Manualios.com

Digital Equipment LN15 Operation & User’s Manual

Digital Equipment LN15 Manual Online:

3.6, 1180 votes
Digital Equipment LN15 User Manual
Digital Equipment LN15 User Guide
Digital Equipment LN15 Online Manual

Text of Digital Equipment LN15 User Guide:

  • Digital Equipment LN15, DIGITAL Laser Printer LN15 User Manual B-2 Part name (order number) Description Serial interface board RS-232C/422A (LN15X-SI) LocalTalk board LocalTalk (LN15X-AT) Ethernet board 10-Base-2 Ethernet with 10-Base-2 connector (LN15X-NA) Ethernet board 10-Base-T Ethernet with 10-Base-T connector (LN15X-NB) Paper feeder Adjustable for a different size (LN15X-TA) 500 sheets (for LN15X-TA) 1: A4, 2: Letter, 3: Legal (LN15X-TB) 450 sheets (for LN15X-TB) 1: A4, 2: Letter, 3: Legal 4: Executive, 6: A5 Paper feeder Feeder unit with a paper tray (LN15X-TC) adjustable for a different size Duplex unit Two-sided printing mechanism (LN15X-DA) Multi Function Feeder Optional fe

  • Digital Equipment LN15, DIGITAL Laser Printer LN15 User Manual 1-11 3. Lift the front of the cover to open the cover. 4. Install the cleaner in the printer. Grasp the handle of the cleaner and put the left end of the cleaner into the opening, and then the right end. 5. Lock the cleaner. Push down the top of the handle and pull it towards you to lock the cleaner. 6. Close the cover.

  • DIGITAL Laser Printer LN15 User Manual 5-4 4c.Open the rear stacker at the back of the printer. Draw out the paper guide. First push up the top edge of the paper guide and then pull out the paper guide. Caution: Do not use the lever to pull out the paper guide. The lever or the paper guide may be damaged. !

  • Digital Equipment LN15, DIGITAL Laser Printer LN15 User Manual 5-11 The most common cause of poor print quality is the dirty corona wire or precharger wire. A rare cause is the expired fuser unit. The figures below show the typical appearances. Too light White vertical line Ghost printing Black vertical line Toner stains (back) Too light White vertical line Ghost printing Clear black vertical line Toner stains (back) Smudging Due to dirty corona wire Due to dirty precharger wire Due to both Print Quality Problems Blurred black vertical line Due to expired fuser unit

  • Digital Equipment LN15, DIGITAL Laser Printer LN15 User Manual 5-14 Message Causes and solutions COVER OPEN Cause: The following occurred: •Incomplete closing of upper door •Incomplete locking of paper guide inside the rear stacker •Incomplete closing of rear unit of the optional duplex unit Solution: Perform the following. • Close the upper door. • Lock the paper guide. • Close the rear unit of the duplex unit. Note: See caution following in this table. FUSER FAILURE Cause: Malfunction in the fuser unit Solution: If the error recurs, consult your dealer for service. INVALID SIMM Cause: Incorrect SIMM card (optional emulation or font) installed Solution: Press the CONT. butto

  • Digital Equipment LN15, DIGITAL Laser Printer LN15 User Manual 3-11 Changing the Paper Tray Size The paper tray can be adjusted to one of the four paper sizes: A4, A5, LTR (Letter), and EXE (Executive). To change the size, follow these steps: 1. Remove the paper tray from the printer. Refer to the illustration for the parts you adjust when changing the size of the tray. 2. Change the setting of the paper size indicator. Lift the right end of the indicator and slide it to the desired position, that is, adjust the triangle mark to A4, A5, LTR, or EXE engraved on the tray. Label Re

  • Digital Equipment LN15, DIGITAL Laser Printer LN15 User Manual 5-18 Warning Messages This printer counts the number of the printed sheets to estimate the life of the consumables (print unit). The printer indicates the following warning message when and after the count reaches a predetermined value. READY REPLACE PARTS When the warning message is indicated, press the READY button to put the printer offline and press the MENU button to enter menu mode. The Clear Warning message appears, indicating the expired unit by an asterisk. When the print unit is expired, the message is: <CLEAR WARNING> PRINT UNIT* However, depending on the print quali

  • Digital Equipment LN15, DIGITAL Laser Printer LN15 User Manual GL-1 Glossary Application software A program that performs a particular task on a computer. Examples are word processing, spreadsheet, and database programs. Baud The speed of data transmission measured in bits per second. Baud rates apply to data transmission through the printer’s serial interface. Baud is also called baud rate. For example, 1200 baud is approximately equal to 120 characters per second. Bit A binary digit, or bit, is the smallest unit of information in

  • DIGITAL Laser Printer LN15 User Manual 4-3 you can only print about 20 more pages. Under the toner empty condition (no toner), the printer will not work. Important: Whenever you replace the toner cartridge, clean the corona wire and the precharger wire to prevent a degradation in print quality. You can continue to print after the toner low status if the print quality is still satisfact

  • DIGITAL Laser Printer LN15 User Manual GL-3 E thernet A communication hardware for a high-speed network: developed by Xerox Corporation. Factory default The settings that are programmed into a printer at the factory. The printer uses these settings unless they are replaced by user selected settings entered from the control panel or through application software. Flow co

  • Digital Equipment LN15, DIGITAL Laser Printer LN15 User Manual 1-23 If Something Goes Wrong This section briefly discusses the most common problems you might encounter. Problem Remedy No response by printer Ensure that: • The printer is turned on and online. The ONLINE indicator should be lit. • The cable from the computer to the printer is properly connected at both ends. • Your software program has sent the print data to the printer. Many programs have a printer control function that shows print No printout; DATA The printer has received data

  • Digital Equipment LN15, DIGITAL Laser Printer LN15 User Manual 4-11 Use the cleaning brush supplied with the printer. This L-shaped tool has two cleaning pads: one for the corona wire and the other for the precharger wire inside the print unit. Use the pad on the shorter branch. Remove the print unit and store it in a dark, level, steady place. Be careful not to damage the green drum surface. Using the tool as shown in this figure, clean the corona wire. Fit the positioning cut onto the wire housing frame and gently move th

  • Digital Equipment LN15, DIGITAL Laser Printer LN15 User Manual 4-8 unnecessary high coverage printing to maintain the print unit performance. For the print unit life, this printer indicates the near end of life only. The message begins displaying ' REPLACE PARTS', when the print unit can still print 3,000 to 5,000 more pages. Prepare a new print unit if you notice this indication. Even if the print unit reaches its near-end-of-life, use the print unit until its toner runs out (the message display indicates TONER EMPTY ) for economy. After replacing the print unit, be sure to reset the print unit counter by using the

  • DIGITAL Laser Printer LN15 User Manual 1-12 Loading the paper This printer has a single paper tray that is preset for letter size (8.5 x 11.0 inches) paper for U.S. customers and to A4 size (210 x 297 mm) paper for European customers. You can adjust the paper tray to a different size paper. You can purchase an optional paper tray. You should load about 50 sheets of

  • Digital Equipment LN15, DIGITAL Laser Printer LN15 User Manual 3-6 Selecting the Serial Interface The printer’s standard interface is parallel. When the serial interface board is installed, the printer automatically detects that the computer is using the serial interface. Verifying Serial Parameter Settings Next, you must make sure the serial parameter settings are the same between the computer and the printer. Consult your computer and software documentation to determine the settings your computer uses. Then compare these to the printer’s settings in the following table. Item Parameter setting (default) Baud rate 9600 Data bits 8 Stop bits 1 Parity None Flow contr

  • Digital Equipment LN15, DIGITAL Laser Printer LN15 User Manual 2-13 Use + and - to move up and down the options list. When an item is displayed, ENTER selects that option (adds an asterisk after the option indicating that the option is stored in RAM). MENU MENU MENU SETUP MENU QUALITY MENU PAPER LETTER* MENU PAPER LEGAL + – + SMOOTHING ON* SETUP MENU PAGE FORMAT MENU COPIES 001* ENTER COPIES 002 + – + – MENU READY ENTER – + – MENU SMOOTHING OFF

  • Digital Equipment LN15, DIGITAL Laser Printer LN15 User Manual 3-15 To install and use the duplex unit, refer to the DIGITAL LN15X-DA Duplexing Unit User Manual. Caution: To avoid possible personal injury or harm to your equipment, cooperate with another person in assembling or disassembling the printer, duplex unit, multi-function feeder, and paper feeder (if installed). Do not lift or move the printer as equipped with other units. Notice: Be sure to keep the rear opening of the duplex unit away from a wall or another equipment s

  • Digital Equipment LN15, DIGITAL Laser Printer LN15 User Manual 1-7 This section describes how to assemble the printer and connect the power cord after choosing a suitable location for the printer and checking that you received all the parts. Preparing the Print Unit and Installing the Toner Cartridge This printer is shipped with the print unit mounted and protective materials attached. Be sure to remove the two protective materials from the print unit. This operation is possible with the print unit mounted. First prepare and install

  • Digital Equipment LN15, DIGITAL Laser Printer LN15 User Manual 4-15 POWER ONLINE DATA ERROR MFF PAPER SIZE PRINT FONT SELF TEST RESET CONT. ENTER – + MENUREADY FORM FEED RESET MENU TRAY SELECT MFF PAPER SIZE PRINT FONT SELF TEST RESET CONT. ENTER – + MENUREADY FORM FEED RESET MENU TRAY SELECT POWER ONLINE DATA ERROR POWER ONLINE DATA ERROR Resetting the Print Unit Counter Perform this operation whenever you have replaced the print unit, or the printer continues displaying the warning message REPLACE PARTS . To reset the print unit counter, follow these steps: 1. Make sur

  • Digital Equipment LN15, DIGITAL Laser Printer LN15 User Manual 1-18 • Serial (RS-232C/422A) Use a serial interface if the printer is not near the computer. Many computers have both parallel and serial interface ports. Serial communication can operate up to 15 meters (50 feet). Parallel communication is normally limited to 3 meters (10 feet). • LocalTalk Use the LocalTalk interface if the printer is connected to a Macintosh computer. • Ethernet Use the Ethernet interface if the printer is used in a network environment. Notice: The DIGITAL Laser Printer LN15N-A and LN15N-B are equipped w

Related Products and Documents (Printer):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 Casio 5344 Operation manual casio/5344-312.pdf 06 Feb 2024 1 0.26 Mb
2 Datalogic DX6400 Reference manual datalogic/dx6400-UT5.pdf 23 Oct 2022 94 7.39 Mb
3 Audiovox D1805 Instruction manual audiovox/d1805-5BA.pdf 16 Jun 2023 33 0.42 Mb
4 Baby Lock Quest PLUS BLQ2-PL Instruction and reference manual addendum baby-lock/quest-plus-blq2-pl-516.pdf 06 Mar 2024 2 0.23 Mb
5 NETGEAR WNHD3004 - High Performance Wireless-N HD Home Theatre Adapter Datasheet netgear/wnhd3004-high-performance-wireless-n-hd-home-theatre-adapter-2G9.pdf 19 Jul 2022 3
6 Sharper Image EC-W130 Instruction manual and warranty information sharper-image/ec-w130-R46.pdf 06 Feb 2024 4 0.3 Mb

Similar Resources:

  • Canon

    POWERSHOT A75

    (2 pages)
    4Erasing an Image➜ Camera User Guide3Playback➜ Camera User GuideCDI-E139-010 © 2004 CANON INC. PRINTED IN MALAYSIA1Preparing the Camera➜ Camera User Guide➜ Camera User GuideQuick Reference➜ Camera User GuideZoomShooting Modes: AutoThe camera automatically selects settings.: PortraitThe background is blurred and the subject is in clearfocus.: …
  • Dell

    B5465dnf Mono Laser Printer MFP

    (2 pages)
    Safety InformationKeep this sheet with the printer documentation.CAUTIONTIPPING HAZARD: Installing more than one input option on your printer or multifunction printer (MFP) may require a caster base to prevent instability, which can cause injury. For more information on supported input option configurations, see the Option Configuration Guide at www.stabl …
  • Intermec

    PW50

    (2 pages)
    Worldwide Headquarters6001 36th Avenue WestEverett, Washington 98203U.S.A.tel 425.348.2600fax 425.355.9551www.intermec.com© 2008 Intermec TechnologiesCorporation. All rights reserved.PW50 Workboard Printer Quick Start Guide*930-209-002*P/N 930-209-002Guide de démarrage de l’imprimante WorkboardWorkboard Drucker-KurzanleitungManual de Consulta Rápida …
  • Waterpik Technologies

    AQUALINK RS485

    (1 pages)
    Phone Cablefrom Wall Jack.AquaLink RSTeleLink BoardTo RS4854-ConductorCable(Cable betweenController andPower Center)2Program# of rings(default: 4)Programaccess code(default: 62)®redblackyellowgreen1CautionDo not mount the TeleLink PCB in theAquaLink Power Center. Keep in originalTeleLink enclosure.!The TeleLink enclosure will need to be installed as close …
  • Epson

    ActionLaser II

    (2 pages)
    EPSON AMERICA, INC.EPSONProduct Support BulletinSubject: How To Connect Epson PostScript Printers Into An AppleTalk NetworkDate: 10/9/92Page(s): 1 of 1PSB No: P-0092Originator: SDSThis bulletin provides information on how to interface Epson laser printers with anEpson PostScript’ Card to an Apple Macintosh2 using Apple LocalTalk3 and theBridgeport4 by Exte …
  • Lexmark

    MS810n

    (1 pages)
    Mono Quality GuideQuality menuUse ToPrint Resolution300 dpi600 dpi1200 dpi1200 Image Q2400 Image QSpecify the printed output resolution in dots per inch.Note: 600 dpi is the factory default setting.Pixel BoostOffFontsHorizontallyVerticallyBoth directionsEnable more pixels to print in clusters for clarity, in order to enhance images horizontally orvertically, …

Comments, Questions and Opinions: