drive, Liverpool International Business Park, Speke, Liverpool, Merseyside, L24 8RL Tel: +44 (0)151 220 2500 Fax: +44 (0)151 252 0446 Web: www.Brainboxes.com Email: [email protected] Brainboxes Industrial Ethernet to Serial Product Manual …

Comments, Questions and Opinions: