Cisco Small Business 200 Series Quick Start Manual

Text of Cisco Small Business 200 Series User Guide:

• 2 Cisco 200 Series Smart Switches Welcome Thank you for choosing the Cisco 200 Series Smart Switch, a Cisco network communications device. This device is designed to be operational right out-of-the-box as a standard bridge. In the default configuration, it will forward packets between connecting devices after powered up. Before you begin installing the switch, make sure you have all of the

• Cisco Small Business 200 Series, Cisco 200 Series Smart Switches 3 • Circuit Overloading—Adding the device to the power outlet must not overload that circuit. Rack-Mount Placement STEP 1 Remove the four screws from each side near the front of the switch. Retain the screws for re-installation. (Do not remove the four screws from each side near the back of the switch.) STEP 2 Place one of the supplied spacers on the side of the switch so the four holes of the spacers align to the screw holes. Place a rack mount bracket ne

• Cisco Small Business 200 Series, 4 Cisco 200 Series Smart Switches Connecting Network Devices To connect the smart switch to the network: STEP 1 Connect the Ethernet cable to the Ethernet port of a computer, printer, network storage, or other network device. STEP 2 Connect the other end of the Ethernet cable to one of the numbered smart switch Ethernet ports. The LED of the port lights if the device connected is active. Refer to Features of the Cisco 200 Series Smart Switches for details about the different ports and LEDs on each switch. STEP 3 Repeat Step 1 and Step 2 for each device you

• Cisco 200 Series Smart Switches 5 Power over Ethernet Considerations WARNING The switch is to be connected only to PoE networks without routing to the outside plant. If your switch is one of the Power over Ethernet (PoE) models, consider the following power requirement: CAUTION Consider the following when connecting switches capable of supplying PoE: The PoE models of the switches are P

• Cisco Small Business 200 Series, 6 Cisco 200 Series Smart Switches To prevent false detection, you should disable PoE on the ports on the PoE switches that are used to connect to PSEs. You should also first power up a PSE device before connecting it to a PoE switch. When a device is being falsely detected as a PD, you should disconnect the device from the PoE port and power recycle the device with AC power before reconnecting its PoE ports. Configuring the Cisco 200 Series Smart Switches Before You Begin Verify the managing computer requirements in the product release notes. Accessing and Managing Your Switch Using the Web- Based Interface To access the

• Cisco Small Business 200 Series, Cisco 200 Series Smart Switches 7 and reconnect the devices for them to discover their new IP addresses from the DHCP server. NOTE Details on how to change the IP address on your computer depend upon the type of architecture and operating system you are using. Use the computer Help and Support functionality to search for “IP Addressing.” STEP 3 Open a Web browser window. If you are prompted to install an Active-X plug-in when connecting to the device, follow the prompts to accept the plug-in. STEP 4 Enter the switch IP address in the address bar and press Enter. For example, http://192.168.1.254. The Switch Login Page dis

• Cisco Small Business 200 Series, 8 Cisco 200 Series Smart Switches Troubleshoot Your Connection If you cannot access your switch from the web-based interface, the switch may not be reachable from your computer. You can test network connections by using ping on a computer running Windows: STEP 1 Open a command window by using Start > Run and enter cmd. STEP 2 At the Command window prompt enter ping and the smart switch IP address. For example ping 192.168.1.254 (the default IP address of the smart switch). If you can reach the switch, you should get a reply similar to the following: Ping

• Cisco Small Business 200 Series, Cisco 200 Series Smart Switches 9 Unusually long access time: Due to the spanning tree loop detection logic, adding new connections might take 30 to 60 seconds for the affected interfaces and/or LAN to become operational. Features of the Cisco 200 Series Smart Switches This section describes the exterior of the smart switches including ports, LEDs, and connections. Not all models will have all of the features described. Ports RJ-45 Ethernet Ports—Use these ports to connect network devices, such as computers, pri

• Cisco Small Business 200 Series, 10 Cisco 200 Series Smart Switches PoE (if present)—(Amber) Located on the right of the port. Lights steady to indicate that power is being supplied to a device attached to the corresponding port. 100M LED (if present)—(Green) Located on the right of the port. Lights steady when another device is connected to the port, is powered on, and a 100 Mbps link is established between the devices. When the LED is off, the connection speed is under 100 Mbps or nothing is cabled to the port. Gigabit LED (if present)—(Green) Located on the right of the port. Lights steady when another device is connected to the port, is powered on, and a

• Cisco Small Business 200 Series, Cisco 200 Series Smart Switches 11 Where to Go From Here Support Cisco Support Community www.cisco.com/go/smallbizsupport Cisco Support and Resources www.cisco.com/go/smallbizhelp Phone Support Contacts www.cisco.com/en/US/support/ tsd_cisco_small_business _support_center_contacts.html Cisco Firmware Downloads www.cisco.com/go/smallbizfirmware Cisco Open Source Requests www.cisco.com/go/ smallbiz_opensource_request Cisco Partner Central (Partner Login Required) www.cisco.com/web/partners/sell/smb Product Documentation Cisco 200 S

• Cisco Small Business 200 Series, Americas Headquarters Cisco Systems, Inc. www.cisco.com Cisco has more than 200 offices worldwide. Addresses, phone numbers, and fax numbers are listed on the Cisco website at www.cisco.com/go/offices. Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Ciscotrademarks, go to this URL: www.cisco.com/go/trademarks. Third-party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (1110R) © 2014 Cisco Systems, Inc. All

• McGrp.Ru Сайт техники и электроники Наш сайт McGrp.Ru при этом не является просто хранилищем инструкций по эксплуатации, это живое сообщество людей. Они общаются на форуме, задают вопросы о способах и особенностях использ

More Instructions:

	Cisco Small Business 200 Series Administration manual 01-01-2024 337	DOWNLOAD
	Cisco Small Business 200 Series Administration manual 14-07-2023 202	DOWNLOAD

Related Products and Documents (Switch):

Comparable Devices:

Similar Resources:

• SMC Networks SMC8504T (2 pages) Overview0101001100100100010010110010101010011010010SMC8504TModel Number::EZ SwitchTM 10/100/10004-port Unmanaged Layer 2 + Gigabit SwitchNetwork users and applications continue to increasethe use of bandwidth intensive software programs,graphically dense materials and desire faster speeds tothe desktop. SMC EZ Switch 10/100/1000 meets thatdemand with its 4 p …

• Tripp Lite NGS8C2POE (24 pages) 1Owner’s ManualManaged Network Gigabit Ethernet Smart Switches with PoE Models: NGS8C2POE, NGS24C2POE 1111 W. 35th Street, Chicago, IL 60609 USA • www.tripplite.com/supportCopyright © 2017 Tripp Lite. All rights reserved.PROTECT YOUR INVESTMENT!Register your product for quicker service and ultimate peace of mind. You could also win an ISOBAR6ULTRA su …

• Concoa 621 Series (20 pages) 621 Series Autoswitch SystemFor use with Laser Purity GasesINSTALLATION AND OPERATION INSTRUCTIONSBefore Installing or Operating, Read and Comply with These InstructionsControls Corporation of America1501 Harpers Road Virginia Beach, VA 23454To Order Call 1-800-225-0473 or 757-422-8330 • Fax 757-422-3125www.concoa.comSeptember 2003Supersedes May 2003Cert …

• NEC EXPRESS5800 N8403-019 (170 pages) NEC Express Server Express5800 Series Express5800/T120g EXP331A, EXP332A User’s Guide Chapter 1 General Description Chapter 2 Preparations Chapter 3 Setup Chapter 4 Appendix 10.115.01-101.01April 2016© NEC Corporation 2016 …

• Extron electronics ISS 506 Series (4 pages) ISS 506 • Setup GuideNOTE: For full installation, configuration, and operation details, refer to the ISS 506 User Guide, available at www.extron.com.This guide provides quick start instructions for an experienced installer to set up and operate the Extron ISS 506 Integration Seamless Switchers, a family of seamless, scaling, video and stereo audio switch …

• Micro Innovations USB425P (1 pages) 4-Port Hi-Speed USB Hub (USB425P) Congratulations on the purchase of your new 4-Port Hi-Speed USB Hub. The 4-Port Hi-Speed USB Hub is compatible with IBM® or compatible PCs computers with an available USB port, and is supported by Windows® 98SE, Me, 2000, XP, Media Center, Vista™, Mac® OS X, v10.1x or higher (Requires a USB 2.0 PCI Card) Pac …

Comments, Questions and Opinions: