Manualios.com

Cisco Catalyst 2350 Installation Manual

Cisco Catalyst 2350 Manual Online:

4.7, 1843 votes
Cisco Catalyst 2350 User Manual
Cisco Catalyst 2350 User Guide
Cisco Catalyst 2350 Online Manual

Text of Cisco Catalyst 2350 User Guide:

  • Cisco Catalyst 2350, 4-4 Catalyst 2350 Switch Hardware Installation Guide OL18479-01 Chapter 4 Troubleshooting Clearing the Switch IP Address and Configuration To maximize switch performance and to ensure a link, follow one of these guidelines when changing the duplex or speed settings. • Let both ports autonegotiate both speed and duplex. • Manually set the speed and duplex parameters for the ports on both ends of the connection. • If a remote device does not autonegotiate, set the same duplex settings on the two ports. The speed parameter adjusts itself even if the connected port does not autonegotiate. Autonegotiation and Network Interface Cards Problems sometimes occur bet

  • Cisco Catalyst 2350, 1-4 Catalyst 2350 Switch Hardware Installation Guide OL18479-01 Chapter 1 Overview Front Panel Description System LED The System LED shows whether the system is receiving power and is functioning properly. For information on the System LED colors during power-on self-test (POST), see the “Diagnosing Problems” section on page 4-1. Port LEDs and Modes Each Ethernet port and 10-Gigabit Ethernet module slot has a port LED. These port LEDs, as a group or individually, display information about the switch and about the individual ports. The port mode determines the type of inform

  • Cisco Catalyst 2350, 3-6 Catalyst 2350 Switch Hardware Installation Guide OL18479-01 Chapter 3 Power Supply and Fan Module Installation Installing a DC-Power Supply Step 6 Using a ratcheting torque screwdriver, torque the ground-lug screws to 60 lbf-in (960 ozf-in) ( Figure 3-5). Step 7 Connect the other end of the grounding wire to an appropriate grounding point at your site or to the rack. Figure 3-5 Attaching the Ground Lug and Wire Assembly on Catalyst 2350 Switches Installing the DC Power Supply in the Switch Step 1 T

  • Cisco Catalyst 2350, CHAPTER 1-1 Catalyst 2350 Switch Hardware Installation Guide OL18479-01 1 Overview The Catalyst 2350 switch, also referred to as the switch, is an Ethernet switch to which you can connect devices such as servers, routers, and other switches. • Switch Models, page 1-1 • Front Panel Description, page 1-1 • Rear Panel Description, page 1-5 • Management Options, page 1-8 Switch Models Note All switch models support the Cisco TwinGig Converter Module. Front Panel Description The switch front panel includes the 10/100/1000 Ethernet ports, the 10-Gigabit Ethernet module slots, and the switch LEDs. Figure 1-1 shows the Catalyst 23

  • Cisco Catalyst 2350, Contents v Catalyst 2350 Switch Hardware Installation Guide OL18479-01 Ping End Device 4-3 Spanning Tree Loops 4-3 Switch Performance 4-3 Speed, Duplex, and Autonegotiation 4-3 Autonegotiation and Network Interface Cards 4-4 Cabling Distance 4-4 Clearing the Switch IP Address and Configuration 4-4 Finding the Switch Serial Number 4-5 APPENDIX A Technical Specifications A-1 APPENDIX B Connector and Cable Specifications B-1 Connector Specifications B-1 10/100/1000 Ports B-1 10-Gigabit Ethernet Module Interfaces B-2 SFP Modules B-2 10/100 Ethernet Managemen

  • Cisco Catalyst 2350, 3-2 Catalyst 2350 Switch Hardware Installation Guide OL18479-01 Chapter 3 Power Supply and Fan Module Installation Installation Overview Warning Do not reach into a vacant slot or chassis while you install or remove a module or a fan. Exposed circuitry could constitute an energy hazard. Statement 206 Warning Only trained and qualified personnel should be allowed to install, replace, or service this equipment. Statement 1030 Warning Do not work on the system or connect or disconnect cables during periods of lightning activity. Statement 1001

  • Cisco Catalyst 2350, C-3 Catalyst 2350 Switch Hardware Installation Guide OL18479-01 Appendix C Configuring the Switch with the CLI-Based Setup Program Entering the Initial Configuration Information Completing the Setup Program The initial setup dialog appears at the console when you first press Enter. Step 1 Enter Yes at the following two prompts. Would you like to enter the initial configuration dialog? [yes/no]: yes At any point you may enter a question mark '?' for help. Use ctrl-c to abort configuration dialog at any prompt. Default settings are in square brackets '[]'. Basic mana

  • viii Catalyst 2350 Switch Hardware Installation Guide OL18479-01 Preface Warning This warning symbol means danger. You are in a situation that could cause bodily injury. Before you work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard practices for preventing accidents. Use the statement number provided at the end of

  • 2-12 Catalyst 2350 Switch Hardware Installation Guide OL18479-01 Chapter 2 Switch Installation Installing Devices in 10-Gigabit Ethernet Slots Installing Devices in 10-Gigabit Ethernet Slots These sections describe how to install and remove X2 transceiver converter modules. Use only Cisco X2 transceiver modules, converter modules, and SFP modules with the switch. Each C

  • Cisco Catalyst 2350, C-4 Catalyst 2350 Switch Hardware Installation Guide OL18479-01 Appendix C Configuring the Switch with the CLI-Based Setup Program Entering the Initial Configuration Information You have now completed the initial configuration of the switch, and the switch displays its initial configuration. This is an example of output that appears: The following configuration command script was created: hostname switch1 enable secret 5 $1$Ulq8$DlA/OiaEbl90WcBPd9cOn1 enable password enable_password line vty 0 15 password terminal-password no snmp-server ! no ip routing ! interface Vlan1 no shutdown ip address 10.4.120.106 255.0.0.0 ! interface GigabitEthernet1/0/1 ! interface Gig

  • Cisco Catalyst 2350, A-2 Catalyst 2350 Switch Hardware Installation Guide OL18479-01 Appendix A Technical Specifications Input current C3K-PWR-265WDC: 12 A DC input voltage C3K-PWR-265WDC: –36 to –72 VDC Output ratings C3K-PWR-265WDC: 12 V@22 A Voltage range domestic C3K-PWR-265WDC: –40.5 VDC (min), –48 VDC (nominal), –56 VDC (max) Voltage range international C3K-PWR-265WDC: –55 VDC (min), –60 VDC (nominal), –72 VDC (max) Total input BTU 1 C3K-PWR-265WDC: 1305 BTUs per hour, 379 W Total output BTU 1 C3K-PWR-265WDC: 90

  • Cisco Catalyst 2350, Index IN-4 Catalyst 2350 Switch Hardware Installation Guide OL18479-01 port modes changing 1-3 LEDs 1-4 See also mode button ports 10/100/1000 connecting to 2-16 described 1-2 pinouts B-1 recommended cables 2-17 POST LEDs 4-1 running at power on 4-1 power connection warning 2-2 power specifications A-1 power-supply modules described 1-5 installation 3-1 procedures connection 2-12 to 2-13, 3-3 to 3-8 installation 2-6 to 2-11 product disposal warning 2-3 R rack-mounting 2-6 to 2-10 rear panel clearance

  • Cisco Catalyst 2350, Index IN-2 Catalyst 2350 Switch Hardware Installation Guide OL18479-01 accessing by using Express Setup C-1 accessing through console port C-1 CNA See Cisco Network Assistant code compliance warning 2-4 command-line interface See CLI connection procedures 2-12 to 2-13, 3-3 to 3-8 connectors and cables B-1 to B-7 console port connecting to C-2 connectors and cables B-4 described 1-7 crossover cable See cables D DC circuit warning 2-2 DC power connecting to 3-4 power-supply module described 1-5 power supply module installation 3-4 specifications A-1, A-2 DC power warning 3-4 dev

  • 2-17 Catalyst 2350 Switch Hardware Installation Guide OL18479-01 Chapter 2 Switch Installation Where to Go Next Where to Go Next If the default configuration is satisfactory, the switch does not need further configuration. You can use any of these management options to change the default configuration: • Start the device manager, which is in the switc

  • Cisco Catalyst 2350, ix Catalyst 2350 Switch Hardware Installation Guide OL18479-01 Preface These compatibility matrix documents are available from this Cisco.com site: http://www.cisco.com/en/US/products/hw/modules/ps5455/products_device_support_tables_list.html • Cisco Gigabit Ethernet Transceiver Modules Compatibility Matrix • Cisco 100-Megabit Ethernet SFP Modules Compatibility Matrix • Cisco Small Form-Factor Pluggable Modules Compatibility Matrix • Compatibility Matrix for 1000BASE-T Small Form-Factor Pluggable Modules Obtaining Documentation and Submitting a Service Request For information on obtaining documentation, submitting a service request, and gathering additional

  • 2-8 Catalyst 2350 Switch Hardware Installation Guide OL18479-01 Chapter 2 Switch Installation Installing the Switch Attaching the Rack-Mount Brackets You must first remove the screws from the switch chassis so that the mounting brackets can be attached. For a front-mounting position, remove two Phillips truss-head screws from the switch side panels ( Figure 2-2). For a mid-mo

  • Cisco Catalyst 2350, 3-7 Catalyst 2350 Switch Hardware Installation Guide OL18479-01 Chapter 3 Power Supply and Fan Module Installation Installing a DC-Power Supply Figure 3-6 Inserting the DC-Power Supply in Catalyst 2350 Switches Step 7 Align the two captive screws with the screw holes. Using a ratcheting torque screwdriver, torque each screw to 7 lbf-in (112 ozf-in). Step 8 Connect the input power as described in the “Wiring the DC-Input Power Source” section. Wiring the DC-Input Power Source Step 1 Using a wire-stripping tool, strip each of the four wires coming from the DC-input power source to the app

  • Cisco Catalyst 2350, 2-2 Catalyst 2350 Switch Hardware Installation Guide OL18479-01 Chapter 2 Switch Installation Preparing for Installation Warning Before working on equipment that is connected to power lines, remove jewelry (including rings, necklaces, and watches). Metal objects will heat up when connected to power and ground and can cause serious burns or weld the metal object to the terminals. Statement 43 Warning Do not stack the chassis on any other equipment. If the chassis falls, it can cause severe bodily injury and equipment damage. Statement 48 Warning An exposed wire lead from a DC-input power source can conduct harmful levels of electricity. Be sure that no exposed port

  • Cisco Catalyst 2350, 2-6 Catalyst 2350 Switch Hardware Installation Guide OL18479-01 Chapter 2 Switch Installation Installing the Switch Tools and Equipment You need to supply a number-2 Phillips screwdriver to rack-mount the switch. Installing the Switch • Rack-Mounting, page 2-6 • Table- or Shelf-Mounting, page 2-11 • After Installing the Switch, page 2-11 The illustrations shown in this section show the Catalyst 2350 switch with AC power as an example. You can install both models of the Catalyst 2350 switch following the same proced

  • Cisco Catalyst 2350, 3-5 Catalyst 2350 Switch Hardware Installation Guide OL18479-01 Chapter 3 Power Supply and Fan Module Installation Installing a DC-Power Supply Grounding the Switch To make sure that the equipment is reliably connected to earth ground, follow the grounding procedure instructions and observe these warnings: Warning This equipment must be grounded. Never defeat the ground conductor or operate the equipment in the absence of a suitably installed ground conductor. Contact the appropriate electrical inspection authority or an electrician if you are uncertain that suitable grounding is available. Statement 1024 Warnin

Related Products and Documents (Switch):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 TEFAL PRO EXPRESS ANTI-CALC Notice tefal/pro-express-anti-calc-Y36.pdf 18 Mar 2024 126 8.88 Mb
2 Havis-Shields 2000-2005 Chevrolet Impala Trak-Mount Kit C-TM-IMP Install instructions havis-shields/2000-2005-chevrolet-impala-trak-mount-kit-c-tm-imp-3OM.pdf 17 Jun 2023 2 0.24 Mb
3 Amigo MicroModem Installation manual amigo/micromodem-3YI.pdf 27 Sep 2023 37
4 Symphonic ST131E Owner's manual symphonic/st131e-A3O.pdf 06 Dec 2022 8
5 Toshiba C650D-ST4NX1 Specifications toshiba/c650d-st4nx1-PXP.pdf 17 Apr 2023 4
6 Epson 836XL - Expression - Flatbed Scanner Operation & user’s manual epson/836xl-expression-flatbed-scanner-YWM.pdf 14 Jul 2022 24 3.13 Mb

Similar Resources:

  • Tripp Lite

    B060-016-2

    (3 pages)
    Tripp Lite1111 West 35th StreetChicago, IL 60609 USATelephone: +(773) 869 1234E-mail: [email protected] Number: B060-016-2KVM Switch - 16-Port (2-User) 1U Rackmount Cat5 Matrix KVM Switch HighlightsTwo consoles independently and simultaneously control up to 16 directlyconnected computers, or over 1,000 when additional KVMs are connectedMulti-plat …
  • Extreme Networks

    WM200

    (2 pages)
    Summit WM200/2000 Controller Installation Instructions© 2007-2008 Extreme Networks, Inc. All rights reserved. Part number: 120389-00 Rev 02 Getting startedThese instructions provide installation technicians with a high-level overview for installing the Summit® WM200/2000 Controller. Unpack the controller:1 Lift the controller, in its protective foam casin …
  • H3C

    S3610 Series

    (28 pages)
    Operation Manual – File System Management H3C S3610&S5510 Series Ethernet Switches Table of Contents i Table of Contents Chapter 1 File System Management Configuration................................................................... 1-1 1.1 File System Management........................................................................................ …
  • Trimod Besta

    Bxxx5 Series

    (8 pages)
    www.trimodbesta.com 1 │ 8 LTB011EN │ 2016.04 LTB011EN Operating Instruction Trimod Besta Level Switch – type B…5 for use in potentially explosive atmospheres acc. to IECEx scheme Subject to technical modification Bachofen AG | Ackerstrasse 42 | CH-8610 Uster | Switzerland Phone +41 44 944 11 11 | F …
  • Eaton

    COOPER POWER SERIES

    (32 pages)
    Types H, 4H, and V4H maintenance instructionsType H 50 Amp reclosers - Applicable to serial numbers above 246404 or beginning with CP57.Type 4H 100 Amp reclosers - Applicable to serial numbers above 69275 or beginning with CP57.Type V4H 200 Amp reclosers - Applicable to serial numbers above 7542 or beginning with CP57.COOPER POWERSERIESReclosers MN280052ENEf …
  • Weidmuller

    IE-SW-AL08M-8TX

    (2 pages)
    1 2 3 Hardware Installation Guide Managed Fast Ethernet Switch IE-SW-AL08M-8TX (Part No. 2682280000) 1. Introduction Ethernet Switches from Weidmüller are designed for industrial applications and fitted with a robust housing. To ensure reliable, error-free operation, and to prevent damage or injury, please read the operating ins …

Comments, Questions and Opinions: